Advertisement
Quick Links
Advertisement
Related Manuals for Gigaset ONE X5100
Summary of Contents for Gigaset ONE X5100
- Page 1 ONE X5100 Quick start guide For users of Smart Home...
- Page 2 Gigaset ONE X5100 controller supports only one association group - the lifeline association group - and only one node can be assigned to it. The group is used by Gigaset ONE X5100 to send Device Reset Locally Notification. All Z-Wave Plus certified devices from any manufacturers are compatible with Gigaset ONE X5100 Z-Wave Plus controller.
- Page 3 How to install Gigaset ONE X5100 Connect power adapter with Gigaset ONE X5100 and plug into the socket. To start up Gigaset ONE X5100, please follow these steps and instructions. Please also observe the instructions included. For more information, go to www.gigaset.com The LED starts flashing green.
- Page 4 Gigaset ONE X5100 Open your web browser, go to the web overview page of your router and log in there. Enter the IP address of Gigaset ONE X5100 into your browser. Select the overview of connected devices (e.g. Home Choose Z-Wave Portal in the top left corner of the page.
- Page 5 Add a Z-Wave device Remove a Z-Wave device via ADD DEVICE Enter the Z-Wave Portal Enter the Z-Wave Portal From the menu choose DEVICES and then + ADD DEVICE Choose MORE, then MAINTANACE and then REMOVE DEVICE Now start the inclusion procedure of your Z-Wave device according to its manual Now start the removing procedure of your Z-Wave device according to its manual...
- Page 6 Status: Use Pending if you want to add your device. Use Ignored if you never want to add your device Now tab on ADD DEVICE, so Gigaset ONE X5100 starts to scan for your device after it has been powered up...
- Page 7 Managing added SmartStart devices Enter the Z-Wave Portal From the menu choose MORE then SMARTSTART The list of added devices will be displayed The status of each device is shown on right side, it can be changed to Ignore by selecting this status from the drop down list Click on EDIT (it will change to DONE) and now by clicking on the name of the device you are able to edit all entered...
- Page 8 Z-Wave Factory Reset If this controller is the main controller for your network, resetting it will result in the nodes in your network being orphaned and it will be necessary after the reset to remove and add again all of the nodes in the network. If this controller is being used as a secondary controller in the network, use this procedure to reset this controller only in the event that the network primary controller is missing or...
- Page 9 Now enter Z-Wave Portal From the menu choose MORE, MAINTANACE and then SET LEARN MODE to add Gigaset ONE X5100 as an inclusion / secondary controller After couple of minutes Gigaset ONE X5100 is in the same network as the main controller...
- Page 10 DSK and PIN If you need the DSK or the PIN of the Gigaset ONE X5100 you can find them: PIN: On the bottom right of the Gigaset ONE X5100 DSK: top right on the label of the packaging as QR code...
- Page 11 Setting Learn Mode, reading your DSK If your Gigaset ONE X5100 has no sensors added (e.g. it has The LEARN MODE is active, the DSK will be displayed in the been just reset to factory settings) you can set the LEARN popup after couple of seconds.
- Page 12 / secondary controllers for Basic Commands If Gigaset ONE X5100 is the SIS controller: If Gigaset ONE X5100 controller will receive Basic SET and GET commands they will be ignored. Enter the Z-Wave Portal However Basic SET command can be sent by the controller to From the menu choose DEVICES and + ADD DEVICE or included nodes to set up any value.
- Page 13 Supported Z-Wave Command Classes This is the list of supported non-secure Command Classes: This is the list of supported secure Command Classes: 0x5E - COMMAND_CLASS_ZWAVEPLUS_INFO 0x34-COMMAND_CLASS_NETWORK_MANAGEMENT_ INCLUSION 0x55 - COMMAND_CLASS_TRANSPORT_SERVICE 0x52 - COMMAND_CLASS_NETWORK_MANAGEMENT_ 0x56 - COMMAND_CLASS_CRC_16_ENCAP PROXY 0x22 - COMMAND_CLASS_APPLICATION_STATUS 0x4D - COMMAND_CLASS_NETWORK_MANAGEMENT_ 0x6C - COMMAND_CLASS_SUPERVISION BASIC...
-
Page 17: Contents Of The Package
Do you have any questions or want detailed information on our security solutions? We look forward to welcoming you on www.gigaset.com. Helpful videos are also on our YouTube and Facebook sites. Support is available directly from the app and on www.gigaset.com/support.