Table of Contents
Advertisement
The programme position setup menu
The receiver is already preprogrammed for the cur-
rent channels of many satellites. In most cases, a
correction is not required.
However, new programmes are continuously added
or transmission frequencies are changed. The cur-
rent state of the transmission frequencies can be
called up by means of the Teletext pages of various
stations (e.g. SAT1: Teletext page 675), or the infor-
mation required can be found in TV programme
guides. Changed programmes then can be re-pro-
grammed in a simple way.
In the "Programme position setup" menu, you have
access to the picture and sound settings of the indi-
vidual programme positions.
1
Use the numeric keys or the ] | keys to select
the programme position for which you wish to
check or change the settings.
!
It is not possible to select the programme position
by its number in the menus.
❒
Overview
1
Press the
On the picture screen appear the status menu and
then the programme position setup menu.
&
A
$
~
(
{
/
=
/ OK
Meaning of symbols:
&
A 300
11.494 GHZ
$
V~B
7.02 MHZ 7.20 MHZ Left and right sound carrier
~ PANDA
BW 1
(
{
1
/
X–X
=
+
/ OK
12
2
key and then the
key.
.
300
11.494 GHZ
V–
7.02 MHZ
7.20 MHZ
PANDA
BW 1
1
X–X
+
TUNER A or B
300 = Programme position
number
Satellite channel transmis-
sion frequency.
Selection of polarization,
22 kHz signal on/off,
Satellite selection A/B/C/D.
Deemphasis /noise
suppression.
Bandwidth (levels 1 to 4)
Favourite programme
Contrast setting
Decoder setting
Normal/inverse picture
: exit menu,
OK: save and exit menu.
❒
Programme position number (
The programme position number and tuner input is
displayed for checking. They cannot be changed in
the menu.
❒
Satellite channel transmission
frequency ( )
You can directly enter the satellite channel trans-
mission frequency with the numeric keys or change
the value in 1 MHz steps with the
❒
Polarization, switching signal and
LNC input ($)
You can select whether you wish to receive a hori-
zontally (H) or vertically (V) polarized signal (with V,
at 14 V, and with H, at 18 V direct voltage is applied
at the LNC).
When receiving with several satellite aerials or
LNC's, or for LNC range switch-over, you can
select the signal source by switching on and off the
22 kHz signal and by using the A/B/C/D satellite sel-
ect function (see chapter "Multi-Satellite Reception").
❒
Sound frequencies (
1
Audio frequencies can be entered directly on the
remote control handset using keys
7.02 MHz is entered by pressing
can increment the current value in steps of 1 MHz
to a new value by pressing the
One can toggle to right channel frequency by pres-
2
sing the | key, operation is identical to above.
❒
Deemphasis/noise suppression ( ~ )
You have the choice between PANDA, 50 µs
1
(50 US), and J17. Select the option giving the best
sound quality.
❒
Bandwidth (BW)
1
You can select from four bandwidth settings
(BW 1 ... BW 4) for the de-emphasis settings 50µs
(50US) and J17. It is best to decide according to
your own impression of the sound.
For the PANDA de-emphasis setting the bandwidth
is fixed to setting BW 1.
&
A/B)
keys.
x c
)
0
9
to
e.g.
7
0
2
,
&
or one
or
key.
x
c
Advertisement
Table of Contents
