Related Manuals for Bazooka RSA150.2HC
Summary of Contents for Bazooka RSA150.2HC
- Page 3 Dear customer, Congratulations on your purchase of a Bazooka RS high-performance amplifier. At Bazooka, we are fanatics about accurate music reproduction. Your selection of our products for your sound system indicates that quality sound is also important to you too. At SAS, we take great pride in manufacturing revolutionary audio products, and through the years of engineering expertise, hand craftsmanship and critical testing procedures, we have created the RS high-performance series of amplifiers.
- Page 4 Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the power amplifier not the car's battery! To ensure maximum power transfer and secure safe connections, it is recommended to use high grade barrier spades (for connection at amplifier) and terminal rings...
- Page 5 This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. The circuit protects the amplifier from damage due to a short found in the speakers or wiring.
- Page 6 For added low frequency performance the amplifiers are equipped with a variable 0~12 dB bass boost @ 45Hz. One set of full range line outputs have been provided for convenient connection to additional amplifiers in the system. This protects the amplifier against short circuits and excessive current. Automatically turns amplifier on when connected to the head unit's remote output.
- Page 7 Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the trunk or under the seat.
- Page 8 RADIO'S REMOTE RADIO'S REMOTE TURN-ON OUTPUT TURN-ON OUTPUT 94.7 94.7 IMPORTANT! Before making any connections, disconnect the car’s battery until the installation is completed to avoid possible damage to the electrical system. At times, the amplifier will need to draw large levels of current that cannot be At times, the amplifier will need to draw large levels of current that cannot be At times, the amplifier will need to draw large levels of current that cannot be provided by any circuit in the car's fuse box.
- Page 9 Please note that when making these connections the signal inputs correspond with the speaker outputs. Optional full range line out connection to additional amplifiers in the system. RSA75.2HC & RSA150.2HC SIGNAL CONNECTIONS Optional full range line out connection to additional amplifiers in the system. RSA800.1D SIGNAL CONNECTIONS...
- Page 10 When connecting, make sure that positive (+) from the amplifier is connected to the positive (+) of the speaker, and the same for negative (-). RSA75.2HC & RSA150.2HC SPEAKER CONNECTIONS RSA800.1D SPEAKER CONNECTIONS RSA75.2HC POWER...
- Page 11 The RS amplifiers are capable of being bridged in a mono configuration. This feature allows you the flexibility of using the amplifier to drive a ** subwoofer or a center channel. In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output.
- Page 12 The RSA75.2HC and RSA150.2HC are capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers.
- Page 13 Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. possibility of induced noise from the car's electrical system (i.e.
- Page 14 (Please note: If you intend to use the RSA75.2HC or RSA150.2HC in the Tri-mode configuration, it is necessary to set the crossover control to the “FLAT” setting in order to receive full range output) The “RS” amplifiers are equipped with a built-in crossover network allowing you to select the crossover type (i.e.
- Page 15 We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components in the system that could cause various signal problems such as inducted electrical noise and engine noise.
- Page 16 Max Power Output Power @ 14.4 VDC : 4 ohm 2 ohm 1 ohm Bridged 4 ohm Bridged 2 ohm Frequency Response + - 1dB S/N Ratio (A-weight) THD with 80k filter Low Input Level Battery Voltage Range Crossover Type Crossover Freq.
- Page 17 SAS’ option: SAS limits its obligation under any implied warranties under state laws to a period not to exceed the limited warranty period. SAS and its authorized BAZOOKA® dealers specifically disclaim liability for any incidental or consequential damages. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusions may not apply to you.
-
Page 18: How To Obtain Warranty Services
How to obtain warranty services: 1. You are responsible for delivery of the product to an authorized BAZOOKA® dealer or contact SAS at 1-800-THE TUBE for a Return Authorization number. The Return Authorization number must be clearly written on the outside of the box. Freight must be prepaid to SAS.