ADTRAN NetVanta ActivReach Quick Start

NetVanta ActivReach Wall Plate Media Converter
S
PECIFICATIONS
Conversion 1-pair or 4-pair ActivReach Ethernet to standard
10/100Base-T
Compliance EN 60950-1, IEC 60950-1, AS/NZS 60950-1, UL/CUL 60950-1
FCC Part 15 Class B, EN 300 386, ICES 003 Class B
RoHS compliant
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This
device must accept any interference received, including
interference that may cause undesired operation.
Physical Dimensions: 3.50-inch W x 2.00-inch H x 1.12-inch D
Operating Temperature: 0°C to 40°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95 percent, noncondensing
• The NetVanta ActivReach Wall Plate Media
Converter is intended for intrabuilding use only.
• Ensure that the Wall Plate Media Converter wiring
is installed in accordance with all national, state,
and local electrical codes.
• The Wall Plate Media Converter is intended for use
only in low-voltage, communication-level junction
boxes only. It must not be used in a junction box
containing AC power.
• PoE cables are intended for intrabuilding use only.
Connecting an ADTRAN PoE unit directly to PoE
cables that run outside the building in which the unit
is housed will void the user's warranty and could
create a fire or shock hazard.
• Ethernet cables are intended for intrabuilding use
only. Connecting an ADTRAN unit directly to
Ethernet cables that run outside the building in
which the unit is housed will void the user's
warranty and could create a fire or shock hazard.
Quick Start Guide, 61702595F17-13A, March 2015
D
ESCRIPTION
The NetVanta ActivReach Wall Plate Media Converter is designed to be
mounted to data junction boxes in a building's existing infrastructure. It converts
ADTRAN's ActivReach Ethernet to standard 10/100Base-T over varying cable
types and cable distances well beyond the standard Ethernet limitation of
100 meters. The NetVanta ActivReach Wall Plate Media Converter has no input
power supply, rather it draws power from an upstream ActivReach Ethernet
Switch (NetVanta 1535P, P/N 1702595G10 or NetVanta 1235P,
P/N 1700595G10). The optional Access Point (AP) Mounting Kit for NetVanta
ActivReach Wall Plate Media Converter (P/N 1702595F21) can be used to easily
mount an AP directly to the Media Converter. Refer to the quick start guide that
ships with the AP mounting kit for mounting instructions.
The NetVanta ActivReach Wall Plate Media Converter can be used in the
following configurations: 1-pair ActivReach over legacy copper/Cat 3/5/6 cable
and 4-pair ActivReach over Cat 3/5/6 cable. There is also an optional voice
passthrough configuration that will allow a legacy POTS line to pass through the
unit. For a description of ActivReach pin connections, see the
Connections
Converter for each configuration, refer to the
ActivReach Ethernet on page
A
CTIV
Support - Phone: 888-423-8726, Email: support@adtran.com
illustrations below. For instructions on installing the Media
2.
• The NetVanta ActivReach Wall Plate Media Converter has
only one mode. It always provides PoE to the downstream
device. Caution must be taken when connecting the Wall
Plate Media Converter. It should not be used with a
downstream device that does not support PoE.
• The NetVanta ActivReach Wall Plate Media Converter
intended for use only with the NetVanta 1535P
(P/N 1702595G10) and the NetVanta 1235P
(P/N 1700595G10) ActivReach Ethernet Switches.
R P C
EACH IN ONNECTIONS
RJ-45
C
D A
B
8 7 6 5 4 3 2 1
1-pair ActivReach
connect pair A only.
4-pair ActivReach
connect pairs A, B, C, D.
Copyright © 2015 ADTRAN, Inc. All Rights Reserved.
P/N 1702595F17
ActivReach Pin
Installation Instructions for
RJ-11
POTS
6 5 4 3 2 1
Optional Voice Passthrough
connect pins 3 and 4.