Advertisement
2.
INTRODUCTION
i
High powered, lightweight industrial unit with blower facility. Constructed from stainless steel, the drum unit is mounted on two castor and two
fixed wheels. Tool storage points on head and base. Supplied with 4.5m cable with 3-pin plug, deluxe tool kit, including stainless steel telescopic
rigid extension tube, cartridge filter and wet-use foam filter.
3. SPECIFICATION
Model no ........................................................... PC300SD.V3
Airflow ....................................................................... 120m³/h
Drum size ......................................................................... 30L
Filter type ................................................................ Cartridge
Max. vacuum pressure ............................................. 160mbar
Motor power ................................................................1400W
Optional accessories
PC300PB5 .............................. optional dust bags (pack of 5)
Replacement parts
PC200CFL .................................................... Cartridge Filter
PC200FF10 ................................... Foam Filters (Pack of 10)
Supply ..........................................................................230V~
Vacuum accessories diameter ..................................... 35mm
4. CONTENTS
Item
Description
1
Handle
2
ON/OFF switch
3
Top section
4
Filter basket
5
Safety float valve
6
Clasp
7
Container
8
Vacuum hose connection
9
Drain Plug
10
Flexible vacuum hose
5. ASSEMBLY
5.1.
Ensure the mains plug is disconnected. (fig.2.1)
5.2.
Undo clasps. (fig.2.2)
5.3.
Lift off the top section assembly. (fig.2.3)
5.4.
Remove contents from inside the container. (fig.2.4)
5.5.
Turn the container upside down and insert the castors ensuring they
are pushed all the way in. (fig.2.5a)
5.6.
Insert the rear wheel shaft (N) into the rear support block. Insert washer
(M) on the shaft, then insert rear wheel (K) on the shaft. Insert the lock
pin (R) into the hole on the end of the shaft to lock the wheel.
5.7.
Snap the hub cap (O) on to the wheel. Repeat the same steps at the
other end of the shaft. (fig.2.5b)
5.8.
For wet vacuum cleaning fit the supplied foam filter. (fig.2.7)
5.9.
For dry vacuum cleaning use the cartridge filter supplied. (fig.2.6)
NOTE: DO NOT operate the cleaner without a cartridge filter fitted
as this will damage the machine and invalidate your warranty.
5.10.
Replace the top section onto the container. (fig.2.8)
5.11.
Align up the top section with the clasps and snap into place, by applying
pressure at the mid point of the clasps. (fig.2.9)
5.12.
Insert the large end of the hose into the front inlet of the container and
lock in place by turning clockwise a quarter turn. (fig.2.10)
5.13.
Choose the desired nozzle and push it onto the telescopic suction tube.
6. DRY VACUUM CLEANING
WARNING! Ensure you read, understand and apply Section 1 '
‰
Safety Instructions'.
Reminder: DO NOT vacuum hazardous substances. Use of an
incorrect cartridge filter will invalidate your warranty.
6.1.
Ensure the machine is unplugged from the power supply. (fig.3.1)
6.2.
Remove the top section and fit the cartridge filter down over the
6.3.
filter basket and push fully home. (fig.3.2)
6.4.
Reposition the head onto the drum body, and clip in place. (fig.3.3)
6.5.
Insert the larger end of the flexible hose into the front inlet on the
attachment onto the free end of the hose. (fig.3.4)
6.6.
Plug in the power supply. (fig.3.5)
6.7.
Switch to the 'On' (position 'I'). (fig.3.6)
6.8.
When you have completed vacuuming, press the switch to 'Off'.
© Jack Sealey Limited
Item
Description
11
Telescopic suction tube
12
Blow connection
13
Combination nozzle
14
air regulator handle
15
Foam filter
16
Crevice nozzle
17
Cartridge filter (fitted as
standard)
18
Noise Diffuse muffler
Original Language Version
container and lock in place. Push the required
PC300SD.V3 Issue:4 (F) 19/08/20
fig.1
fig.2
fig.3
Advertisement
