Acer Chromebook CP713-3W Lifecycle Extension Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Laptop
  5. Chromebook CP713-3W
  6. Lifecycle extension manual

Acer Chromebook CP713-3W Lifecycle Extension Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Acer Chromebook CP713-3W
LIFECYCLE EXTENSION
GUIDE

Advertisement

Table of Contents
loading

Related Manuals for Acer Chromebook CP713-3W

Summary of Contents for Acer Chromebook CP713-3W

  • Page 1 Acer Chromebook CP713-3W LIFECYCLE EXTENSION GUIDE...
  • Page 2 Self-Repair ..........1-1 Disassembly Procedures .
  • Page 3 NOTE: NOTE: Do not attempt to replace other components than those listed above. NOTE: NOTE: For replacement parts, always use only Acer certified components in order to safeguard quality, optimum system performance, stability and reliability of the product. NOTE: NOTE:...
  • Page 4 NOTE: NOTE: System BIOS upgrades or downgrades, if not performed by an Acer Service Center or authorized Service Partner, are at own risk. To update Drivers: Run Windows Update in order to get the latest drivers from Acer:...
  • Page 5 Disassembly Procedures Safety Guidelines This chapter contains step by step procedures on how to remove and de-install components from the computer. Use the following safety guidelines to ensure your personal safety. Each procedure included in this chapter assumes that you are preparing your computer for recycling and disposal.
  • Page 6 WEEE Annex VII Component These components are classified as requiring selective treatment: Battery pack  Touchpad module  SSD module  USB board  Mainboard  LCD panel  Disassembly Procedures...
  • Page 7 Pre-disassembly Instructions Do the following prior to starting any maintenance procedures: 1. Place the system on a stable work surface. 2. Remove the power adapter from the USB Type-C port (A or B) as shown in Figure 1-1. 3. Remove all cables from system. Figure 1-1.
  • Page 8 Base Cover Removal 1. Remove nine (9) screws from the base cover (Figure 1-3). Figure 1-3. Base Cover Removal 2. Carefully pry up the base cover starting from the upper right edge side to release the latches. Then continue releasing the remaining latches on the upper, left, right, and bottom sides (Figure 1-4).
  • Page 9 3. Grasp and remove the base cover from the system (Figure 1-5). Figure 1-5. Base Cover Removal Disassembly Procedures...
  • Page 10 Battery Pack Removal Prerequisite: Base Cover Removal 1. Find the battery pack (A) on the top assembly (Figure 1-6). 2. Detach the tape (B) securing the battery cable to the mainboard connector (Figure 1-6). 3. Detach the transparent mylar (C) securing the battery cable and keyboard FPC (Figure 1-6).
  • Page 11 4. Disconnect the battery cable from the mainboard connector (D) (Figure 1-7). Figure 1-7. Battery Pack Removal 5. Remove the battery pack from the top assembly (Figure 1-8). WEEE Annex VII Component: Battery Pack Figure 1-8. Battery Pack Removal IMPORTANT: Follow local regulations for battery disposal.
  • Page 12 Touchpad Module Removal Prerequisite: Battery Pack Removal 1. Disconnect the keyboard FPC from the mainboard connector (A) (Figure 1-9). Figure 1-9. Touchpad Module Removal 2. Disconnect the touchpad FFC (B) from the touchpad module and mainboard connectors. Then remove the touchpad FFC from the top assembly (Figure 1-10).
  • Page 13 3. Gently peel off the conductive tape (C) to detach it from its designated slot on the touchpad module and top assembly (Figure 1-11). Figure 1-11. Touchpad Module Removal 4. Remove three (3) screws securing the touchpad module in place (Figure 1-12).
  • Page 14 5. Using the screwdriver, push the guide pins (D) firmly to release them from the top assembly (Figure 1-13). 6. With one hand is placed underneath the touchpad module, push the touchpad module slightly to disengage it from the bottom latches (E), and then remove the touchpad module (F) from the top assembly (Figure 1-13).
  • Page 15 SSD Module Removal Prerequisite: Battery Pack Removal 1. Disconnect the 45-pin USB board FFC from the USB board connector (A) and the mainboard connector (B). Then remove the 45-pin USB board FFC (Figure 1-14). Figure 1-14. SSD Module Removal 2. Remove one (1) screw securing the SSD module in place (Figure 1-15).
  • Page 16 3. Remove the SSD module (C) from the mainboard connector (D) (Figure 1-16). WEEE Annex VII Component: SSD Module Figure 1-16. SSD Module Removal 1-14 Disassembly Procedures...
  • Page 17 LCD Module Removal Prerequisite: Battery Pack Removal 1. Disconnect the G-sensor cable from the USB board connector (A) (Figure 1-17). 2. Unroute the G-sensor cable from the cable guide (B) (Figure 1-17). Figure 1-17. LCD Module Removal 3. Disconnect the eDP cable from the mainboard connector (C) (Figure 1-18).
  • Page 18 4. Remove six (6) screws securing the LCD hinges in place (Figure 1-19). Figure 1-19. LCD Module Removal 5. Lift the top assembly until it is fully open (Figure 1-20). Figure 1-20. LCD Module Removal 1-16 Disassembly Procedures...
  • Page 19 6. Close the top assembly and lift both LCD hinges until they are fully extended (Figure 1-21). Figure 1-21. LCD Module Removal 7. Open the top assembly again. Then remove the LCD module away from the top assembly (Figure 1-22). Figure 1-22.
  • Page 20 USB Board Removal Prerequisite: Ensure that the Fan has been disassembled prior removing the USB board. 1. Remove three (3) screws (A) securing the left side of LCD hinge in place (Figure 1-23). Figure 1-23. USB Board Removal 2. Lift the top assembly until it is fully open (Figure 1-24).
  • Page 21 3. Close the top assembly and lift the left side of LCD hinge until it is fully extended (Figure 1-25). Figure 1-25. USB Board Removal 4. Disconnect the 40-pin USB board FFC (B) from the mainboard and USB board connectors (Figure 1-26).
  • Page 22 8. Release the USB board (F) from the USB port slot and guide pin (G) on the top assembly. Then remove the USB board (Figure 1-27). WEEE Annex VII Component: USB Board Figure 1-27. USB Board Removal 1-20 Disassembly Procedures...
  • Page 23 Mainboard Removal Prerequisite: Ensure that the Heatsink and Fan have been disassembled prior removing the mainboard. 1. Remove three (3) screws (A) securing the right side of LCD hinge in place (Figure 1-28). Figure 1-28. Mainboard Removal 2. Lift the top assembly until it is fully open (Figure 1-29).
  • Page 24 3. Close the top assembly and lift the right side of LCD hinge until it is fully extended (Figure 1-30). Figure 1-30. Mainboard Removal 4. Gently peel off the mylar (B) from the mainboard. While detaching the mylar, be careful to release it from the guide pins (C) (Figure 1-31).
  • Page 25 10. Disconnect the speaker cable from the mainboard connector (I) (Figure 1-32). 11. Disconnect the eDP cable from the mainboard connector (J) (Figure 1-32). CAUTION: Make sure all cables, FFCs, and FPC are disconnected from the connectors on the mainboard to avoid damage during removal. 12.
  • Page 26 Figure 1-34. Mainboard IMPORTANT: Circuit boards >10 cm² have been highlighted with a yellow rectangle as shown in Figure 1-34. Remove the circuit board and follow local regulations for disposal. 1-24 Disassembly Procedures...
  • Page 27 LCD Panel Removal Prerequisite: LCD Module Removal 1. Pry the LCD panel from the left side to release latches (Figure 1-35). Figure 1-35. LCD Panel Removal 2. Continue along the upper side of the LCD panel (Figure 1-36). Figure 1-36. LCD Panel Removal Disassembly Procedures 1-25...
  • Page 28 3. Continue along the right side of the LCD panel (Figure 1-37). Figure 1-37. LCD Panel Removal 4. Carefully lift the LCD panel (A) (Figure 1-38). CAUTION: Do not remove the LCD panel yet because the eDP cable has not been released from the LCD hinges.
  • Page 29 5. Release the eDP cable from the rubber (B) inside the left LCD hinge cap (Figure 1-39). Figure 1-39. LCD Panel Removal 6. Remove the LCD panel. Disassembly Procedures 1-27...
  • Page 30 Top Assembly Removal (Keyboard Removal) Prerequisite: Ensure that the LCD Module, WLAN Antenna, Fingerprint Module, USB Board, and Mainboard have been disassembled prior removing the top assembly. NOTE: NOTE: The keyboard is included as part of the top assembly and cannot be disassembled. In the event that the keyboard can no longer be used, replace the entire top assembly.
  • Page 31 Troubleshooting This chapter shows you how to deal with common system problems. Read it before calling a technician if a problem occurs. Solutions to more serious problems require opening up the computer. Do not attempt to open the computer yourself; contact your dealer or authorized service center for assistance.
  • Page 32 FRU (Field Replaceable Unit) List Please contact your local service center to find out how to obtain the part or replace your device. 1-30 FRU (Field Replaceable Unit) List...
  • Page 33 Exploded Diagrams Figure 1-41. System Exploded Diagram Exploded Diagrams 1-31...
  • Page 34 Table 1-2. System Exploded Diagram Description Top Assembly Conductive Tape Mylar (for mainboard) Insulator Mylar Acetate Tape Speakers USB Board FFC (low speed) USB Board FFC (high speed) USB Board Mainboard Touchpad FFC Touchpad Module WLAN Antenna (MAIN+AUX) Battery Pack SSD Module Base Cover 1-32...
  • Page 35 Figure 1-42. LCD Assembly Exploded Diagram Table 1-3. LCD Assembly Exploded Diagram Description LCD Module Camera Module G-sensor Cable G-sensor Board LCD Hinge L LCD Hinge R eDP Cable LCD Cover Exploded Diagrams 1-33...
  • Page 36 Software Update Updating your software Please visit http://go.acer.com/?id=17883 1-34 Software Update...
  • Page 37 Personal Data Removal Removing your personal data There are three options to choose from: Option 1: Select Start > Settings > Update & Security > Recovery. Under  Reset this PC, select Get started. Open Recovery settings. Option 2: Restart your PC to get to the sign-in screen, then press and hold down ...

Table of Contents