Page 2
Smart Heavy-Duty Vehicle TPMS Solution Introduction The Smart Heavy-Duty Vehicle TPMS Solution is designed to report you the information of tires on your vehicle. The complete solution includes a Smart Main Unit, TPMS Sensors, a Repeater and a Trailer Receiver. The Smart Main Unit can automatically search and match the TPMS Sensors, save your time from repeated and complicated adjustment.
Smart Heavy-Duty Vehicle TPMS Solution Packing List Item Name 18-Wheel Solution 6-Wheel Solution EV-LM06 (Main Unit) ACC to mini USB cable Hook and loop tape Cable tie EV-TR01 (Trailer Receiver) EV-RP01 (Repeater) EV-S01 (Sensor) x 18 EV-S01 Battery x 18...
Note: 1. Equipment configurations and supplied accessories vary by country. Please consult your local EverFocus office or agents for more information. Please also keep the shipping carton for possible future use. 2. Contact the shipper if any items appear to have been damaged in the shipping process.
Page 5
Smart Heavy-Duty Vehicle TPMS Solution EMV1200/800/400 HD Mobile DVR • Full HD mobile DVR (supports Analog SD/HD cameras) • Up to 1080p resolution for recording • eZ.Controller function: Control camera OSD settings and PTZ operation directly from DVR end • Support HDD (up to 1TB) or SSD •...
Smart Heavy-Duty Vehicle TPMS Solution Installation Architecture 18-Wheel Solution 6-Wheel Solution 2.1 Main Unit Installation 1. Connect the main unit to ACC power using the supplied ACC to mini USB cable, red wire to ACC power and black wire to GND.
Smart Heavy-Duty Vehicle TPMS Solution 2. Use the supplied Hook and loop tape to fix the main unit. Hook and loop tape Hook and loop tape 2.2 Sensor Installation 1. Check the sensor number according to the sticker on the sensor. The number corresponds to the order of installing the sensor.
Page 8
Smart Heavy-Duty Vehicle TPMS Solution Sensor Installation order 11 12 15 16 17 18 2. Put the supplied EV-S01 Battery into the sensor, then tighten the cap until the water-proof ring is thoroughly covered. Water-proof Ring 3. Screw the sensors to the corresponding tires follow the installation order.
Page 9
Smart Heavy-Duty Vehicle TPMS Solution 4) Use the supplied EV-S01 Wrench to tighten the EV-S01 Lock Nut for securing the sensor. Wrench Lock Nut Note: 1. It is recommended to replace the sensor battery when the battery voltage is below 2.7V.
Page 10
Smart Heavy-Duty Vehicle TPMS Solution 2.3 Antenna Extension Cable Installation 1. Connect the antenna cable of the repeater or the trailer receiver with the supplied 10m antenna extension cable. 2. Wire the antenna extension cable along the vehicle’s body wiring to the chassis that near the rear wheels.
Smart Heavy-Duty Vehicle TPMS Solution 2.4 Repeater Installation The repeater repeats the signal from the sensors. It is recommended to install the repeater in the vehicle's rear area. 1. Connect the power cable to the 9 ~ 30V battery power, red wire to ACC power and black wire to GND.
Smart Heavy-Duty Vehicle TPMS Solution 3. Main Unit Operation 3.1 Buttons for Configuration Power Switch Pressure Unit Backlit Temperature Unit Symbol Button Function In Normal Mode: Power switch ON / OFF. Power Switch In Setting Mode: Select backlit color. In Normal Mode: Press for 5 seconds to enter the Pressure Unit pressure setting mode.
Smart Heavy-Duty Vehicle TPMS Solution 3.2 Normal Mode There are 4 operation modes of the main unit. In Normal mode, the information of each sensor will be displayed by turns. Wireless Sensor Sensor Signal Battery Receiving Strength Capacity Signal Current...
Smart Heavy-Duty Vehicle TPMS Solution Current Tire Displayed Display the current detected tire. When under-inflation, over-inflation Alarm or abnormal temperature of the tires is detected, the alarm icon will flash. 3.3 Alarm Mode When abnormal pressure or temperature of the tires is detected, the system enters Alarm mode.
Smart Heavy-Duty Vehicle TPMS Solution 3.4 Setting Mode In Setting mode, you can configure system settings include wheel number, temperature limit, pressure limit, backlit color, mute. Follow the steps below to enter each setting menu. 3.4.1 Wheel Number Setting In Normal mode, press Power Switch button...
Page 16
Smart Heavy-Duty Vehicle TPMS Solution Set up the temperature high limit for the front-left and front-right tires. Use Pressure Unit button and Temperature Unit button to increase or decrease temperature value. The default temperature high limit is 85°C. Press Backlit button to save.
Page 17
Smart Heavy-Duty Vehicle TPMS Solution 2. Set up the pressure high limit for the front-left and front-right tires. Use Pressure Unit button and Temperature Unit button to increase or decrease pressure value. The default pressure high limit is 132psi. Press Backlit button to save.
Smart Heavy-Duty Vehicle TPMS Solution 5. Continue to set up the pressure low limit for the other tires. Use Pressure Unit button and Temperature Unit button to increase or decrease temperature value. The default pressure high limit is 95.0psi. Press Backlit button to save and exit.
Page 19
Smart Heavy-Duty Vehicle TPMS Solution 4. The sensors detected will be displayed on the screen. If you have a total of 6 sensors, the system should detect at least 6 sensors. Sensor Detected Tire waited for pairing 5. Screw the sensors to the corresponding tires follow the installation order. (See 2.2 Sensor Installation) 3.5.2 Pair a Single Tire...
Page 20
Smart Heavy-Duty Vehicle TPMS Solution 4. Trailer Receiver Operation You can use the ID Learning function of the iTPMSystem to pair the sensor LEDs with sensors. iTPMSystem for Android devices: https://play.google.com/store/apps/details?id=Atbs.iTpms&hl=zh_TW iTPMSystem for iOS devices: https://itunes.apple.com/tw/app/tpms/id542118415?l=zh&mt=8 Please be noted that the trailer receiver only receive and transmit signal from sensor number 7 ~ 18, therefore the LED number 1 ~ 12 on the trailer receiver actually corresponds to the sensor number 7 ~18.
Page 21
Smart Heavy-Duty Vehicle TPMS Solution 1. Turn on the Bluetooth function on your mobile device and then search for the Trailer Receiver. 2. Run the iTPMSystem and then tap the ID Learning tab. 3. You can tap the Edit button to manually enter the sensor’s ID number for each wheel group,...
Smart Heavy-Duty Vehicle TPMS Solution 5. Troubleshooting Main unit does not receive any signal from sensor: 1. Remove the sensor from the tire, and see if the main unit receive the signal from the sensor. 2. If the main unit does not receive any signal, put the sensors near the main unit, remove the EV-S01 Battery from the sensor and then put it into the sensor again.
Page 23
Smart Heavy-Duty Vehicle TPMS Solution 1. Check the brake. When you hit the brakes too often or the brake does not work correctly, the tire temperature may increase. 2. Slow your driving speed, and arrange a vehicle maintenance as soon as possible.
Page 24
Smart Heavy-Duty Vehicle TPMS Solution Below information appears on the main unit: The system does not receive the tire pressure from the current tire. 1. Check the tire pressure of the current tire. 2. Make sure the valve thimble is installed properly.
Page 25
FAX: +81 3 5625 8189 sales@everfocus.com www.everfocus.co.jp info@everfocus.co.jp Ihr EverFocus Produkt wurde entwickelt Your EverFocus product is designed and und hergestellt mit qualitativ manufactured with high quality materials hochwertigen Materialien und and components which can be recycled Komponenten, die recycelt und wieder and reused.