Advertisement
Quick Links
RR2-M
INSTRUCTION MANUAL
INSTRUCTION MANUAL
RADIO RECEIVER – 2 CHANNELS
RADIO RECEIVER
EN
Electrical feeding 230V~ 433,92MHz
Electrical feeding 230V~ 433,92MHz
NEKOS S.r.l. - Via Capitoni, 7/5
Via Capitoni, 7/5 - 36064 Colceresa – VI –
+39 0424 411011 – +39 0424 411013 - www.nekos.it - info@nekos.it
+39 0424 411011
4420074 – Rev. 2003
CAUTION. Carefully observe all the following installation
instructions to ensure personal safety.
The device is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lacking experience and knowledge. Do not allow children to
play with the fixed controls and keep any remote-control units
out of their reach.
Have installation checks performed periodically by qualified
personnel from a service centre authorised by the manufacturer.
Do not use if repair or adjustment is required.
CAUTION. Disconnect the power supply during cleaning or
maintenance operations. Do not use solvents or jets of water to
wash the appliance; the appliance should not be submerged in
water.
In the event of fault or malfunction, switch off the device at the
main switch. All repairs and adjustments must only be
performed by qualified personnel from a service centre
authorised by the manufacturer.
Always request exclusive use of original spare parts. Failure to
respect this condition could compromise safety and invalidate
the benefits contained in the warranty for the appliance. In the
event of any problems or queries, consult your agent or contact
the manufacturer directly.
Carefully preserve these instructions after installation.
– ITALY
info@nekos.it
USER INSTRUCTIONS
The product must be disposed of in compliance with
local environmental regulations and not as household
waste.
2
Advertisement
Summary of Contents for nekos RR2-M
- Page 1 NEKOS S.r.l. - Via Capitoni, 7/5 Via Capitoni, 7/5 - 36064 Colceresa – VI – – ITALY +39 0424 411011 +39 0424 411011 – +39 0424 411013 - www.nekos.it - info@nekos.it info@nekos.it 4420074 – Rev. 2003...
- Page 2 Notes for functioning and use Notes for functioning and use RR2-M is a recessed radio receiver module, with 2 control relays, powered directly by the is a recessed radio receiver module, with 2 control relays, powered directly by the is a recessed radio receiver module, with 2 control relays, powered directly by the Safety indications ........
- Page 3 Electrical characteristics Electrical characteristics RR2-M is a small receiving module used for remote control of actuators, rolling shutters and blinds, wireless control for switching on lights, smart management. It has the following Tests were carried out at the ambient temperature of + 25 °C.
- Page 4 Device compliant with the European standards I-ETS 300 220 and ETS 300 683. PLATE AND MARKING DATA Led DL1 RR2-M receivers have marking and are destined for use in the European Union without Button further requirements.
- Page 5 A. General characteristics Function No. Effective Function Power supply: 110/230V~ /AC) 50/60 Hz Monostable Operating frequency: 433.92 MHz – NEKOS Protocol Bistable Modulation: ASK/OOK Timed “MOTOR CONTROL” MODE TX OPERATION 2 relay outputs: maximum current 5 Ampere. Examples: Pmax (230V) = 1250 VA for cosφ=1,...
- Page 6 The output can be controlled similarly locally as well. (E.g.: if the switch is closed, the output is activated for the set time, after which it is de- ERASING THE MEMORY OF THE RR2-M RECEIVER activated. If the switch is opened afterwards, the output is activated and the timer starts over.
- Page 7 If the cancellation was successful, the receiver will emit 5 x 5 + short blinks and 5 beeps. To erase an additional transmitter, repeat step 4. Press the key of the receiver at the third blink. To end the procedure, wait for the time-out of 10 seconds. If the erase was successful, the receiver will emit 3 short x 3 + blinks and 3 beeps.
- Page 8 Confirm the operating hours by holding the programming > 3s Hold the programming button of the MINI-RX pressed. > 3s button of the MINI-RX pressed for more than 3 seconds. The LED of the receiver blinks again and the buzzer emits The receiver will emit one (long) blink and beep of another beep.
- Page 9 Press briefly and release the programming button of the > 3s Hold the programming button of the MINI-RX pressed. The MINI-RX 2 times. LED of the receiver blinks again and the buzzer emits The LED of the receiver blinks twice and the buzzer emits another beep.
- Page 10 To disassemble the device and separate all materials for disposal, use a small screwdriver to remove the terminal board cover. declare that the document is issued under our sole responsibility and belongs to the following product: Apparatus model / Product: Radio receiver RR2-M Trademark: NEKOS Model/Type: RR2-M...