Page 4
Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent ven- dor.
Page 5
This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic information for servicing and/or upgrading components of the W210CUQ, W211CU, W215CU series notebook PC.
Page 6
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock and injury to per- sons when using any electrical equipment: 1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 7
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 8
Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag- netic fields. These can hinder proper performance and damage your data. Take care when using peripheral devices. Use only approved brands of Unplug the power cord before peripherals.
Page 9
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Preface Related Documents You may also need to consult the following manual for additional information: User’s Manual on DVD This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup pro- gram. It also describes the installation and operation of the utility programs provided with the notebook PC. FCC Statement This device complies with Part 15 of the FCC Rules.
Preface System Startup 1. Remove all packing materials. 2. Place the computer on a stable surface. 3. Insert the battery and make sure it is locked in position. 4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Preface Contents FCC Statement ................1-VIII Bottom ..................A-6 System Startup ................1-IX LCD (W210CUQ, W215CU) ............A-7 Introduction ..........1-1 LCD (W211CU) ................A-8 Schematic Diagrams......... B-1 Overview ..................1-1 Specifications ..................1-2 System Block Diagram ..............B-2 External Locator - Top View with LCD Panel Open ......1-4 Cedarview CPU Part D ..............B-3...
Page 14
Preface Click Board .................. B-28 Power Button Board ..............B-29 Power Button for M1115 .............. B-30 Updating the FLASH ROM BIOS..C-1 To update the FLASH ROM BIOS you must: C-1 Download the BIOS ............... C-1 Unzip the downloaded files to a bootable CD/DVD/ or USB Flash drive ....................
Chapter 1: Introduction Overview This manual covers the information you need to service or upgrade the W210CUQ, W211CU, W215CU series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about dri-vers (e.g. VGA & audio) is also found in the User’s Manual. The manual is shipped with the com- puter.
Display (particularly processor types/speeds) may be (Factory Option) External USB DVD Super Multi Drive changed, delayed or updated due to the manu- W210CUQ, W215CU: Module facturer's release schedule. Check with your 10.1” (25.65cm) WSVGA TFT LCD (Thickness: 5.2mm) service center for more details.
Page 17
10Mb/100Mb Ethernet LAN Dimensions & Weight 300K Pixel USB PC Camera Module (Factory Option) 1.3M Pixel USB PC Camera Module W210CUQ: (Factory Option) 3.75G/HSPA Mini-Card Module 266mm (w) x 185mm (d) x 19.7 - 27.1mm (h) 0.95kg (with 24.42WH Battery)
1. Built-In PC Camera 2. LCD 3. Power Button (Model C only) 4. Keyboard 5. Built-In Microphone 6. Touchpad & Buttons 7. LED Indicators W215CU W210CUQ, W211CU 1 - 4 External Locator - Top View with LCD Panel Open www.Teknisi-Indonesia.com...
Right (W215CU) 2. 2 * USB 2.0 Ports 3. RJ-45 LAN Port 4. External Monitor Port 5. Power Button (Models A & B only) Right ( W210CUQ, W211CU) External Locator - Front & Right Side Views 1 - 5 www.Teknisi-Indonesia.com...
Introduction External Locator - Left Side & Rear View Figure 4 Left Side View 1. Security Lock Slot 2. DC-In Jack 3. Vent LEFT SIDE VIEW 4. HDMI-Out Port 5. USB 2.0 Port 6. Microphone-In Jack 7. Headphone-Out Jack Figure 5 Rear View REAR VIEW 1.
Introduction External Locator - Bottom View Figure 6 Bottom View 1. Battery 2. Component Bay Cover 3. Vent 4. Speakers Overheating To prevent your com- puter from overhea- ting, make sure no- thing blocks any vent while the computer is in use.
Introduction Mainboard Overview - Bottom (Connectors) Figure 10 Mainboard Bottom Connectors 1. External Monitor Port 2. RJ-45 Lan Port 3. USB Ports 4. LCD Cable Connector 5. CPU Fan Cable Connector 6. Headphone-Out Jack 7. Microphone-In Jack 8. USB Port 9.
Chapter 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the W210CUQ, W211CU, W215CU series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated). We suggest you completely review any procedure before you take the computer apart.
Disassembly NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too). Maintenance Tools The following tools are recommended when working on the notebook PC: • M3 Philips-head screwdriver •...
Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re- moval and/or replacement job, take the following precautions: Power Safety Warning 1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other Before you undertake components could be damaged.
Disassembly Disassembly Steps The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: 1. Remove the battery page 2 - 5 To remove the System Memory: 1.
Disassembly Removing the Battery 1. Turn the computer off, and turn it over. Figure 1 2. Slide the latch in the direction of the arrow (Figure 1a Battery Removal 3. Slide the latch in the direction of the arrow, and hold it in place (Figure 1a 4.
Disassembly Removing the System Memory (RAM) Figure 2 RAM Module The computer has one memory socket for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting Removal DDR3 1066/1333MHz Memory (real operation frequency of memory depends on FSB of processor). The main memory can be expanded up to 2GB.
Page 33
Disassembly 4. Gently pull the two release latches ( & on the sides of the memory socket in the direction indicated by the Figure 3 arrows (Figure 3c). RAM Module Removal (cont’d.) c. Pull the release latches. d. Remove the module. 5.
Disassembly Removing the Wireless LAN Module Figure 4 Wireless LAN 1. Turn off the computer, remove the battery (page 2 - 5) and the component bay cover (page 2 - Module Removal 2. Carefully disconnect cables & , then remove screw from the module socket (Figure 4a 3.
Disassembly Removing the Keyboard Figure 5 Keyboard Removal 1. Turn off the computer and remove the battery (page 2 - 2. Use only the small tool provided (see picture below) to carefully press the four keyboard latches at the a. Press the four latches to top of the keyboard to elevate the keyboard from its normal position (Figure 5a).
Disassembly Removing the Hard Disk Drive Figure 6 HDD Assembly The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm Removal (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Page 37
Disassembly 3. Remove the HDD support module (Figure 7b Figure 7 4. Grip the mylar cover and slide the hard disk in the direction of arrow (Figure 7b HDD Assembly 5. Lift the hard disk out of the bay (Figure 7c Removal (cont’d.) 6.
Part Lists Appendix A:Part Lists This appendix breaks down the W210CUQ, W211CU, W215CU series notebook’s construction into a series of illustra- tions. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation.
Parts List Illustration Location The following table indicates where to find the appropriate parts list illustration. Table A - 1 Parts List Illustration Parts W210CUQ, W211CU, W215CU Location Top (W210CUQ) page A - 3 page A - 4 Top (W211CU)
Part Lists LCD (W211CU) Figure A - 4 LCD (W211CU) A - 8 LCD (W211CU) www.Teknisi-Indonesia.com...
Page 47
Part Lists LCD (W211CU) A - 9 www.Teknisi-Indonesia.com...
Page 48
Part Lists A - 10 LCD (W211CU) www.Teknisi-Indonesia.com...
Page 49
Schematic Diagrams Appendix B: Schematic Diagrams Table B - 1 SCHEMATIC This appendix has circuit diagrams of the W210CUQ, W211CU, W215CU notebook’s PCB’s. The following table indi- cates where to find the appropriate schematic diagram. DIAGRAMS Diagram - Page...
System Block Diagram 6-7P -W2105- 001 VDD3,VDD5 CLEVO Ce da r Rock -Ne tX Sys te m Bloc k Diagra m MB :6 - 71 -W 2 10 0 -D 0 1 DDR 3 On e C han nel 3.3V,5V,3VS,5VS,1.8VS IO : 6- 7 1- W2 1 01 - D0 1 14 .31 8 MHz...
Schematic Diagrams Cedarview CPU Part D U 12 D C EDARVIEW 1. 8V S 1. 8V S R E V = 1. 10 1. 05 V S R 29 R 3 7 L 26 B 18 H _S MI # H _S MI # *1K _0 4 R S V D _L 26...
Schematic Diagrams Cedarview CPU Part A-C-F D M I Sign al Gr ou p Z d iff = 80 Oh m ? 7.5% U 1 2 A C E D A R V IE W l en gt h =b r eak ou t( <=50 0mils) +(< = 6000 mils) C 2 3 7 0 .
Schematic Diagrams Cedarview CPU Part B M_A_DQ[ 63: 0] 6 U 12B U1 2F M_ A _A[1 5:0 ] CEDARVIEW AK 1 4 CED ARVIEW A 1 1 H 19 M_A_A0 M_A_DQ0 DDR 3_MA0 DD R3_DQ0 VS S VS S M_A_A1 AK 1 6 M_A_DQ1...
Schematic Diagrams Cedarview CPU Part E U12E C ED ARV IEW V CO RE 1.05V S _RS EN SE A A14 P 18 *H CB 1005K F-121T20_sho r t RE V = 1.10 1.05VS V CCA DDR _1 V CC _CP U_01 A A16 P 19 V CCA DDR _2...
Schematic Diagrams IDT CLOCK 1. 5 V S _C L K L 21 1. 5 V S *H C B 1 60 8K F -1 21 T2 5_ sh o r t 3 . 3 VS 3. 3 V S_ C L K L 20 *H C B 1 60 8K F -1 21 T2 5_ sh o rt 1 .
Schematic Diagrams Tigerpoint Part A-B USB Sig n al Gro u p Z d if f = 9 0 O hm ? 5% s ig n al / s p ac e : 5 / 6 m ils U13B U13A Tigerpoint Ti gerpoint DMI_ICH_MT_IR0_DN...
Schematic Diagrams Tigerpoint Part C SATA Signal Group Zdiff = 92 Ohm ? 0% signal / space : 4 / 5.5 mils U 1 3C R 12 AE 6 Tigerpoint AE 20 R SVD 0 3 SATA0R XN AD 6 SA TA RXN 0 12 R SVD 0 4 S ATA0R X P...
Schematic Diagrams Tigerpoint Part D 3. 3V U 1 3 D L PC Sign al Grou p A A 5 Tigerpo int T1 5 G P I O0 K B C _S MI # L D R Q 1# / G P I O2 3 B M_ B U S Y # / G P I O 0 W 1 6 K B C _ S W I #...
Schematic Diagrams Tigerpoint Part E-F 5V S 3. 3 V S 3. 3 V R 1 24 D 2 0 R 1 10 1 00 _1 %_ 04 R B 7 51 S-4 0C 2 1 0_ 1% _0 4 R B 7 51 S-4 0C 2 10mA C 1 38...
Schematic Diagrams Panel, HDD, LED PANEL P LV D D V I N 3 . 3V S R 50 R 5 2 D0 3 3. 3 V S _ LC D 3. 3 V S 0. 2 _0 6 0 . 2_ 0 6 BACKLIGHT ON CONTROL V OU T V I N...
Schematic Diagrams BTB, 3G, WLAN, BT MINI-PCIE CARD AND Debug Port 3G CARD 3 . 3V C 14 2 J _3 G1 40mils J _MI N I 1 0. 1 u_ 16V _ Y 5V _0 4 WA K E # 3.
Schematic Diagrams Audio Codec VT1812P CODEC (ALC269 & VT1802P) P V D D 1 _2 R 15 8 La yo ut n ot e: E M I Req uire * 15 mi l _ s ho rt _ 0 6 GND an d AUDG spa ce is 5 VS 60mils ~ 100 mi ls...
Schematic Diagrams KBC-ITE IT8502E-J, TP, LID TP CONN. K B C _A V D D L 31 MO DE L _ ID *H C B 10 05 K F-1 21 T 20 _1 0m i l _ sh ort V 1.0 W 210C U VD D 3 L4 2...
Schematic Diagrams USB PORT & USB CHARGER USB PORT_2 USB Charge PORT US B CHG V D D5 ? ? ? ? ? ? ? ? ? U S B_P N2 U SB _P N2_ R C 271 R127 * 0_04 U S B_P P 2 US B _P P2_ R 1 0u_10V _Y5V _08...
Schematic Diagrams PWR AC IN, CHARGE # ? Adapter ? ? 120W(? ),? ? ? ? ? ? ? ? 2PCS MOSFET,180 W~220W : 3 PCS , 300 W: 4PCS , 360W: 5PC S PR 90 V I N E MI 0 _0 4 P Q15 V I N...
Schematic Diagrams PWR 1.05VS 1.05VS 3.3V V DDQ PR69 P C56 1u_10V_Y5V_06 1.05VS 10K_04 V CNTL P J3 LDO_1.0 5V S 1.05VS _PWRGD VOU T PR68 1 00K _04 OP EN-2mm VOU T 1.05VS _EN P R66 1K_1% _04 P0515 7/ 9 P C54 82p_50V_NP O_04...
Schematic Diagrams PWR SW, 1.8VS, 3VS, 5VS, 1.5VS P2808 P Q 24 S Y S 15 V V D D 5 P 2 7 03 B A G 5 V S V I N E MI P C 77 0. 1 u_ 5 0V _ Y 5 V _0 6 V I N 1 P R 10 5 Pow er Pla ne...
Schematic Diagrams PWR VDD3, 3.3V, VDD5V, SYS15V V R E F P R 1 09 P C 71 P R 1 17 *0 _ 04 * 10 m i l _ sh o rt 1 u_ 1 0V _ Y 5 V _ 06 P R 11 9 12 0 K _1 % _0 4 P R 11 5...
Schematic Diagrams E _ J _C R T 1 1 08 A H 1 5 F S T0 4 A 4C 3 D A C _ R E D _ R E _D A C _ R E D D A C _ R E D _ R E _ L 5 *F C M1 00 5 MF -6 00 T 01 _ sh o rt E _ D A C _ R E D...
Schematic Diagrams Card Reader (w/ LAN) JMB261C C lo se to P IN 41 S D X C _P O WE R JMC261C E _R 22 0_0 4 S D _C LK Car d R ead er Pul l H igh /Lo w R esi sto rs S wi tc hin g Re gu la tor c lo se t o P IN 33 E _C 26 E _C 28...
Schematic Diagrams BTB, USB, CCD, PWR SW USB PORT_0&1 CONN. FOR CONT TO M/B E _ U S B VC C E _U S B VC C E _5V S E _3 . 3 VS E _R T C _B A T D 03 60mi ls E_ V D D 3...
Schematic Diagrams Click Board C_5V S C _J_T P 1 C _5VS C T PB UT T ON_R C T PB UT T ON_L C_J_TP1 LIFT K EY R IG H T KEY C_R 2 C_R 1 C _S W2 C _SW 1 10K _04 10K _04...
Schematic Diagrams Power Button for M1115 POWER SWITCH 6-53-3150B-245 6-53-3050B-241 SS_3.3 VS SS_3. 3VS SS_3.3 VS 6-53-3050B-240 POWER BUTTON SS_SW1 SS_J_SW 1 SS_R1 SF KQR MP2125 T SS_PD 1 SS_ BTN # 220_04 BAV99 85205- 03701 SS_GND Sheet 29 of 29 PN: 6- 20-51130-103 85205-03701 Power Button for...
Download the BIOS computer model. 1. Go to www.clevo.com.tw and point to E-Services and click E-Channel. Note that BIOS versions 2. Use your user ID and password to access the appropriate download area (BIOS), and download the latest BIOS files...
BIOS Update Use the flash tools to update the BIOS 1. Make sure you are not loading any memory management programs such as HIMEM by holding the F8 key as you see the message “Starting MS-DOS”. You will then be prompted to give “Y” or “N” responses to the programs being loaded by DOS.