Advertisement
Available languages
Available languages
Quick Links
AUTOMATIC CONDENSATE UNIT
RULES FOR SAFE OPERATION
1.
Carefully read the Owners Manual and rules for safe operation.
2.
All wiring must conform to local codes. Use the National Electric Code if local code is nonexistent.
3.
CAUTION! To reduce risk of electric shock disconnect form power supply before servicing, pull the plug on models which have
plug-in connections.
4.
Do not handle the pump with wet hands or when standing in water as fatal shock could occur. Disconnect main power before
handling unit for ANY REASON!
5.
Protect the power cable from coming in contact with sharp objects.
6.
Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces or chemicals.
7.
Make certain that line voltage conforms to the voltage specified on motor and nameplate.
8.
WARNING! To reduce risk of electrical shock, connect only to a properly grounded grounding type receptacle.
Select a location for the pump. It should be as
near as possible to the air conditioning coil.
The pump must be level. The inlet hole must
be below the coil drain.
Carefully unpack the pump. Remove the
switch/motor cover. Check each float arm for
"free" action.
Owners Manual
Keep For Future Reference
INSTALLATION OPERATION
&$87,21 Read rules for Safe Operation and Installation.
&$87,21
&$87,21
&$87,21
Model: CB22
20' LIFT
Models:
CB221UL - 115V
CB222UL - 230V
INTRODUCTION
INSTALLATION
BECKETT CORPORATION
Irving, Texas
www. beckettpumps.com
Phone: 972-871-8000
Toll Free: 1-888-BECKETT
Fax: 972-871-8888
© 2010 BECKETT CORPORATION All Rights Reserved
FAN
OUTLET
INLET
STAND
MOTOR
SAFETY SWITCH
PRIMARY
SWITCH
PRIMARY
FLOAT
SAFETY
FLOAT
Y8627 Rev. B
Advertisement
Related Manuals for Beckett CB22
Summary of Contents for Beckett CB22
- Page 1 Carefully unpack the pump. Remove the switch/motor cover. Check each float arm for “free” action. STAND PRIMARY FLOAT BECKETT CORPORATION SAFETY Irving, Texas FLOAT www. beckettpumps.com Phone: 972-871-8000 Toll Free: 1-888-BECKETT Y8627 Rev. B Fax: 972-871-8888 © 2010 BECKETT CORPORATION All Rights Reserved...
-
Page 2: Maintenance And Troubleshooting
Replace inlet line into pump inlet. TESTING – Temporarily remove inlet tubing WIRING connecting evaporator drain to pump. Pour water FOR CB22 slowly into pump inlet. Control float should rise until snap switch turns on pump. MAINTENANCE AND TROUBLE SHOOTING Remove dirt that may collect in bottom sump. -
Page 3: Installation
POMPE À CONDENSATS AUTOMATIQUE À conserver pour référence ultérieure INSTALLATION FONCTIONNEMENT AVERTISSEMENT Lire attentivement les directives pour s’assurer d’un fonctionnement et d’une installation sécuritaires. N° de Modèle CB22 ÉLÉVATION DE 6,1 M N° de Modèle CB22 CB221UL – 115V CB222UL – 230V INTRODUCTION DIRECTIVES DE FONCTIONNEMENT SÉCURITAIRE... -
Page 4: Entretien Et Dépannage
Le flotteur de contrôle MODÈLE doit monter jusqu’à ce que l’interrupteur à rupture brusque mette la CB22 pompe en fonction. ENTRETIEN ET DÉPANNAGE Éliminer la saleté pouvant s’accumuler au fond du réservoir d’épuisement. -
Page 5: Instalación
/ motor. Verifique cada brazo de la flota para la acción Flotador "libre". Primario El Soporte BECKETT CORPORATION Irving, Texas www. beckettpumps.com Phone: 972-871-8000 Flotador de Y8627 Rev. B Toll Free: 1-888-BECKETT Seguridad Fax: 972-871-8888 © 2010 BECKETT CORPORATION Derechos Reservados... - Page 6 PRUEBA – Temporalmente remueva el tubo de entrada. Ponga ALAMBRADO agua lentamente a la entradada de la bomba. El flotador debe PARA CB22 de levantarse hasta que prenda el interruptor, prendiendo la bomba. MANTENIMIENTO Y DETECCIÓN DE FALLAS Remueva la suciedad que pudo haberse juntado en el fondo del sumidero.