Page 2
www.reelschematic.com www.reelschematic.com Y o u r L o c a l A g e n t / D e a l e r 9 - 5 2 , A s h i h a r a - c h o , N i s h i n o m i y a , J a p a n T e l e p h o n e : 0 7 9 8 - 6 5 - 2 1 1 1...
"WARNING" and "CAUTION" notices appear throughout this manual. It is the responsibil- ity of the installer of the equipment to read, understand and follow these notices. If you have any questions regarding these safety instructions, please contact a FURUNO agent or dealer.
Page 4
www.reelschematic.com www.reelschematic.com CAUTION WARNING Ground the equipment to Do not work inside the prevent electrical shock equipment unless totally and mutual interference. familiar with electrical circuits. Confirm that the power supply voltage Hazardous voltage which can is compatible with the voltage rating shock, burn or cause serious of the equipment.
www.reelschematic.com www.reelschematic.com 3. Mounting Mounting Guidelines The main unit and terminal unit are designed for tabletop mounting. They may be installed almost anywhere provided the location satis- fies the following conditions: ¡The ambient temperature range is -15 to +55;. ¡For the terminal unit, select a place where the keyboard can be easily operated while viewing the display screen.
Page 13
www.reelschematic.com www.reelschematic.com Terminal Unit 1. Fix the hanger to the table with four tapping screws, referring to outline drawing on page D-2. 2. Attach connectors to bottom panel. (See next page) 3. Set the terminal unit to the hanger with two knobs. 4.
www.reelschematic.com www.reelschematic.com 4. Wiring CAUTION Ground the equipment to prevent electrical shock and mutual interference. Confirm that the power supply voltage is compatible with the voltage rating of the equipment. Connection to the wrong power supply can cause fire or equipment damage. The voltage rating appears on the label at the rear of the display unit.
www.reelschematic.com www.reelschematic.com 5. Initial Setting Answerback Code & ID Code Enter vessel’s answerback code and ID code as follows. NOTE The answerback and ID code number can be written only once; be sure to enter the codes correctly. Answerback Code Procedure 1.
Page 16
www.reelschematic.com www.reelschematic.com 3. For final verification of the data, the above CAUTION appears. If correct, press the ENTER key again. NOTE: Form of answerback depends on coast statiton. Some re- quest ship name and/or callsingn. ID Code Procedure 1. Press function key F5 and then the [6], [7], [8] or [9] key to enter the Group ID Code (4 or 5 digits), Group ID Code (9 digits), Se- lect ID Code (4/5 digits) or Select ID Code (9 digits), respectively.
Page 17
www.reelschematic.com www.reelschematic.com System Settings Press function key F6 to display the System screen. System Setup Lock Change Default *Slave Delay 5 msec (0- 50 msec) *BK Timing PreTone 10 msec (0-100 msec) PoseTone 0 msec (0- 20 msec) *Mute Timing PreBK 0 msec (0- 20 msec) PostBK 0 msec (0- 20 msec)
Page 18
14. Modem Output Level Adjusts output signal from the modem, be- tween -30 and +10 dBm. Refer to operation’s manual of radiotelephone connected. With FURUNO radiotelephone, the default set- ting is available. MIF Command Tune* With FURUNO transmitter connected, ON sends antenna coupler tuning command.
Page 19
MUTE TIMING PRE BK MUTE TIMING POST BK Timing values depend on the transceiver connected. Therefore some trial and error may be necessary to find suitable values. Default values are for FURUNO SSB Radiotelephone model FS-1500 or FS-1562. Setting of Timing FS-1500 series...