Nokia 2228Arte Service Manual

Mobile terminal

Table of Contents

Quick Links

Download this manual

Nokia Customer Care

Service Manual

RM-377 (Nokia 2228Arte; L3&4)

Mobile Terminal

Part No: (Issue 2)

COMPANY CONFIDENTIAL

Table of Contents

Chapters

Table of Contents

Troubleshooting

Summary of Contents for Nokia 2228Arte

Page 2 Version 0.3 2009.01.19 Michelle Wang Update version Version 0.4 2009.01.21 Michelle Wang Update version Version 0.5 2009.02.03 Michelle Wang Update version Version 0.6 2009.02.17 Michelle Wang Update version Page ii COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 3 Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
Page 4 WCDMA networks and cause problems to 3G cellular phone communication in a wide area. During testing never activate the GSM or WCDMA transmitter without a proper antenna load, otherwise GSM or WCDMA PA may be damaged. Page iv COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 5 Use only approved accessories and batteries. Do not connect incompatible products. CONNECTION TO OTHER DEVICES When connecting to any other device, read its user’s guide for detailed safety instructions. Do not connect incompatible products. Issue 1 COMPANY CONFIDENTIAL Page v Copyright © 2008 Nokia. All rights reserved.
Page 7 ESD protection ESD protection Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.
Page 8 Batteries' performance is particularly limited in temperatures well below freezing. Do not dispose of batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. Page viii COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 9 While every endeavor has been made to ensure the accuracy of this document, some errors may exist. If any errors are found by the reader, NOKIA MOBILE PHONES Business Group should be notified in writing/e-mail. Please state: Title of the Document + Issue Number/Date of publication...
Page 11 Nokia 2228Arte Service Manual Structure 1. General information 2. Service Devices and Service Concepts 3. BB Troubleshooting and Manual Tuning Guide 4. RF Troubleshooting 5. System Module Description Glossary Issue 1 COMPANY CONFIDENTIAL Page xi Copyright © 2008 Nokia. All rights reserved.
Page 15: Table Of Contents
Table of Contents Product selection…………………………………………………………………………………………………………………………………….…..1-5 Phone features……………………………………………………………………………………………………………………………….……….…..1-5 User interface and software features……………………………………………………………………………………………….……….…..1-6 Accessories……………………………………………………………………………………………….…………………………………………….…..1-6 Technical specifications……………………………….…………………………………………….…………………………………………….…..1-6 General specifications…………………………….…………………………………………….…………………………………………….…..1-6 Battery endurance…………………………………….………………………………………….…………………………………………….…..1-6 List of Figures Figure 1 RM-377 (Nokia 2228Arte) product picture………………………………………………………………………………….…..1-5 Issue 1 COMPANY CONFIDENTIAL Page 1-3 Copyright © 2008 Nokia. All rights reserved.
Page 17: Product Selection
RM-377 General information Product selection RM-377 (Nokia 2228) is a CDMA200 single band phone, supporting CDMA2000 1xRTT /Cell/PCS/AWS bands. Figure 1 RM-377 (Nokia 2228Arte) product picture Phone features Display and keypad features 1.8” 128x160 pixel, 262k true color internal display...
Page 18: User Interface And Software Features
NMP Standby time BL-4C 860mAh Li-Ion battery Up to 3.5 hours 10 days Note: The variation in operation times will occur depending on network parameters, phone setting and usage. Page 1-6 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 22: Table Of Contents
POS (Point of Sale) flash concept…………………………………………………………………………...........2-8 SW download….………………………………………………………………………………………………...........2-9 Introduction……………………………………………..………………………………………………............2-9 Operation guide……………………...........................2-9 Single bundle download tool ............................2-9 Multi bundle download tool ............................2-10 Single download tool ..............................2-12 Dead phone revive tool ..............................2-13 Issue 0.3 COMPANY CONFIDENTIAL Page 2-3 Copyright © 2008 Nokia. All rights reserved.
Page 24: Service Devices
Dongle This device (“dongle”) is required when using the Level 3 service software. It has a USB connector. This dongle is not interchangeable with existing Nokia dongles. Issue 0.3 COMPANY CONFIDENTIAL Page 2-5 Copyright © 2008 Nokia. All rights reserved.
Page 25: Cables
• PCS band: 0.8+-0.1 dB • AWS band: 1+-0.1dB CA-128RS RF cable The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment. Page 2-6 COMPANY CONFIDENTIAL Issue 0.3 Copyright © 2008 Nokia. All rights reserved.
Page 26 RM-377 Service Devices and SW Update XRS-6 RF cable The RF cable is used to connect, for example, a module repair jig to the RF measurement equipment. Issue 0.3 COMPANY CONFIDENTIAL Page 2-7 Copyright © 2008 Nokia. All rights reserved.
Page 27: Pos (Point Of Sale) Flash Concept
POS (Point of Sale) flash concept Type Description Product specific tools BL-4C Battery Other tools PK-85 USB dongle PC with PST software Cables CA-101 USB connectivity cable Page 2-8 COMPANY CONFIDENTIAL Issue 0.3 Copyright © 2008 Nokia. All rights reserved.
Page 28: Introduction
Make sure the COM port number on the left-bottom un-edit field is the same as you see from device manager then click “FLASH” button to start downloading. Issue 0.3 COMPANY CONFIDENTIAL Page 2-9 Copyright © 2008 Nokia. All rights reserved.
Page 29: Multi Bundle Download Tool
Make sure the COM port numbers in front of each progress bar can also be seen in device manager. Mark the selection button in front of each COM port number field to programme the phone connected to this port. Click “FLASH” button to start downloading Page 2-10 COMPANY CONFIDENTIAL Issue 0.3 Copyright © 2008 Nokia. All rights reserved.
Page 30 It’s an option that formats the phone file system without User Data backup/restore Format EFS during downloading. It’s an option that checks connected battery level before downloading images into Check Battery phone to protect downloading procedure. Issue 0.3 COMPANY CONFIDENTIAL Page 2-11 Copyright © 2008 Nokia. All rights reserved.
Page 31: Single Download Tool
It’s an option that formats the phone file system without User Data backup/restore Format EFS during downloading. It’s an option that checks connected battery level before downloading images into Check Battery phone to protect downloading procedure. Page 2-12 COMPANY CONFIDENTIAL Issue 0.3 Copyright © 2008 Nokia. All rights reserved.
Page 32: Dead Phone Revive Tool
“Format EFS” selection button or not. It’s an option that checks connected battery level before downloading images into Check Battery phone to protect downloading procedure. Issue 0.3 COMPANY CONFIDENTIAL Page 2-13 Copyright © 2008 Nokia. All rights reserved.
Page 36 Vibrator Failure………………………………………………………………………………………………………………..……………….……3-35 Speaker Failure………………………………………………………………………………………………………………..……………………3-37 Receiver Unit (speaker & key tone) ……………………………………………………………………………………..……….…………3-39 UIM Card failure………………………………………………………………………………………………………………..……………………3-41 FM Failure………………………………………………………………………………………………………………..…………………………….3-43 Camera failure………………………………………………………………………………………………………………………………….……3-45 List of Figures Figure 2 High-level power sequences timing diagram…………………………………………………………………………..……3-25 Issue 1 COMPANY CONFIDENTIAL Page 3-3 Copyright © 2008 Nokia. All rights reserved.
Page 38: Placement-Main (Key-Pad Side)
RM-377 BB Troubleshooting and Manual Tuning Guide Placement - Main (Key-pad side) Top view Key LED: D920~ D925 AOT-0603W331A Side view indicator LED: D1100 AELWU-D Issue 1 COMPANY CONFIDENTIAL Page 3-5 Copyright © 2008 Nokia. All rights reserved.
Page 40: Circuit-Qsc6030 Memory And Lcd Interface
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit–QSC6030 memory LCD interface Issue 1 COMPANY CONFIDENTIAL Page 3-7 Copyright © 2008 Nokia. All rights reserved.
Page 41: Circuit-Qsc6030 Lcd Interface
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit-QSC6030 LCD interface Page 3-8 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 42: Circuit-Qsc6030 Charge Function
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit–QSC6030 charge function Issue 1 COMPANY CONFIDENTIAL Page 3-9 Copyright © 2008 Nokia. All rights reserved.
Page 44: Circuit-Qsc6030 Battery Supplier
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit–QSC6030 battery supplier Issue 1 COMPANY CONFIDENTIAL Page 3-11 Copyright © 2008 Nokia. All rights reserved.
Page 46: Circuit-Qsc6030 Peripheral Interface
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit–QSC6030 peripheral interface Issue 1 COMPANY CONFIDENTIAL Page 3-13 Copyright © 2008 Nokia. All rights reserved.
Page 51: Circuit-Acoustic Interface Part 1 (Through Melody Ic To Provide)
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit–Acoustic interface Part 1 (through Melody IC to provide) Page 3-18 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 56: Circuit-Lanyard Indicator Led
RM-377 BB Troubleshooting and Manual Tuning Guide Circuit– Lanyard indicator LED Issue 1 COMPANY CONFIDENTIAL Page 3-23 Copyright © 2008 Nokia. All rights reserved.
Page 58: Troubleshooting For Bb Part
Voltage regulators turned on in a sequence. PON_RESET_N pin high. PS_HOLD pin high e. Check SW code version (or re-download SW code again) Figure 2 High-level power sequences timing diagram Issue 1 COMPANY CONFIDENTIAL Page 3-25 Copyright © 2008 Nokia. All rights reserved.
Page 60: Lcd B/L On/Off Failure
(disassemble LCM from PCB and test by Diode mode of meter) d. Check the resistance of LCD_DRV_N pin, it shall be not open (bigger than 10M ohm). Issue 1 COMPANY CONFIDENTIAL Page 3-27 Copyright © 2008 Nokia. All rights reserved.
Page 61: Key B/L On/Off Failure
(The diode mode of meter can test LED path is good or not ; TP901 is positive and TP900 is negative) b. Check the resistance of KPD_DRV_N pin, it shall be not open (bigger than 10M ohm). c. Check TP901, it shall be connect BATT_VDD (C314) directly. Page 3-28 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 62: Key Pad Failure
Check the resistance of key scan pin, each pin of matrix shall be 5M to 10M ohm c. Check scan signal sequence, each pulse of row of scan is around 51uS. (the first : kypd_17, the last : kypd_9). Issue 1 COMPANY CONFIDENTIAL Page 3-29 Copyright © 2008 Nokia. All rights reserved.
Page 64: Lcd Failure
Change a working part to confirm QSC6030 control path is ok or not. d. The control line of RESX (J1200.17) shall be keep to High (2.6V) after system turn-on. d. Check power supply voltage shall be 2.9V (VREG_MSME2) Issue 1 COMPANY CONFIDENTIAL Page 3-31 Copyright © 2008 Nokia. All rights reserved.
Page 66: Microphone Failure
Check MIC_BAS has 2V output when system in echo mode. d. Check connections or solder connections on R609, R610, R611, C610 and C612. c. Check QSC6030 to check main chip issue. Issue 1 COMPANY CONFIDENTIAL Page 3-33 Copyright © 2008 Nokia. All rights reserved.
Page 68: Vibrator Failure
Check the gold pad of vibrator not have any damage. e. Check the rate voltage of Vibrator shall be satisfy 1.3V. If failure, please change a new QSC6030. (VIB_DRV_V failure) Issue 1 COMPANY CONFIDENTIAL Page 3-35 Copyright © 2008 Nokia. All rights reserved.
Page 70: Speaker Failure
Check R715 has a 24MHz clock signal when melody playing. If not, QSC6030 failure e. Has ring tone playing by speaker on system turn-on? If not, melody IC failure. (U700) Issue 1 COMPANY CONFIDENTIAL Page 3-37 Copyright © 2008 Nokia. All rights reserved.
Page 72: Receiver Unit (Speaker & Key Tone)
Check R807 and R08 were soldering well and resistance is normal. (4.7R_1%) d. Check C616 have damage or not. (Short phenomenon) e. Change a QSC6030 to confirm main chip failure. Issue 1 COMPANY CONFIDENTIAL Page 3-39 Copyright © 2008 Nokia. All rights reserved.
Page 74: Uim Card Failure
Check J600 pin-2 shall be keep to 2.6V once system turn-on. e. Check J600 pin-3 shall be have 2.4MHz clock input. f. Change a QSC6030 to confirm main chip failure. Issue 1 COMPANY CONFIDENTIAL Page 3-41 Copyright © 2008 Nokia. All rights reserved.
Page 76: Fm Failure
Check R1308, C1300 soldering is good? f. Check FM Ant path, any solder issue on R1308, L1301, C1300 and L800. h. Change a new FM chip if there are not above issue. Issue 1 COMPANY CONFIDENTIAL Page 3-43 Copyright © 2008 Nokia. All rights reserved.
Page 78: Camera Failure
Check J1203 pin-12 has 24MHz(2.5V) input clock and pin-1 has 24MHz(2.6V) output clock. If not, change a new CCM to confirm module. e. CCM initial failure shall be check U1202 and J1202 dering. Issue 1 COMPANY CONFIDENTIAL Page 3-45 Copyright © 2008 Nokia. All rights reserved.
Page 83 General instructions for transmitter (TX) Troubleshooting..................4-10 Wireless troubleshooting…………………………..………………………...................4-11 General instructions for wireless Troubleshooting……………………..………..............4-11 List of Figures Figure 3 RF key components…………………..………………………………………………..…………………………..……………………...4-7 Figure 4 Tuning concept with CMU200………………………………………………..………………………..…………….………………...4-8 Issue 1 COMPANY CONFIDENTIAL Page 4-3 Copyright © 2008 Nokia. All rights reserved.
Page 85: Rf Self Tests In The Calibration And Test Tool
RF self tests in the calibration and test tool Context Always start the troubleshooting procedure by running the calibration and test tool. If a test fails, please follow the diagram below. Troubleshooting flow Issue 1 COMPANY CONFIDENTIAL Page 4-5 Copyright © 2008 Nokia. All rights reserved.
Page 86: Troubleshooting
Please refer to the list of Non replaceable RF components. Note: If the RF shielding can is removed (for measurement or repair), it must always be replaced with a new one. Page 4-6 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 88: Hardware Set Up
1. Set up the main board. The phone should be in FTM mode. 2. Check the following: Signal name Test point Voltage VREG_TCXO R1016 2.85V BATT_VDD R1013 3.85V VREG_RFRX C1004 2.6V VREG_RFTX R401 2.6V Page 4-8 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 89: Receiver Troubleshooting
Make the following settings in Qualcomm software and in the signal generator. Band 0 Setting Channel Signal generator to antenna connector 881.52 MHz CDMA RX calibration fails in the VGA offset troubleshooting Cellular band Issue 1 COMPANY CONFIDENTIAL Page 4-9 Copyright © 2008 Nokia. All rights reserved.
Page 90: Transmitter Troubleshooting
RF connector (antenna, RF-measurement equipment or at least a 2 W dummy load); otherwise the CDMA Power amplifier (PA) may be damaged. Cellular band Page 4-10 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 91: Wireless Troubleshooting
RF connector (antenna, RF-measurement equipment or at least a 2 W dummy load); otherwise the CDMA Power amplifier (PA) may be damaged. Cellular band Issue 1 COMPANY CONFIDENTIAL Page 4-11 Copyright © 2008 Nokia. All rights reserved.
Page 95 Environmental conditions……………………………………………………………………………………………………….…….………..5-14 List of Tables Table 1 Nominal voltages……………………………………………………………………………………….……………….…….………..5-10 List of Figures Figure 5 Main board, top side………………………………………………………………………………….…………….…….………….5-8 Figure 6 Battery pin order……………………………………………………………………………………….…………….…….………….5-9 Figure 7 Battery connector………………………………………………………………………………..…….…………….…….………….5-9 Issue 1 COMPANY CONFIDENTIAL Page 5-3 Copyright © 2008 Nokia. All rights reserved.
Page 97: Introduction
Phone description QSC6030 is the single-chip device baseband ASIC in the phone. It contains functionality for RF, MSM, and PM ICs. System block introduction QSC6030 System Module Description. Issue 1 COMPANY CONFIDENTIAL Page 5-5 Copyright © 2008 Nokia. All rights reserved.
Page 98: Phone Key Components And Placement
CNO-5225-3028H 3P 3.1P YOKOWO J301 Micro-USB connector ZX62D1-B-5PA 5PIN 0.65 HIROSE J300 Current fuse 046701.5 1.5A 32V 0603 LITTEL F300 LCM connector FH26W-23S-0.3SHW(05) 23P HRS J1200 Antenna A1000, A1001 Page 5-6 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 101: Energy Management
This phone is charged through the µUSB interface only (there is no separated connector for a charger), Support two charging mode for normal USB charging and two approved NOKIA chargers(AC-6 and DC-6) charging, Charging is controlled by energy management, and external components are needed to protect the baseband module against EMC, reverse polarity and transient frequency deviation.
Page 102: Normal And Extreme Voltages
µUSB. VBUS User interface Display In this phone, support display for l LCD TFT Transflective1.77””, in the system, Display controller via EBI2 8bit data bus. Page 5-10 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 103: Backlight And Illumination
2 analog input ( Handset and Headset Microphone ) 1 earpiece for handset For Melody IC 2 analog input I2S interface Stereo headphone output AB-class speaker amplify output Figure 10 Audio block diagram Issue 1 COMPANY CONFIDENTIAL Page 5-11 Copyright © 2008 Nokia. All rights reserved.
Page 104: Internal Audio
The transmitter functions are implemented in the QSC6030 RF block. Even though the CELL/ signals are sent via different components, the principles of the transmission are the same. QSC6030 System Module Description Page 5-12 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 105 System Module Description Support FM non-RDS, I2C is control bus from QSC6030, Line-up signal provide a analogue signal to CODEC IC Output music to ear-piece or loud speaker Issue 1 COMPANY CONFIDENTIAL Page 5-13 Copyright © 2008 Nokia. All rights reserved.
Page 106: Technical Specifications
Condensed or dripping water may cause intermittent malfunctions. Humidity and Water Protection against dripping water Resistance has to be implemented (enclosure) mechanics. Continuous dampness will cause permanent damage to the module. Page 5-14 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 110 Clock Timing Sleep and interrupt block of Tiku Continuous wave D/A-converter Digital-to-analogue converter Digital-to-analogue converter Digital Battery Interface DBus DSP controlled serial bus connected between UPP_WD2 and Helgo DCT-4 Digital Core Technology Issue 1 COMPANY CONFIDENTIAL Page Glossary-3 Copyright © 2008 Nokia. All rights reserved.
Page 111 High speed circuit switched data (data transmission connection faster than GSM) Hardware Input/Output IBAT Battery current Integrated circuit ICHAR Charger current Interface Integrated hands free IMEI International Mobile Equipment Identity Infrared IrDA Infrared Data Association Page Glossary-4 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 112 General Purpose IO (PIO), USARTS and Pulse Width Modulators PURX Power-up reset Printed Wiring Board Pulse width modulation RC-filter Resistance-Capacitance filter Radio Frequency PopPort™ Reduced function PopPort™ interface RFBUS Serial control Bus For RF Issue 1 COMPANY CONFIDENTIAL Page Glossary-5 Copyright © 2008 Nokia. All rights reserved.
Page 113 Communicator version of DCT4 system ASIC Universal Serial Bus VBAT Battery voltage VCHAR Charger voltage Voltage controlled oscillator VCTCXO Voltage Controlled Temperature Compensated Crystal Oscillator VCXO Voltage Controlled Crystal Oscillator Page Glossary-6 COMPANY CONFIDENTIAL Issue 1 Copyright © 2008 Nokia. All rights reserved.
Page 114 Wideband code division multiple access Watchdog WLAN Wireless local area network XHTML Extensible hypertext markup language Zocus Current sensor (used to monitor the current flow to and from the battery) Issue 1 COMPANY CONFIDENTIAL Page Glossary-7 Copyright © 2008 Nokia. All rights reserved.

This manual is also suitable for:

Rm-377

Nokia 2228Arte Service Manual

Table of Contents

(This Page Left Intentionally Blank.)

Table of Contents

(This Page Left Intentionally Blank.)

Table of Contents

Quick Links

Chapters

Troubleshooting

Related Manuals for Nokia 2228Arte

Summary of Contents for Nokia 2228Arte

This manual is also suitable for:

Table of Contents