BCE FlexStation Venus Overhead Assembly Instructions

WorkZone Corner Desk with Balance Overhead Cabinet
Venus
overhead cabinet
corner
stanchion
#12 x 1 / "
3
screw
Figure 1
Assembly Instructions
FlexStation Corner Desk Overhead Cabinet
grommet
knock-out
#10-32 x ½"
screw
#10-32 x 1"
corner overhead
4
mounting tube
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Venus Overhead
OE-60931/PDF0314
grommet
grommet
knock-out
covers
right-hand
stanchion
screw
#10 x / "
3
screw
Note: Determine if cabinet to be installed is
to be right-hand or left. This instruction
covers right, though left-hand cabinet
Note: Determine if cabinet to be
installation is similar, it will have a different
installed is to be right-hand or left.
set of overhead stanchions.
This instruction covers right, though
left-hand cabinet installation is similar,
Note: WorkZone Corner Desk must be fully
it will have a different set of overhead
installed prior to installing the overhead unit.
stanchions.
1. Begin by removing grommet covers at
Note: FlexStation Corner Desk must be
the rear corner, and side location where the
fully assembled prior to installing the
overhead cabinet will be installed (Figure 1).
overhead unit.
2. At the rear corner, from underneath the
1. Begin by removing grommet covers
corner worksurface, install a corner
at the rear corner, and side location
overhead mounting tube using two #12 x
where the overhead cabinet will be
1-3/4" screws (Figure 1).
installed (Figure 1).
3. Position the corner stanchion (left-hand)
2. At the rear corner, from underneath
as illustrated through the corner grommet
the corner worksurface, install a
hole, aligning the mounting holes in the
corner overhead mounting tube
bracket of the stanchion with the mounting
using two #12 x 1
holes of the corner overhead mounting tube.
(Figure 1).
Secure bracket to tube using two #10-32 x
1/2" screws (Figure1). 3. Position the corner stanchion (left-
hand) as illustrated through the
corner grommet hole, aligning the
4. Position the right-hand stanchion with the
mounting holes in the bracket of the
bracket through the grommet hole, aligning
stanchion with the mounting holes
the mounting holes in the bracket of the
of the corner overhead mounting
stanchion with the mounting holes in the top
tube. Secure bracket to tube using
of the right-hand leg. Secure bracket to leg
4
two #10-32 x
using two #10-32 x 1/2" screws (Figure1).
4. Position the right-hand stanchion
5. Carefully set the Balance Overhead
with the bracket through the
Cabinet onto the two installed stanchions.
grommet hole, aligning the
Align the three sets of mounting holes on
mounting holes in the bracket of
each side of cabinet/stanchion and secure
the stanchion with the mounting
using three #10 x 3/4" screws each side
holes in the top of the right-hand
(Figure 1).
leg. Secure bracket to leg using two
#10-32 x
6. Remove the knock-outs from the
grommet covers removed in step 1, and
5. Carefully set the Venus Overhead
snap them back into place in the grommet
Cabinet onto the two installed
holes at the stanchions (Figure 2).
stanchions. Align the three sets of
mounting holes on each side of
cabinet/stanchion and secure using
three #10 x
(Figure 1).
6. Remove the knock-outs from
the grommet covers removed in
step 1, and snap them back into
place in the grommet holes at the
stanchions (Figure 2).
/ " screws
3
4
/ " screws (Figure 1).
1
2
/ " screws (Figure 1).
1
2
/ " screws each side
3
4