Philips 40PFL7664H/12 Service Manual page 33

• Select a COLOUR TEMPERATURE (e.g. COOL,
NORMAL, or WARM).
• Set the RED, GREEN and BLUE default values according
to the values in Table
• When finished press OK on the RC, then press STORE (in
the SAM root menu) to store the aligned values to the NVM.
• Restore the initial picture settings after the alignments.
Table 6-2 White tone default settings 40" Frame sets
White Tone
Colour Temp R
Normal 127
Cool 123
Warm 127
6.4 Option Settings
6.4.1 Introduction
The microprocessor communicates with a large number of I
ICs in the set. To ensure good communication and to make
digital diagnosis possible, the microprocessor has to know
which ICs to address. The presence / absence of these
PNX5120 ICs (back-end advanced video picture improvement
IC which offers motion estimation and compensation features
(commercially called HDNM) plus integrated Ambilight control)
is made known by the option codes.
Notes:
• After changing the option(s), save them by pressing the OK
button on the RC before the cursor is moved to the left,
select STORE in the SAM root menu and press OK on the
RC.
• The new option setting is only active after the TV is
switched "off" / "stand-by" and "on" again with the mains
switch (the NVM is then read again).
6.4.2 Dealer Options
For dealer options, in SAM select "Dealer options".
See Table 6-5.
6.4.3 (Service) Options
Select the sub menu's to set the initialisation codes (options) of
the model number via text menus. See
6.4.4 Opt. No. (Option numbers)
Select this sub menu to set all options at once (expressed in
two long strings of numbers).
An option number (or "option byte") represents a number of
different options. When you change these numbers directly,
you can set all options very quickly. All options are controlled
via eight option numbers.
When the NVM is replaced, all options will require resetting. To
be certain that the factory settings are reproduced exactly, you
must set both option number lines. You can find the correct
option numbers on a sticker inside the TV set and in
Example: The options sticker gives the following option
numbers:
• 08192 00133 01387 45160
• 12232 04256 00164 00000
The first line (group 1) indicates hardware options 1 to 4, the
second line (group 2) indicate software options 5 to 8.
Every 5-digit number represents 16 bits (so the maximum value
will be 65536 if all options are set).
When all the correct options are set, the sum of the decimal
values of each Option Byte (OB) will give the option number.
See Table 6-3 for the options.
6-1.
Black level offset
G B R
114 114 8
122 126 8
110 67 8
Table 6-5.
Table
Alignments
Diversity
Not all sets with the same Commercial Type Number (CTN)
necessarily have the same option code!
Use of Alternative BOM An alternative BOM number usually
indicates the use of an alternative display or power supply. This
results in another display code thus in another Option code. For
the power supply there is no difference.
Refer to Chapter 3. Precautions, Notes, and Abbreviation List.
6.4.5 Option Code Overview
G Table 6-3 Option and display code overview
8
8
CTN
(Alt. BOM#)
8
40PFL8664H/12 12307 00642 02031 45288 30689 28850 08867 00000 225
40PFL7664H/12 12291 00642 02031 45288 30689 28850 08867 00000 225
Important: after having edited the option numbers as
described above, you must press OK on the remote control
before the cursor is moved to the left!
2
C
BBE & WMA Functionality
Some sets have the possibility to switch "on" the "BBE" and/or
"WMA" functionality for an enhanced audio experience. This
has to be executed via ComPair via "option 9".
Table 6-4 "Option 9" overview
CTN
(Alt. BOM#)
40PFL8664H/12
40PFL7664H/12
6.5 Reset of Repaired SSB
A very important issue towards a repaired SSB from a service
repair shop implies the reset of the NVM on the SSB.
A repaired SSB in service should get the service Set type
"00PF0000000000" and Production code "00000000000000".
Also the virgin bit is to be set. To set all this, you can use the
ComPair tool.
In case of a display replacement, reset the "Operation hours" to
"0", or to the operation hours of the replacement display.
6.5.1 SSB identification
Whenever ordering a new SSB, it should ne noted that the
correct ordering number (12nc) of a SSB is located on a sticker
on the SSB. The format is <12nc SSB><serial number>. The
ordering number of a "Service" SSB is the same as the ordering
number of an initial "factory" SSB.
6-3.
Q548.1E LB 6.
Options Group 1 Options Group 2
Option 9
00057
00057
EN 33
Disp.
code
2009-Dec-18