Related Manuals for Lawn Genie L60204
Summary of Contents for Lawn Genie L60204
- Page 1 Lawn Dual-Program Electronic Controller Installation and Operation Guide attempting to install or operate controller.
- Page 2 It lets you supply it controls are called a Zone. “Selecting the right controller and program different parts of your lawn The L60204 lets you divide Program” on page 10. Installing the controller..........6 it for the watering and garden with precisely your yard into as many as four Connecting the valves..
- Page 3 (1) Time key For setting time of day. (2) Hours key For setting current hour, start-time hour, and advancing run time in 1-minute increments. For setting current minute, start-time minutes, and advancing run time in l-minute increments. Manual key For temporarily interrupting a watering cycle in progress, or manually start ing a watering cycle at other than the programmed time.
- Page 4 Wire the valves Select the location A. Run valve wiring underground wherever possible. Wires to individual controller terminals A. Choose an indoor location near a standard 120-volt Common wire to single controller For line runs less than 800 feet long, use 18-gauge, dual electrical outlet.
- Page 5 C. Press w and hold key down until display shows current minute. To advance time quickly, hold A battery back-up system is built into your Lawn Genie down E or ME until desired time approaches. controller to maintain your programmed watering To advance time slowly, digit by digit, press E or schedule in memory in case of temporary power failure.
- Page 6 Divide up your yard Assign start times to each Program Now You’re ready to select the times of day that each To accommodate the special watering needs of different Program will begin watering the Zones assigned to it. parts of your yard, You can assign Zones to two separate Your controller lets you set as many as six start times watering Programs (A and B).
- Page 7 To set the start times for Program B Set Program A Zones NOTE: Skip this step if all Zones will be set to run A. Press s once to display This indicates on the same day. using the same start times. Zone1 is set to run for 5 minutes on the days assigned Simply place all Zones in Program A.
- Page 8 You can program a group of Zones to water either on E. Follow the same steps if you wish Program B to water specific days of the week (Sunday through Saturday) by day interval, using E or at specific intervals between watering days, (every day, every 2nd day, every 3rd day, etc.).
- Page 9 Here’s an example of how you might use your Lawn Genie To connect your controller to a well pump or controller to program a watering schedule for a typical master valve: lawn and garden. Please refer to instructions on the preceding pages for details on specific keystroke If your water doesn’t come from the pipes of a standard...
- Page 10 Manual watering- to water a selected Zone Interrupting the watering cycle- Pause Function To freeze a manual or semi-automatic watering cycle at To water a single Zone at a time, press MI\NUI\L once, any point in the Zone’s run time, press s The display then repeatedly press E or z to advance to the will flash lSSE To resume the watering cycle, press s Zone number you wish to water.
- Page 11 Malfunctions aren’t common, but when they If possible, schedule watering cycles in the early morning, o c c u r , they’re often due to one of these when water pressure is at its highest. This allows ample frequently overlooked causes. time for water to soak in while evaporation and wind drift are low.
-
Page 12: Limited Warranty
This warranty does not apply to damages or malfunctions resulting from accidents, misuse or neglect. Lawn Genie will not pay labor or other costs of removal or reinstallation of any so-called defective products. NO IMPLIED WARRANTIES (INCLUDING BUT NOT... - Page 13 Zone Watering Days Run lime location Start limes (maximum total of six) Program A or Program B LawnGenie 9455 Railroad Drive El Paso, TX 79924 (915) 757-2586 800-231-5117 Hardie Irrigation 200702 REV. A 1/93...