Audio Technica UniPoint AT853RWx Product Information

Description
The AT853Rx is a wide-range miniature
condenser microphone with a cardioid (unidi-
rectional) polar pattern. It has been designed
for use in high-quality sound reinforcement,
professional recording, television and other
demanding sound pickup applications. The
AT853Rx is furnished with a vinyl-coated
steel hanger that allows it to be positioned
inconspicuously over a choir, orchestra, stage,
etc., for very low-profile situations.
Supplied as a cardioid, the AT853Rx easily
accepts interchangeable elements to permit
selection of angle of acceptance from 100° to
360°. The following optional elements are
available from an authorized Audio -Technica
dealer or the A-T service department:
AT853H-ELE hypercardioid, AT853O-ELE
omnidirectional, AT853SC-ELE subcardioid.
The AT853Rx features a 25' (7.6 m) perma-
nently-attached miniature cable. Its free end
connects to the provided AT8533x power
module via internal solderless screw terminals
for simple length adjustment in the field. It
can be powered from any external 9V to 52V
DC phantom power supply. A recessed
switch in the power module permits choice
of flat response, or a low-frequency roll-off to
help control undesired ambient noise.
The microphone element is enclosed in a
rugged housing with a low-reflectance black
finish. It is also available in white as the
AT853RWx, with a white-finished microphone
housing, windscreen, cable and steel hanger,
for applications where the microphone must
be hung against a light background.
Installation and Operation
The combination of small size and excellent
response makes the AT853Rx ideal for sus-
pension over choirs, instrumental groups or
theater stages. A uniform 120° angle of
acceptance provides well-balanced audio
pickup. The microphone should be located
forward of the front-most source, above the
rear-most source, and "aimed" between
them (Fig. 1). Increasing the height of the
mic above the sources will tend to equalize
sound levels between them, but may also
increase background/reverberant sound
pickup. Whenever possible, the distance
from the mic to the rear-most pickup should
be no more than twice the distance to
the front source, to maintain front-to-rear
balance (Fig. 1).
Width of pickup is approximately three times
the distance to the closest performer. If addi-
tional mics are needed for wide sources,
they should not be closer together laterally
than three times the distance to the front
source, to avoid phase cancellation (Fig. 2).
To orient in the proper direction, twist the
microphone housing slightly in its wire holder
(clockwise rotation moves the microphone to
the right; counterclockwise rotation moves it
to the left). The foam windscreen slips over
the head of the microphone, effectively
reducing noise from wind or ventilation air
currents.
AT853Rx
AT853RWx
REMOTE-
POWERED
MINIATURE
CARDIOID
CONDENSER
MICROPHONES
120
120
ANGLE OF
ACCEPTANCE
MIC A
DISTANCE "X"
Figure 1. Figure 2.
Vertical positioning. Horizontal spacing.
Output is low impedance balanced. The out-
put connector of the power module mates
with XLRF-type cable connectors. The bal-
anced signal appears across Pins 2 and 3,
while the ground (shield) connection is Pin 1.
Output is phased so that positive acoustic
pressure produces positive voltage at Pin 2,
in accordance with industry convention.
To shorten the cable, remove the three
screws from the base of the power module
and slide the outer case up the cable to
reveal the circuit board and screw terminals.
Loosen the three terminal screws and remove
the cable from the module. Next, slide the
case off the cable, cut the cable to the
desired length (allowing a few extra inches)
and slide the case back onto the cable. Tie a
single knot in the cable about two inches
from the cut end. Following Figure 3 on the
back of this page, cut the cable off 1" down
from the top of the knot and carefully remove
1 / " of the outer jacket. Strip the mic cable
2
wires and attach them to their respective
terminals (Fig. 4). Make certain that the ter-
minals are clamped on the conductors, not
on the insulation, and that there are no loose
strands of wire which might touch other
terminals. Replace the case, being certain
that it goes over the case grounding contact
and that the roll-off switch is accessible.
Finish by replacing the three base screws
and testing for proper operation.
While a modern condenser microphone is
not unduly sensitive to the environment,
temperature extremes can be harmful. Avoid
leaving the microphone in the open sun or in
areas where temperatures exceed 110° F
(43° C) for long periods of time. Extremely
high humidity should also be avoided.
Architects and Engineers Specifications
The microphone shall be a fixed-charge con-
denser with a cardioid polar pattern and a
frequency response of 30 Hz to 20,000 Hz. It
shall be capable of accepting optional inter-
changeable elements for additional polar
patterns. It shall operate from an external 9V
to 52V DC phantom power source. Nominal
open-circuit output voltage with the included
power module shall be 7.0 mV at 1 kHz,
1 Pascal. Output shall be low impedance
balanced (200 ohms).
The microphone shall have a permanently-
attached 25' (7.6 m) miniature cable with a
pigtail output. The pigtail output shall be con-
nected to a power module via internal solder-
less screw terminals. The power module
shall include a switch for low-frequency roll-off
and shall terminate in a 3-pin XLRM-type out-
put connector.
The microphone shall be mountable in an
included steel hanger that allows permanent
overhead installation for pickup of dialogue,
120
orchestras, choirs and other large groups.
MIC B
The microphone shall be 1.39" (35.2 mm)
3 TIMES
long with a head diameter of 0.47" (12.0 mm).
The microphone weight shall be 0.4 oz.
(10 grams) without cable. The microphone
case, cable and steel hanger shall be black
[white].
The Audio-Technica AT853Rx [AT853RWx] is
specified.
Frequency Response
50 100 200
LEGEND 12" or more on axis (flat)
Roll-off
10 dB
500
1k 2k 5k 10k 20k
Frequency in Hertz