Advertisement

SERVICE MANUAL
Ver. 1.2 2010.06
• HCD-FX300i (US, CND, UK, SP, TW, KR, TH,
AUS) is the amplifi er, CD player, tuner and
iPod section in CMT-FX300i (US, CND, UK,
SP, TW, KR, TH, AUS).
• HCD-FX300i (AEP, E2, E51, MX) is the ampli-
fi er, CD player, tuner, USB and iPod section in
CMT-FX300i (AEP, E2, E51, MX).
iPod is a trademark of Apple Inc., registered in the U.S.
W
and other countries.
MPEG Layer-3 audio coding technology and patents
W
All other trademarks and registered trademarks are of
W
TM
their respective holders. In this manual,
and
• Abbreviation
AUS
: Australian model
CND : Canadian model
E2
: 120V AC area in E model
Ampli er section
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(
e United States model only)
With 4 ohm loads, both channels driven, from 120 – 15,000 Hz; rated 5watts
per channel minimum RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
European model:
DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at
1 kHz, 10% THD)
Music power output (reference): 9 watts + 9 watts
Other models:
DIN power output (rated): 4 watts + 4 watts (4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 5 watts + 5 watts (4 ohms at
1 kHz, 10% THD)
Input
AUDIO IN (stereo mini jack): Sensitivity 550 mV, impedance 50 kilohms
Outputs
PHONES (stereo mini jack): Accepts headphones with an impedance of
8 ohms or more
SPEAKERS: Accepts impedance of 4 ohms
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
*
is output is the value measurement at a distance of 200mm from the
objective lens surface on the Optical Pick-up Block with 7mm aperture.
Frequency response: 20 Hz – 20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Sony Corporation
9-889-797-03
2010F05-1
Audio&Video Business Group
©
2010.06
Published by Sony Techno Create Corporation
®
marks
E51
: Chilean and Peruvian models
KR
: Korean model
MX
: Mexican model
SPECIFICATIONS
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
Tuning range:
North American model: 87.5 MHz – 108.0 MHz (100 kHz step)
Other models: 87.5 MHz – 108.0 MHz (50 kHz step)
Antenna: FM lead antenna
Intermediate frequency: 225 kHz
AM tuner section:
Tuning range
European model:
531 kHz – 1,602 kHz (9 kHz step)
North American, E2, E51 and MX models:
530 kHz – 1,710 kHz (10 kHz step)
531 kHz – 1,710 kHz (9 kHz step)
Australian model:
531 kHz – 1,710 kHz (9 kHz step)
530 kHz – 1,710 kHz (10 kHz step)
SP, TW, KR, TW and TH models:
531 kHz – 1,602 kHz (9 kHz step)
530 kHz – 1,610 kHz (10 kHz step)
Antenna: AM loop antenna
Intermediate frequency: 53 kHz
iPod section
Compatible iPod models:
iPod nano
5th generation
(video camera)
HCD-FX300i
Model Name Using Similar Mechanism
Base Unit Name (US, CND, UK, SP, TW, KR, TH, AUS)
Base Unit Name (AEP, E2, E51, MX)
Optical Pick-up Block Name
SP
: Singapore model
TH
: Thai model
TW
: Taiwan model
iPod classic
iPod touch
120 GB
2nd generation/
160 GB (2009)
iPod touch
Late 2009
COMPACT DISC RECEIVER
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
NEW
BU-D1BD73
BU-D1BD73U
DA11MMVGP
iPod nano
iPod classic
4th generation
iPod touch
160 GB (2007)
(video)
1st generation
iPod nano
3rd generation
iPod nano
iPod classic
(video)
2nd generation
80 GB
(aluminum)
iPod nano
iPod
iPod
1st generation
5th generation
4th generation
(video)
(color display)
iPod mini
iPod
4th generation
– Continued on next page –

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-FX300i US

  • Page 1 5th generation iPod touch 120 GB (video camera) 2nd generation/ Dynamic range: More than 90 dB 160 GB (2009) iPod touch Late 2009 COMPACT DISC RECEIVER Sony Corporation 9-889-797-03 2010F05-1 Audio&Video Business Group © 2010.06 Published by Sony Techno Create Corporation...
  • Page 2 This appliance is classifi ed as TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE a CLASS 1 LASER product. PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- This marking is located on the NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS rear exterior.
  • Page 3: Table Of Contents

    HCD-FX300i Ver. 1.1 TABLE OF CONTENTS SERVICING NOTES 5-8. Schematic Diagram - MAIN Section (2/2) - ....21 ..........5-9. Printed Wiring Boards - MAIN Section - ....... 22 5-10. Printed Wiring Board - IP Board - ........23 DISASSEMBLY 5-11.
  • Page 4: Servicing Notes

    HCD-FX300i Ver. 1.2 SECTION 1 SERVICING NOTES MODEL IDENTIFICATION NOTES ON HANDLING THE OPTICAL PICK-UP - Back Panel - BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static break-down because of the potential difference generated by the charged electrostatic load, etc.
  • Page 5 HCD-FX300i Ver. 1.1 CAPACITOR ELECTRICAL DISCHARGE PROCESSING When checking the board, the electrical discharge is necessary for the electric shock prevention. Connect the resistors referring to the fi gure below. • PT board (C905) (Except 120V AC area in E, Chirean and Pe- ruvian models only) •...
  • Page 6: Disassembly

    HCD-FX300i SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. PANEL (REAR) BLOCK (Page 6) 2-3. TOP PANEL BLOCK (Page 7) 2-7. BASE UNIT 2-4. FRONT PANEL BLOCK (Page 7) (Page 9) 2-8.
  • Page 7: Top Panel Block

    HCD-FX300i Ver. 1.2 2-3. TOP PANEL BLOCK Note 1: This illustration sees the set from rear side. 7 three claws 8 top panel block 5 claw 5 claw 2 Extend the coating clip. 4 connector Note 2: Coating clip has been deleted (CN914) while producing.
  • Page 8: Knob (Vol)

    HCD-FX300i 2-5. KNOB (VOL) Note: This illustration sees the front panel block from PANEL board side. PANEL board hole 2 knob (VOL) 1 Push the knob (VOL) by flat-head screwdriver. front panel block 2-6. MAIN BOARD 4 two screws (BV3) 7 MAIN board 6 screw (BVTP3 K 8)
  • Page 9: Base Unit

    HCD-FX300i Ver. 1.2 2-7. BASE UNIT Note 1: This illustration sees the top panel block from base unit side. 4 two vibration proof rubbers (green) 1 four floating screws (PTPWH M2.6) 3 two vibration proof rubbers 7 base unit (red) 5 four claws Note 2: Four claws might be fixed by bond.
  • Page 10: Test Mode

    HCD-FX300i Ver. 1.2 SECTION 3 TEST MODE COLD RESET CD/USB POWER MANAGE The cold reset clears all data including preset data stored in the This mode is for switch the CD/USB power supply on/off. Even if memory to initial conditions. Execute this mode when returning this state pulls out AC plug, it is held.
  • Page 11: Electrical Check

    HCD-FX300i SECTION 4 ELECTRICAL CHECK CD SECTION CD FACTORY MODE Note: 1. CD Block is basically constructed to operate without adjustment. Note 1: Do not enter the this mode while any other test mode is in prog- 2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat- ress.
  • Page 12 HCD-FX300i MEMO...
  • Page 29: Diagrams

    HCD-FX300i • IC Block Diagrams – BD73/BD73U Board – IC101 LC786924NT-US-H 78 77 76 75 74 LOW-PASS CLOCK PCM OUTPUT FILTER GENERATOR CONTROL LRSY AUDIO OUTPUT DATACK 8FS DIGITAL FILTER/ CONTROL 1BIT D/A CONVERTER DATA EFMIN 1 TEST1 RFOUT 2 STDATA STREAM CONTROL/ STCK...
  • Page 30 HCD-FX300i IC301 BA5826HFP-E2 VO1(–) D.BUFF VO4(–) VO1(+) D.BUFF LEVEL D.BUFF SHIFT VO4(+) D.BUFF LEVEL SHIFT RESET IN4' THERMAL SHUT-DOWN REGULATOR BIAS TRAP BIAS REGB REGOUT MUTE MUTE IN3' IN2' LEVEL LEVEL SHIFT D.BUFF SHIFT D.BUFF VO3(+) VO2(+) D.BUFF D.BUFF VO3(–) VO2(–) RESETt OPOUT...
  • Page 31 HCD-FX300i IC5001 LV23401V-TLM-H OSC CAP REFERENCE LOCAL POWER STATE DIVIDER OSCILLATOR MANAGEMENT MACHINE TUNING AGC DET SYSTEM SD OUT ST OUT BAND-PASS STEREO STEREO AUDIO DEMODULATOR DE-EMPHASIS FILTER DECODER BLEND AMPLIFIER IMAGE DET ANT CAP 9 10 IC5002 PT2579SN OSCILLATION TEST LOGIC &...
  • Page 32 HCD-FX300i – PANEL Board – IC301 BD3491FS-SE2 IC802 S-80928CNNB-G8YT2G 32 SDA 31 SCL VREF DELAY INPUT 30 FIL CIRCUIT – SELECTOR INPUT 29 GND 4 OUT GAIN 3 CD 28 SDA I2C BUS LOGIC 27 SCL SEL2 BUFFER SEL1 26 VCC VOL1 VOLUME VOL2...
  • Page 33 HCD-FX300i • IC Pin Function Description USB BOARD IC101 LC87F1JJ2AU-SQFP-H (USB CONTROLLER) Pin No. Pin Name Description Not used /RES Reset signal input from the system controller “L”: reset Sub system clock input terminal (32.768 kHz) Not used Sub system clock output terminal (32.768 kHz) Not used VSS1 Ground terminal...
  • Page 34 HCD-FX300i Ver. 1.2 PANEL BOARD IC801 LC87F7DC8AU-QIP-E (SYSTEM CONTROLLER) (US, Canadian, UK, Singapore, Taiwan, Korean, Thai and Australian models) LC87F7DJ2BVU-QIP-E (SYSTEM CONTROLLER) (AEP, 120V AC area in E, Mexican, Chilean and Peruvian models) Pin No. Pin Name Description O-CD-CE Chip enable signal output to the CD-MP3 processor O-CD-M-MUTE Muting signal output to the coil/motor driver O-CD-DO...
  • Page 35 HCD-FX300i Ver. 1.2 Pin No. Pin Name Description VDD3 Power supply terminal (+3.3V) O-iPod_TXD Serial data output to the iPod I-iPod_RXD Serial data input from the iPod Serial data output to the USB controller O-USB_TXD (AEP, 120V AC area in E, Mexican, Chilean and Peruvian models only) Serial data input from the USB controller I-USB_RXD (AEP, 120V AC area in E, Mexican, Chilean and Peruvian models only)
  • Page 36: Exploded Views

    HCD-FX300i Ver. 1.2 SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- : Singapore model they may have some difference from the ample: : Thai model original one. KNOB, BALANCE (WHITE) . . . (RED) : Taiwan model •...
  • Page 37: Top Panel Section

    HCD-FX300i Ver. 1.2 6-2. TOP PANEL SECTION not supplied SW880 (including sled motor, spindle motor) not supplied (spindle motor) not supplied not supplied (sled motor) S001 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1748-697-A BD73 BOARD, COMPLETE 4-171-965-01 SPRING CD (US, CND, UK, SP, TW, KR, TH, AUS)
  • Page 38: Front Panel Section

    HCD-FX300i Ver. 1.2 6-3. FRONT PANEL SECTION not supplied (US, CND, UK, SP, TW, KR, TH, AUS) (AEP, E2, E51, MX) Note: Length has been changed while producing FLEXIBLE FLAT CABLE (15 CORE) (Ref. No. 111). Exchange it for the parts of the same length when replacing FLEXIBLE FLAT CABLE (15 CORE) (US, CND, UK, SP, TW, KR, TH and AUS models only).
  • Page 39: Chassis Section

    HCD-FX300i Ver. 1.2 6-4. CHASSIS SECTION not supplied (POWER-TR board) not supplied (REG board) (AEP, UK, E2, E51, SP, KR, TH, AUS) not supplied F002 T001 not supplied not supplied (US, CND, E2, F001 (PT board: except E2, E51) E51, MX, TW) (PT-SW board: E2, E51) Ref.
  • Page 40: Electrical Parts List

    HCD-FX300i Ver. 1.2 SECTION 7 BD73/BD73U ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS : Singapore model the parts list may be different from the uF: aF : Thai model parts specifi ed in the diagrams or the com- •...
  • Page 41 HCD-FX300i Ver. 1.2 BD73/BD73U MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R120 1-216-833-11 METAL CHIP 1/10W R603 1-218-907-11 METAL CHIP 330K 0.5% 1/10W R121 1-216-833-11 METAL CHIP 1/10W R604 1-216-809-11 METAL CHIP 1/10W R122 1-216-833-11 METAL CHIP 1/10W...
  • Page 42 HCD-FX300i Ver. 1.2 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C940 1-126-964-11 ELECT 10uF C5001 1-164-156-11 CERAMIC CHIP 0.1uF < BAND PASS FILTER > C5002 1-164-156-11 CERAMIC CHIP 0.1uF C5003 1-107-826-11 CERAMIC CHIP 0.1uF FL5001 1-236-711-21 FILTER, BAND PASS...
  • Page 43 HCD-FX300i Ver. 1.2 MAIN PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R260 1-216-817-11 METAL CHIP 1/10W X5002 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz) (AEP, UK) ************************************************************ R261 1-216-833-11 METAL CHIP 1/10W R262 1-216-817-11 METAL CHIP 1/10W A-1749-746-A PANEL BOARD, COMPLETE (US, CND) R365...
  • Page 44 HCD-FX300i Ver. 1.2 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C805 1-107-826-11 CERAMIC CHIP 0.1uF IC801 A-1754-843-A IC LC87F7DJ2BVU-QIP-E (for SERVICE) (AEP, E2, E51, MX) C806 1-107-726-91 CERAMIC CHIP 0.01uF C809 1-165-908-11 CERAMIC CHIP 1uF IC802 6-702-749-01 IC S-80928CNNB-G8YT2G...
  • Page 45 HCD-FX300i Ver. 1.2 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R116 1-216-849-11 METAL CHIP 220K 1/10W R733 1-216-821-11 METAL CHIP 1/10W R120 1-216-833-11 METAL CHIP 1/10W R734 1-216-833-11 METAL CHIP 1/10W R121 1-216-841-11 METAL CHIP 1/10W R735 1-216-825-11...
  • Page 46 HCD-FX300i Ver. 1.2 PANEL POWER-TR PT-SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R885 1-216-833-11 METAL CHIP 1/10W < RESISTOR > R886 1-216-845-11 METAL CHIP 100K 1/10W R915 1-216-833-11 METAL CHIP 1/10W R887 1-216-845-11 METAL CHIP 100K 1/10W R957...
  • Page 47 HCD-FX300i Ver. 1.1 PT-SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FH003 1-533-217-31 FUSE HOLDER D101 6-501-579-01 DIODE MC2837 FH004 1-533-217-31 FUSE HOLDER D102 6-501-579-01 DIODE MC2837 < RELAY > < IC > 0 RY002 1-755-496-11 RELAY IC101...
  • Page 48 HCD-FX300i Ver. 1.2 Ref. No. Part No. Description Remark MISCELLANEOUS ************** 1-834-268-21 WIRE (FLAT TYPE) (16 CORE) 0 56 A-1780-028-A OPTICAL PICK-UP BLOCK (DA11MMVGP) (Including sled motor, spindle motor) 1-452-899-31 MAGNET 1-832-876-21 CABLE, FLEXIBLE FLAT (21 CORE) (EXCEPT AEP, UK) 1-832-886-21 CABLE, FLEXIBLE FLAT (23 CORE) (AEP, UK) 1-832-587-21...
  • Page 49 HCD-FX300i MEMO...
  • Page 50 HCD-FX300i REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2010.03 2010.05 Addition of 120V AC area in E, Mexican, Chilean, Peruvian, Singapore, Taiwan, Korean and Thai models 2010.06...

Table of Contents