Advertisement
Quick Links
AE6100
HYPERCARDIOID DYNAMIC MICROPHONE
• Great presence with excellent monitor cut
• Maximum feedback rejection
• Superior anti-shock engineering for low handling noise
• Tough, durable, resilient – built for the road
• Hypercardioid polar pattern reduces pickup of sounds from the
sides and rear, improving isolation of desired sound source
Output from the microphone's XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2
and 3; Pin 1 is ground (shield). Output phase is "Pin 2 hot" –
positive acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must
be wired consistently: Pin 1-to-Pin 1, etc. For a high-impedance
(Hi-Z) mic input, connect a Lo-Z balanced cable to a Hi-Z match-
ing transformer (A-T CP8201 or equal) at the equipment input.
When using the AE6100 in settings with a stage monitor speaker,
the speaker should be located 135° off axis (45° off the rear of
the microphone). This placement, in conjunction with the
microphone's uniform hypercardioid pickup pattern, will virtually
eliminate the possibility of undesired audio feedback.
The high sensitivity of the AE6100 assures useful output and an
excellent match to most input sources. In some cases, however,
an attenuator such as the Audio-Technica AT8202 may be
required between the microphone and preamplifier to avoid
overloading sensitive input stages.
Take care to keep foreign particles from entering the windscreen.
An accumulation of iron or steel filings on the diaphragm, and/or
foreign material in the windscreen's mesh surface, can degrade
performance.
AE6100 SPECIFICATIONS
†
ELEMENT
POLAR PATTERN
FREQUENCY RESPONSE
OPEN CIRCUIT SENSITIVITY
IMPEDANCE
WEIGHT (less accessories)
DIMENSIONS
OUTPUT CONNECTOR
ACCESSORIES FURNISHED
† In the interest of standards development, A.T .U.S. offers full details on its test
methods to other industry professionals on request.
*1 Pascal = 10 dynes /cm
2
= 10 microbars = 94 dB SPL
Specifications are subject to change without notice.
Polar Pattern
0
330
30
300
60
270
90
240
120
50
210
150
180
SCALE IS 5 DECIBELS PER DIVISION
LEGEND
LEGEND
200 Hz
1 kHz
5 kHz
8 kHz
One-Year Limited Warranty
Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date
of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and
workmanship. In event of such defect, product will be repaired promptly without charge or, at
our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or
an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase
date. Prior approval from A.T.U.S. is required for return. This warranty excludes defects
due to normal wear, abuse, shipping damage, or failure to use product in accordance with
instructions. This warranty is void in the event of unauthorized repair or modification, or
removal or defacing of the product labeling.
For return approval and shipping information, contact the Service Department,
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law, A.T.U.S. will have no liability for
any consequential, incidental, or special damages; any warranty of merchantability or
fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from
state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51452-EN
©2002 Audio-Technica U.S., Inc.
Dynamic
Hypercardioid
60-15,000 Hz
–55 dB (1.7 mV) re 1V at 1 Pa*
250 ohms
10.9 oz (310 g)
6.97" (177.0 mm) long, 1.89"
(48.0 mm) head diameter, 1.30"
to 0.87" (33.0 mm to 22.0 mm)
tapered body diameter
Integral 3-pin XLRM-type
AT8470 Quiet-Flex
stand
™
clamp for
5
/
"-27 threaded
8
stands;
5
/
"-27 to
3
/
"-16
8
8
threaded adapter;
soft protective pouch
Frequency Response
100
200
500
1k
2k
5k
10k
Frequency in Hertz
12" or more on axis
Printed in Japan
10 dB
20k
Advertisement
