Jensen JPA1150M Installation & Operation Manual
Audiovox jensen jpa1150m: operation manual
Hide thumbs
Also See for Jensen JPA1150M:
- Quick start manual (3 pages) ,
- Installation & operation manual (19 pages)
Table of Contents
Advertisement
Quick Links
JPA1150M/JPA1300M
Amplifier Installation
& Operation Manual
JPA1150M/JPA1300M
Manual de Instalación y Operación
JPA1150M/JPA1300M
Manual de Installation et Operation
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicators and Controls . . . . . . . . . . . . . . . . . . 10
Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Remote Bass Control . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Contenido
Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Características . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Instalación. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Cableado . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Indicadores y Controles . . . . . . . . . . . . . . . . . .10
Pruebas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Control Remoto de Nivel . . . . . . . . . . . . . . . . . .13
Localización de Problemas . . . . . . . . . . . . . . . .14
Especificaciones . . . . . . . . . . . . . . . . . . . . . . . .15
Garantía. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Table des matières
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Dispositifs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Câblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Indicateurs et contrôles . . . . . . . . . . . . . . . . . . 10
Preuves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Commande à distance de niveau. . . . . . . . . . . 13
Localisations de problèmes . . . . . . . . . . . . . . . 14
Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Advertisement
Table of Contents
Related Manuals for Jensen Jensen JPA1150M
Summary of Contents for Jensen Jensen JPA1150M
-
Page 1: Table Of Contents
JPA1150M/JPA1300M Amplifier Installation & Operation Manual JPA1150M/JPA1300M Manual de Instalación y Operación JPA1150M/JPA1300M Manual de Installation et Operation Contents Introduction ......2 Features . -
Page 2: Introduction
Introduction We appreciate your recent purchase of a Jensen amplifier. It is your continued commitment to us that allows us to bring you new and innovative products year after year. The new Jensen JPA series of amplifiers has been redesigned for 2005 to meet or exceed the CEA-2006 test standards. -
Page 3: Features
JPA1150M/JPA1300M Features • Designed and engineered in the U.S.A. • Unregulated MOSFET Pulse Width Modulated (PWM) power supply for extended dynamic range with soft-start circuitry • Main B+ Input filtering (Pi type filter) • High current driver and output stage transistors •... -
Page 4: Installation
Installation Before you begin the installation of your POWER series amp remember, there are two ways to do things – right and twice! Use the proper installation techniques, tools and accessories to insure that your Jensen POWER series amp will put out all the power it was designed to. - Page 5 JPA1150M/JPA1300M Disconnect Battery Disconnect the negative (-) battery cable before starting the installation. Check the battery ground (there should be two (2) ground wires coming from the battery - one going to the starter mounting bolt or engine block and another going to the vehicle chassis) and make sure the battery is grounded to the chassis with at least a #8 gauge wire.
-
Page 6: Wiring
Wiring Charging System The installation of just one (1) JPA1150M/JPA1300M amplifier could be enough to overload your factory electrical system. You may need to upgrade your alternator and battery. Once the battery is used to start your vehicle, the alternator is responsible for keeping all the electrical devices in your vehicle supplied with the proper power, including your amplifiers. - Page 7 JPA1150M/JPA1300M Power Terminal (+12V) Connect the main power wire to the battery, within 18 inches from the positive (+) battery post, using an adequate size fuse or circuit breaker capable of handling the current of the selected power wire. A fuse or circuit breaker must be installed to prevent a possible electrical fire should the main power wire short to ground.
- Page 8 Wiring (continued) Speaker Wiring (SPEAKER) The Speaker Wiring diagrams illustrate options for connecting one or two subwoofers. In addition, when installing or connecting full-range speakers, you must observe the proper speaker polarity. NOTE: Do not overlook the use of the proper gauge speaker wire.
- Page 9 JPA1150M/JPA1300M Input Wiring Low Level RCA Input (INPUT) Low level (RCA) input is preferred for best performance. Most trunk/hatchback installations will require a 15-20 foot RCA cable, while pickup trucks and under-seat mounting will require a 6-12 foot RCA cable. Connect an RCA cable from your receiver to the RCA input on your amplifier.
-
Page 10: Indicators And Controls
Indicators and Controls Power Indicator ( The power indicator provides a visual indication that the amplifier is turned on. Input Level Control (LEVEL) The input level control matches the output of your radio to the input of the amplifier. After the installation is complete, make sure the input level control on the amplifier is turned down all the way (counter-clockwise or all the way to the left). - Page 11 JPA1150M/JPA1300M Low Pass Filter (LPF) The Low Pass Filter controls adjust the crossover point from 40Hz to 250Hz. Typical crossover is between 60Hz and 80Hz for ported and sealed enclosures. Bandpass boxes will typically use a higher crossover setting between 125Hz and 175Hz.
-
Page 12: Testing
Testing Before finishing the installation, perform the following tests to make sure the wiring is correct and everything is operating properly. Reconnect Battery When wiring is complete, reconnect the battery negative terminal. Test Power Wiring Turn on the receiver, but do not turn up the volume. The amplifier power light should come on. -
Page 13: Remote Bass Control
JPA1150M/JPA1300M Remote Bass Control Remote bass control allows the input level to be adjusted from an alternate location. It can be mounted under-dash or in-dash. When the amplifier is used to drive subwoofers and the low pass crossover is activated, the remote bass control can be used as a “remote bass level control”. -
Page 14: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action Amplifier does not No power to +12V Check fuse(s) turn on terminal No power to REM Check head unit fuse(s) and terminal wiring Blown main fuse at Replace fuse and identify battery cause of failure Blown fuse at amplifier Replace fuse and identify cause of failure... -
Page 15: Specifications
JPA1150M/JPA1300M Specifications CEA Power Ratings JPA1150M Power Output: 150 watts RMS X 1 channels into 4-ohms @ < 1% THD+N Frequency Response: 10Hz to 100Hz (-3dB) Signal to Noise Ratio: 100dBA below reference (Reference: 1 watt) Additional Power Output: 200 watts RMS X 1 channels into 2-ohms @ <... -
Page 16: Warranty
La presente Garantía le otorga derechos especiales y usted puede gozar de otros derechos que varían de un estado a otro. U.S.A : Audiovox Corporation, 150 Marcus Blvd., Hauppauge, NY 11788, 1- 800-323-4815 CANADA: Llamar a 1-800-323-4815 para la ubicación de la estación de garantía a su area. - Page 17 JPA1150M/JPA1300M Audio Precision Regulated 1% THD/Power vs. Frequency CEA Standard Test Sweep Trace Power output - Rated power @ 2-ohm load. All channels driven. 30kHz filter. Sweep Trace Power output - Rated power @ 4-ohm load. All channels driven. 30kHz filter. JPA1150M Color Line Style...
- Page 18 Audio Precision Regulated 1% THD/Power vs. Frequency CEA Standard Test Sweep Trace Color Line Style Thick Cyan Solid Power output - Rated power @ 2-ohm load. All channels driven. 30kHz filter. Sweep Trace Color Line Style Thick Cyan Solid Power output - Rated power @ 4-ohm load. All channels driven.
- Page 19 Audiovox Electronics Corporation 150 Marcus Boulevard Hauppauge, NY 11788 1-800-323-4815 www.jensen.com © 2005 Audiovox v. 020405...