Summary of Contents for SAINTFINE SF-XDCD
- Page 1 Operation Manual Battery Powered ULV Cold Fogger （Electrostatic type） SF-XDCD(751)
- Page 3 Dear customer, Thank you for choosing our electrostatic battery powered ULV cold fogger. Please read the operation manual carefully before use and strictly follow the safety instruction to prevent product malfunctions that affect your normal use or cause unnecessary losses. We hope that you can read this operation manual to operate our product safely, correctly and efficiently, maintain the best operating condition of the product, so as to improve the efficiency of the product.
-
Page 4: Table Of Contents
Illustrated parts ............3 Technical parameters ..........4 Basic working principle ........5 Operation instructions ......... 5 Battery usage and maintenance ..... 7 Common failures and troubleshooting ..8 Cautions ..............9 VIII Warranty service ..........10 Packing list .............. 12... -
Page 5: I Illustrated Parts
Ⅰ Illustrated parts 1.air duct 2. shell 3.charging port... -
Page 6: Technical Parameters
4.spout plug 5. cap 6. tank 7.bottom shell 8. static electricity 9.power adapter 10.belt 11. battery 12.ground contact pad 13. rocker switch 14.Electrostatic bracelet Ⅱ Technical parameter Model SF-751 Parameter Rated Voltage DC24V... - Page 7 Rated power 240W Spray volume 80-150ml/min Droplet size ＜50μm Spray distance 5-8m (calm wind) Working time 50-60mins Machine size 640*130*225mm （L×W×H）...
-
Page 8: Basic Working Principle
Ⅲ Basic working principle The electrostatic battery powered ULV cold fogger use high-power super speed brushless DC motor, the high speed motor can drive the fan blade to produce high-speed rotating air, meanwhile, the liquid is delivered to the micro nozzle with constant flow rate and high speed air flow, under the action of high-speed rotating air and special structure of nozzle, the liquid is broken into tiny droplets. - Page 9 Booting process: 1) Firstly, hold the contact piece and wear the electrostatic bracelet. 2) Secondly, turn on round button switch on the right side. 3) Thirdly, switch on the red electrostatic button.
-
Page 10: Battery Usage And Maintenance
4) When finish the work, turn off the red button first, then move the hand from the contact piece, and take off the bracelet, the switch off the round button. 5) After spraying the liquid, first clean the residual liquid in the tank with clean water, pour it out, and then add a small amount of clean water to spray for 1-2 minutes, to prevent the liquid from clogging or corroding the nozzle and pipes. - Page 11 off to ensure the shutdown state when charging; the machine should be placed stably when charging, and the charger plug must be charged with the side of the machine connect the interface, continue charging until the indicator light turns green; the charging time is 5-6 hours.
- Page 12 Ⅵ Common faults analysis and trouble shooting 1. Fault phenomena: the motor does not run. Analysis: (1) The battery power is not enough. Trouble shooting: Check if the rocker switch is open. Restart the machine to test after charging the battery. (Refer to V.1.) Analysis: (2) Overload operation and protection device works.
-
Page 13: Cautions
the nozzle. Troubleshooting: Please contact our company to guide the installation Ⅶ Cautions 1. The battery should be charged completely before using. 2. If the liquid goes inside the machine, please wait for it to dry completely before turning on it. 3. - Page 14 occur during use: 1) Water enters inside the machine; 2) The motor suddenly stops running; 3) The sound of the motor has changed significantly; 4) Leaking liquid in the tank; 5) The motor does not rotate or other abnormal conditions when starting. 8.
-
Page 15: Warranty Service
Ⅷ Warranty Service 1. One-year warranty is provided for the main components of the machine List of major components: 1) Motor 2) Electronic control board 3) Battery (warranty for liquid leakage, plastic shell cracking, etc. Except for human factors and external damage, water enters into the battery bottom.) 4) Power adapter 5) Tank... -
Page 16: Packing List
2. The below circumstances are not included in the warranty service: 1) The blockage and damage of equipment because of using strong corrosive liquid. 2) The faults or damage because of manipulating the structure and replacing the parts of equipment without authorization. 3) Not following the instructions of use and maintenance. - Page 17 Charger DC24V 1.8A Screwdriver Belt Sponge 0.8mm 0.8mm＜40μm 1.0mm Nozzles (Installed on 1.0mm＜60μm the machine) 1.5mm＞60μm 1.5mm O-ring 8.5*1.8 mm Operation manual Electrostatic bracelet...