Advertisement
Quick Start Guide
Quick Start Guide
Be sure to install the software programs before connecting the scanner
to the computer!
Please read this guide before operating this scanner. After you finish reading this guide, store it in
a safe place for future reference.
Setup and Scanning
Try the Additional Features
3
4
5
6
7
10
11
1
Advertisement
Table of Contents
Related Manuals for Canon CanoScan 4200F
Summary of Contents for Canon CanoScan 4200F
-
Page 1: Table Of Contents
Be sure to install the software programs before connecting the scanner to the computer! Please read this guide before operating this scanner. After you finish reading this guide, store it in a safe place for future reference. Setup and Scanning... -
Page 2: Arcsoft Photostudio
Adobe Acrobat Reader should be installed on your computer. The socket-outlet shall be installed near the equipment and shall be easily accessible. Use of a shielded cable with the ferrite core(s) provided with the scanner is necessary to comply with the technical requirements of the EMC Directive. -
Page 3: Check The Package Contents
It also works with the scanner buttons. ArcSoft PhotoStudio (35 MB) - Image Editing Program It allows you to load images from the scanner, edit and retouch them, and apply special effects and enhancements. ScanSoft OmniPage SE* (90 MB) - OCR (Optical Character Recognition) Program It converts characters scanned from a book, magazine or newspaper into text data for editing or digital transmission. -
Page 4: Install The Software
Install the Software Install the Software • If you are running Windows XP or Windows 2000 Professional with multiple user accounts, you should log on with an administrator user name when installing or uninstalling software programs. Turn the computer on. If the "Found New Hardware Wizard"... -
Page 5: Unlock The Scanning Unit
• Do not tilt the scanner more than 90 degrees from horizontal when releasing the lock. • When locking the scanner, do not lift up the back and tilt the front (scanner button location) downward. You may be unable to set the lock. -
Page 6: Connect The Scanner
• When the scanner is connected to the USB 1.1 port on Windows XP, do not worry if the "HI-SPEED USB Device Plugged into non-HI-SPEED USB Hub" message appears. You can operate the scanner in this condition without problems. -
Page 7: Try Scanning
Try Scanning The following steps explain how to scan with ArcSoft PhotoStudio. Place a photo or a picture on the glass by aligning its top edge with the alignment mark, and close the document cover. Select [Start], [Programs] or [All Programs], [ArcSoft PhotoStudio 5.5] and [PhotoStudio 5.5]. - Page 8 Try Scanning Click the [File] menu and choose [Select Source]. Select your scanner model name and click the [Select] button . • You do not need to set it from the second time onward with the same scanner. • You will need to do this step if you select a different scanner or a digital camera.
- Page 9 Click the close box to close it. • If the scanner does not perform as described above, read the "Troubleshooting" section of the Scanning Guide (HTML format manual). • For details about the bundled software programs, read the Scanning Guide or the user guides (PDF format manuals) for each software program on the CanoScan Setup Utility CD-ROM.
-
Page 10: Using The Scanner Buttons
Using the Scanner Buttons You can use the four convenient buttons on the front of the scanner to scan and perform related tasks easily with a single touch of the button. Place a photo or a picture on the scanner before pressing a button. -
Page 11: Scanning Film
• Always put the protective sheet back when you are not scanning film to protect the light source in the document cover. • You can purchase the Accessory Kit for CanoScan 4200F (CSAK-4200F) if the protective sheet or Film Guide are lost or damaged. - Page 12 Scanning Film Insert a fingernail into the slot in the Film Guide and open the Film Holder. Insert the film into the Film Guide. • Hold the film by the edges with your fingertips to avoid getting fingerprints or dirt on the film surface.
- Page 13 Return the Film Guide to the document cover. Hold the document cover and document cover, and then securely into place with a click. Close the document cover. When you close the document cover, check the document glass to ensure that there are no photographs or documents left upon it.
- Page 14 Scanning Film Scanning Film The following steps explain how to scan the film with ArcSoft PhotoStudio. Start ArcSoft PhotoStudio. Refer to step 2 on page 7. Start ScanGear CS. Refer to step 4 on page 8. Select the [Select Source]. You can select from the following options for films.
- Page 15 Click the close box in the PhotoStudio window to close it. • If the scanner does not perform as described above, read the "Troubleshooting" section of the Scanning Guide (HTML format manual). • For details about the bundled software programs, read the Scanning Guide or the user guides (PDF format manuals) for each software program on the CanoScan Setup Utility CD-ROM.
-
Page 16: Specifications
Calibration processing time is not included. Slides must be less than 2 mm thick. AC adapter type varies according to the region in which the scanner is purchased. • Specifications are subject to change without notice. Upgrading to USB 2.0 To upgrade a computer to the USB 2.0 standard, please use one the following USB expansion cards/hubs... -
Page 17: System Information
Attached Peripherals: Connected Network System: As an ENERGY STAR Partner, Canon Inc. has determined that this model meets the ENERGY STAR Program for energy efficiency. The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the use of computers and other office equipment.