Related Manuals for SMA STORAGE-67-TS-10
Summary of Contents for SMA STORAGE-67-TS-10
- Page 1 Installation and Operating Instructions STORAGE-67-TS-10 ENGLISH STORAGE-67-TS-10 | Version 1.1...
- Page 2 Legal Provisions The information provided in this document is the property of SMA Solar Technology AG. No part of this docu- ment may be reproduced, stored in a retrieval system or transferred in any form or by any means (electronically, mechanically by photocopying or recording) without the prior written permission of SMA Solar Technology AG.
-
Page 3: Table Of Contents
8.1 Commissioning of a single unit ............. 30 8.2 Commissioning of STORAGE-67-TS-10 systems following the master/slave principle ....31 Shutdown . - Page 4 10.2 Capacity expansion using additional STORAGE-67-TS-10 units........
-
Page 5: Important Information About These Instructions
Do not open, perforate or drop the battery cells or modules. • Do not expose the battery cells or modules to high temperatures. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 6: General Safety Information
• the use of unauthorized spare parts. It is prohibited to carry out unauthorized reconstructions or technical modifications to the product. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 7: Intended Use
(STPS 60-10) manufactured by SMA. Any other use must be approved by the manufacturer and, if necessary, the local utility company. The unit may be operated only in closed rooms. The STORAGE-67-TS-10 works in an ambient air temperature range of -10 ° C to 50 ° C and at a maximum humidity of 85 %. -
Page 8: Safety
8 SAFETy 2 Safety The STORAGE-67-TS-10 meets the requirements of IEC 61508 parts 1 to 7 and complies with safety integrity level (SIL) 1. DANGER! Life-threatening electric shock from damaged components or short circuit Bridging the battery poles causes a short circuit resulting in a flow of electrical current. A short circuit of this type must be avoided under all circumstances. - Page 9 Do not use any battery inverters other than STPS 60-10. • Commission STORAGE-67-TS-10 battery storage systems within six months of delivery at the latest. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 10: Preparatory Work
Never move a cabinet once it has been fitted with battery modules, even using lifting gear. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 11: Transport At End Customer Site
The use of a hand truck is recommended. Caution: Do not damage the casing! The individual components of the STORAGE-67-TS-10 can weigh up to 120 kg and are therefore should not be transported by a single person. It is recommended that the system be installed by at least two people. The assis- tance of a hand truck is helpful. -
Page 12: Installation Location
When in doubt, consult a structural engineer. Dimensions All dimensions in cm. Space required (includ- Additional space required ing installation) for service etc. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 13: Technical Specifications
The STORAGE-67-TS-10 has been optimized for use with the 3-phase STPS 60-10 battery inverter. The overall system is perfectly matched to the needs of trade and industry. Thanks to the SMA Inverter Manager’s flexible energy management system and its high C-rate, STORAGE-67-TS-10 storage systems can be used for an extremely wide variety of applications. -
Page 14: Storage-67-Ts-10
11 . 5 11 . 3 14 BATTERIERAUM BATTERY ROOM Cabinet accessories DC connector set BatBreaker/ Installation guide USB drive Sticker for STPS battery chamber © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 15: Scope Of Delivery Storage-67-Ts-10
DC connector set BatBreaker for the Bat-INV (battery inverter) HV1000 2x 1000 mm, 35 mm Installation and Operating Manual STORAGE-67-TS-10 TESVOLT USB drive Battery chamber sticker © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 16: Connections And Layout Of The Sma Hv Apu
18 APU Fuse (F1) Fuse element to protect the SMA HV APU (2 A time-delay fuse (T) 5 x 20 mm, in accordance with DIN 41571- 2 type 521.020 from ESKA, 250 V ). System cannot be operated with a defective fuse. -
Page 17: Battery Module Wiring
BATTERy STORAGE SySTEM STORAGE-67-TS-10 17 5.5 Battery module wiring Wiring of 14 battery modules DC module connector rack balancing BAT COM sequence in the battery string © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... - Page 18 18 BATTERy STORAGE SySTEM STORAGE-67-TS-10 Wiring of 16 battery modules DC module connector rack balancing BAT COM sequence in the battery string © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 19: Installation
Place the cabinet in its final position pursuant to the specifications for the installation location in section “3.4 Installation location“ on page 12. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 20: Optional: Lifting The Top Of The Cabinet
Secure the cabinet covers using the M12 x 25 mm screws 11 . 1 plastic washers provided as well as the ones previously removed 11 . 2 in step © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 21: Installation Of The Components
7 .5 cabinet. NOTE Before installing the SMA HV APU, note its serial number. This is located on a sticker on the underside of the cabinet. Grounding the SMA HV APU is absolutely essential. Connect the... - Page 22 The plugs can be released by press- ing the push button on the side of the plug (see markings in the figure). © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 23 Connect the last module and the SMA HV APU using the connecting cable . Be certain to follow the instructions in section “5.5 Battery 4 .2 module wiring“ on page 17. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 24 Incorrectly connecting the BAT COM communication cable will cause the battery to malfunction. Ensure that connection is carried out properly in accordance with section “5.5 Battery module wiring“ on page 17 et seq. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 25 7 .2 is for connection to the negative pole. The plugs must audibly click into place. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 26 SMA Inverter Manager. Send the completed commissioning protocol to the SMA Service center. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 27: E-Stop Contact
The e-stop is used to quickly shut down the system. Since the battery storage system is not switched off properly when the e-stop is used, damage may be caused to components of the STORAGE-67-TS-10. you must therefore never use the e-stop to switch off the unit under normal circumstances. -
Page 28: Connection To The Sunny Tripower Storage 60
Always follow the specifications for connecting the STORAGE-67-TS-10 and the STPS 60-10. For example, no additional consumers or components may be included in the DC intermediate circuit between the battery and inverter. you must always consult the SMA Service center about any changes you would like to make to the sys- tem setup. -
Page 29: Diagram Of Connections Stps 60-10
25 –33 mm the connection. F Ethernet interface 2x Communication interface to the SMA Inverter Manager © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 30: Commissioning
The STPS 60-10 has been installed in accordance with the installation and connection specifications. Procedure Check the cabling of the STPS 60-10 and the STORAGE-67-TS-10 (also see the STPS 60-10 installation guide). Check the cabling of the components in accordance with section ““5.5 Battery module wiring“ on page 17 et seq. -
Page 31: Commissioning Of Storage-67-Ts-10 Systems Following The Master/Slave Principle
The STPS 60-10 has been installed in accordance with the installation and connection specifications. Procedure Check the cabling of the STPS 60-10 and the STORAGE-67-TS-10 (see the STPS 60-10 installation guide). Check the cabling of the components in accordance with section “5.5 Battery module wiring“ on page 17 et seq. - Page 32 When all slave storage systems have been commissioned, the master cabinet can be started up. To do this, switch the on-off “SWITCH” of the SMA HV APU to on. 17 © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 33 The status “Ok” will be shown on the display of the SMA HV APU. Now all STORAGE-67-TS-10s are now ready for oper- ation. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 34: Shutdown
Press the “Plant Stop” button at the top right of the LCS tool. The Inverter Manager will then lower the power out- put of the STPS to 0 kW, open the AC contactor of the STPS and give the command to the SMA HV APU to dis- connect from the DC path. -
Page 35: Expansion Of The Storage System
. In the event of any discrepancies, please contact our service center. Adjust the voltage of the original battery modules of the STORAGE-67-TS-10 so that it matches the voltage of the new battery modules exactly. Use the LCS tool. Further information on the procedure can be found in the follow- ing section “Adjusting the battery voltage via the LCS tool“... -
Page 36: Capacity Expansion Using Additional Storage-67-Ts-10 Units
Adjusting the battery voltage via the LCS tool NOTE For authoritative instructions on the LCS tool, please consult the applicable product documentation. Enter your SMA Grid Guard Code in the “Service” > “Grid Guard” tab. If you do not have the code, please contact our service center. - Page 37 > CAN OUT Master CAN IN > CAN OUT Slave 1 > SWITCH LAN 2 CAN OUT > CAN IN Slave 2 > optional LAN 1 © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 38 CAN IN > CAN OUT Slave 2 > SWITCH LAN2 CAN OUT > CAN IN Slave 2 CAN OUT > CAN IN Slave 3 > optional LAN1 © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 39 APU (Master 2) Reserve/optional last slave in the configuration STPS 60-10 (Master 3) Reserve APU (Master 3) Reserve LAN 2 switch (Master 4)/Service PC © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 40: Power Expansion Using Stps 60-10 Units
40 EXPANSION OF THE STORAGE SySTEM Overview of all addressing options BATTERY CHARGER ADDRESS Set the address selector on the SMA High-Voltage Active Power Unit (SMA HV APU) to match the configuration and information in the table below. LEFT SWITCH RIGHT SWITCH DESIGNATION... -
Page 41: Battery Monitoring Software - Batmon
The “System” menu item at the bottom of the BatMon interface includes a “Communication Port” button. Here, the serial number of the SMA HV APU must be selected under “Select APU” (this serial number can be found on a sticker on the underside of the SMA HV APU casing). - Page 42 42 BATTERy MONITORING SOFTWARE – BATMON Abbildung 11.2 “Battery” screen Abbildung 11.3 “Cells” screen © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 43: Menu Structure
This value indicates the percentage to which the battery has been charged. 100 % means that the battery is fully charged. The SMA HV APU can use the parameters to determine the state of charge of a cell or battery module, and to stop the charging process if necessary, thereby preventing overcharging. -
Page 44: Firmware Update
The latest firmware can then be downloaded with the “Firmware download” button on the “System” tab. In the window that opens, select the firmware file (.bin) and click “Open.” © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... - Page 45 FIRMWARE UPDATE 45 The update window will open. The update may take up to one minute. Afterwards, BatMon must be restarted. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
-
Page 46: Error And Warning Messages Storage-67-Ts-10
W947 Internal error Restart the battery. BMC internal in the controller NOTE For further assistance or if errors persist, contact the service center. © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 47: Maintenance
STOP STOP Before carrying out maintenance work, ensure that the STORAGE-67-TS-10 is taken out of operation in accor- dance with the instructions in section “9 Shutdown“ on page 34. NOTE: When cleaning and maintaining the STPS 60-10, always follow the specifications and instructions in the technical documentation for the STPS 60-10. -
Page 48: Disposal
3 . Batteries also contain important raw materials such as iron, zinc, manganese, copper, cobalt or nickel and can be recycled. Further information can be found at https://www.tesvolt.com/en/products/recycling.html Do not dispose of batteries in household waste! © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... -
Page 49: Contact
Κύπρος Αθήνα +33 472 22 97 00 +30 210 8184550 SMA Online Service Center : www.SMA-Service.com SMA Online Service Center: www.SMA-Service.com STP8-10-3AV-40-BE-de-10 Betriebsanleitung © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021... - Page 50 0699 SMA Online Service Center: www.SMA-Service.com Other coun- International SMA Service Line tries Niestetal 00800 SMA SERVICE (+800 762 7378423) SMA Online Service Center: www.SMA-Service.com Betriebsanleitung STP8-10-3AV-40-BE-de-10 © SMA Solar Technology AG Subject to changes to the technical content! Version 1.1 Last updated 04/2021...
- Page 52 www.SMA-Solar.com...