Summary of Contents for Henny Penny OFE-141
- Page 1 Henny Penny Open Fryer Technical Manual Model OFE-141 Model OFE-142 FM06-052F 10-15-20...
- Page 2 This manual and Wiring diagram should be retained in a convenient location for future reference. The Model OFE-14X open fryer cannot be operated without electric power. The unit will automatically return to normal operation when power is restored. Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Section Page Section 1. INTRODUCTION 1-1. Introduction ......................1 1-2. Features ......................1 1-3. Proper Care ......................1 1-4. Assistance ......................1 1-5. Safety ......................... 1 Section 2. INSTALLATION 2-1. Introduction ......................3 2-2. Unpacking......................3 2-3. Leveling the Open Fryer ..................3 2-4. -
Page 5: Section 1. Introduction
SECTION 1. INTRODUCTION 1-1. INTRODUCTION The Henny Penny Open Fryer is a basic unit of food equipment designed to cook foods better and easier. This unit is used only in institutional and commercial foodservice operations. 1-2. FEATURES • Easily cleaned •... - Page 6 (continued) 1-5. SAFETY SAFETY ALERT SYMBOL is used with DANGER, WARNING or CAUTION which indicates a personal injury type hazard. NOTICE is used to highlight especially important information CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
-
Page 7: Section 2. Installation
2-2. UNPACKING The Henny Penny Open Fryer has been tested, inspected, and expertly packed to ensure arrival at its destination in the best possible condition. The unit is banded to a wooden skid and then packed inside a heavy cardboard carton with sufficient padding to withstand normal shipping treatment. - Page 8 Refer to the table below for supply wiring and fusing. VOLT （V） WATTS （KW） AMP（A） 21.2 19.45 To avoid electrical shock, this fryer must be adequately and safely grounded (earthed). Refer to local electrical codes for correct grounding (earthing) procedures or in absence of local codes, with The National Electrical Code, ANSI/NFPA No.
-
Page 9: Section 3. Operation
SECTION 3. OPERATING 3-1-1. Operating Components- C1500 Controls Reference Figure 3-1. Fig. Item Description Function Digital Display Shows the shortening temperature, the timer countdown in the Cook Cycle, and the selections in the Program Mode; the temperature of the shortening can be shown by pressing once, or twice to view set-point temperature;... - Page 10 Figure 3-1...
- Page 11 OFE14X The Computron 1500 controls are available on both split C1500 OPERATIONS electronic controls frypot and full frypot fryers. The following is a brief description AND PROCEDURES of the operating procedures for fryers with these controls. Be sure the drain valve is in the closed position. Place basket support inside of frypot.
- Page 12 OFE14X Before loading product into the baskets, lower baskets into the hot shortening to keep the product from sticking to the baskets. Once the shortening temperature has stabilized at the set-point temperature, lower the basket with product into the frypot. Do not overload, or place product with extreme moisture content into the basket.
- Page 13 OFE14X If “LOCK” shows in display when changing set-points or times C1500 PROGRAMMNG see Special Programming for unlocking INSTRUCTIONS To Change Set-Point Temperatures Press and hold until “PROG MODE” shows in the display. Press the desired product button. The LED above the button is on, “TEMP”...
- Page 14 OFE14X Special Programming is used to set the items below: C1500 SPECIAL Fahrenheit or Celsius PROGRAMMING Initialize System Lock or Unlock Controls Fryer Type – Open or Pressure Heat Source – Electric; Gas w/standing pilot; Gas w/electronic ignition;...
-
Page 15: Filling Or Adding Shortening
OFE14X 3-2. FILLING OR ADDING SHORTENING The shortening level must always be above the heating elements when the fryer is heating and at the frypot level indicators on the rear of the frypot. Failure to follow these instructions could result in a fire and/or damage to the fryer. -
Page 16: Filtering Of Shortening (Optional Feature)
OFE14X WITH PROLONGED USE, THE FLASHPOINT OF SHORTENING IS REDUCED. DISCARD SHORTEN- ING IF IT SHOWS SIGNS OF EXCESSIVE SMOKING OR FOAMING. SERIOUS BURNS, PERSONAL INJURY, FIRE, AND/OR PROPERTY DAMAGE COULD RESULT. 3-4. FILTERING OF Turn the main switch to the OFF position. Remove and SHORTENING clean the fry basket in soap and water. -
Page 17: Filter Pump Problem Prevention (Optional Feature)
OFE14X 3-4. FILTERING OF SHORTENING IF THERE ARE AIR BUBBLES COMING UP (Optional Feature) IN THE SHORTENING BEFORE ALL SHORTENING IS PUMPED UP, IT’S POSSIBLE (Continued) THAT THE FILTER CONNECTION AT THE UNION ON THE FILTER TUBE IS NOT TIGHTENED PROPERLY. IF SO, TURN OFF THE PUMP AND WEAR PROTECTIVE GLOVES OR CLOTH WHEN TIGHTENING THE UNION. -
Page 18: Filter Pump Motor Protector - Manual Reset (Optional Feature)
OFE14X 3-6. FILTER PUMP MOTOR In the event it overheats, the filter pump motor is equipped with a PROTECTOR – MANUAL RESET (Optional Feature) manual reset button located on the rear of the motor. After waiting 5 minutes to allow the motor to cool, press the reset button. -
Page 19: Cleaning The Frypot
OFE14X 3-8. CLEANING THE FRYPOT After the initial installation of the open fryer, as well as before every change of shortening, the frypot should be thoroughly cleaned as follows: 1. Turn the main POWER switch off The filter drain pan must be as far back under fryer as it will go. - Page 20 OFE14X 3-8. CLEANING THE FRYPOT (Continued) If the cleaning solution in the frypot starts to foam and boil over, immediately turn the power switch to OFF or damage to components could result. Do not use steel wool, other abrasive cleaners or cleaners/ sanitizers containing chlorine, bromine, iodine or ammonia chemicals, as these will deteriorate the stainless steel material and shorten the life of the unit.
-
Page 21: Regular Maintenance
OFE14X 3-9. REGULAR MAINTENANCE As in all food service equipment, the Henny Penny Open Fryer does require care and proper maintenance. The table below provides a summary of scheduled maintenance procedures to be performed by the operator. Procedure Frequency Filtering of shortening... -
Page 22: Wiring Diagram
OFE14X 3-10. OFE14X Wiring Diagram OFE141 split vat wire diagram... - Page 23 OFE14X OFE14X Wiring Diagram (Continued) 3-10. OFE141 full vat wire diagram...
- Page 24 OFE14X OFE14X Wiring Diagram (Continued) 3-10. OFE142 Split Vat Wire Diagram (一)
- Page 25 OFE14X OFE14X Wiring Diagram (Continued) 3-10. OFE142 Split Vat Wire Diagram (二)
- Page 26 OFE14X OFE14X Wiring Diagram (Continued) 3-10. OFE142 Full Vat Wire Diagram (一)
- Page 27 OFE14X OFE14X Wiring Diagram (Continued) 3-10. OFE142 Full Vat Wire Diagram (二)
-
Page 28: Section 4. Troubleshooting
OFE14X SECTION 4. TROUBLESHOOTING 4-1. TROUBLESHOOTING GUIDE Problem Cause Correction POWER switch ON but fryer • Open circuit • Plug fryer in completely inoperative • Check breaker or fuse at supply box Shortening will not • Open high limit • Reset high limit per heat but lights are on •... -
Page 29: Error Codes
OFE14X 4-2. ERROR CODES In the event of a control system failure, the digital display shows an error message. The message codes are shown in the DISPLAY column below. A constant tone is heard when an error code is displayed, and to silence this tone, press any button. DISPLAY CAUSE PANEL BOARD CORRECTION...