Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Ryobi RLT36X4BL
Summary of Contents for Ryobi RLT36X4BL
- Page 1 ORIGINAL INSTRUCTIONS Cordless Line Trimmer RLT36X4BL RLT36BL...
- Page 2 Important! It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modification.
-
Page 3: Intended Use
Safety, performance, and dependability have been given ■ Keep in mind that the operator or user is responsible top priority in the design of your cordless line trimmer. for accidents or hazards occurring to other people or their property. INTENDED USE PREPARATION The cordless line trimmer is intended to be used only by ■... -
Page 4: Transportation And Storage
■ Never use the product with damaged guards or without WARNING guards in place. Ensure that the line cut-off blade in the guard is properly ■ Do not fit a metal replacement line. positioned and secured before each use. ■ Keep hands and feet away from the cutting means at all times, especially when turning on the motor. -
Page 5: Residual Risks
Holding pin × 1 at frequent intervals for proper tightness to ensure that ■ Charger (RLT36X4BL only) × 1 the product is in safe working condition. Any part that is damaged should be properly repaired or replaced by an ■... -
Page 6: Symbols In This Manual
Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Bump feed head The following signal words and meanings are intended to explain the levels of risk associated with the product: Indicates an imminently hazardous situation, which, if not avoided, will... - Page 7 WHAT’S IN THE BOX RLT36X4BL...
- Page 8 WHAT’S IN THE BOX RLT36BL * Battery and charger are sold separately.
-
Page 9: Know Your Product
Know your product KNOW YOUR PRODUCT 1. Rear handle 6. Charger 11. Inner spool 2. Lock-out trigger 7. Lower shaft 12. Cutting line 3. Variable speed trigger 8. Line cut-off blade 13. Front handle 4. Battery latch button 9. Lower housing 14. -
Page 10: Getting Started
GETTING STARTED Always wear safety goggles or safety glasses with side shields Install the front handle to the upper shaft. Tighten the knob to when operating the product. Wear non-slip, heavy-duty protective secure. gloves. Wear non-skid, protective footwear that will protect your feet and improve your footing on slippery surfaces. - Page 11 GETTING STARTED Push the lock button, and remove the hanger cap from the lower Insert the lower shaft into the upper shaft until the lock button shaft. clicks into place. Tighten the knob to secure.
- Page 12 OVERVIEW Operating the product Adjusting the cutting width Replacing the line 406 mm p.11 p.14 p.15 355 mm Replacing the trimmer head Cleaning the product Storing the product p.17 p.18 p.19...
-
Page 13: Operation
OPERATION OPERATING THE PRODUCT WARNING: For safety reasons, the product must be adequately controlled by a two-handed operation. Hold the product with the right hand on the rear handle and the left hand on the front handle. WARNING: Beware of objects thrown by the cutting means. - Page 14 OPERATION NOTE: Use the speed selector to adjust the speed from high to low. 2. Push the lock-out trigger and squeeze the variable speed trigger to operate the product. 3. To advance the line, tap the knob on the ground until it reaches its full speed. The line advances each time the head is tapped.
- Page 15 OPERATION NOTE: The small blade fitted to the cutting attachment guard is designed to trim the new extended line to the correct length for safe and optimum performance. It is very sharp. Do not touch the blade, particularly when cleaning the product.
- Page 16 OPERATION 406 mm 355 mm ADJUSTING THE CUTTING WIDTH 1. Press the battery latch button, and remove the battery pack. 2. Loosen the screws on the line cut-off blades. Remove the blades. Rotate the line cut off blades 180º. NOTE: Runtime is increased on 33 cm setting. 3.
- Page 17 OPERATION REPLACING THE LINE 1. Press the battery latch button, and remove the battery pack. 2. Rotate the bump knob on the trimmer head until the line on the centre of the bump knob aligns with the arrows on the outer spool. 3.
- Page 18 OPERATION NOTE: Wind the line until approximately 12 cm remains protruding from the trimmer head. Wind the line at a slow, consistent pace. Winding the head too quickly causes inconsistency in 12cm 12 cm 12cm 12 cm spool tensioning, resulting in poor trimming performance.
- Page 19 OPERATION REPLACING THE TRIMMER HEAD 1. Press the battery latch button, and remove the battery pack. 2. Insert the holding pin into the slot underneath the trimmer head. Loosen and remove the trimmer head. 3. Install the new trimmer head. Tighten the trimmer head to secure.
- Page 20 MAINTENANCE CLEANING THE PRODUCT 1. Press the battery latch button, and remove the battery pack. 2. Clean the product with a soft, dry brush. WARNING: Keep the product away from corrosive agents, such as garden chemicals and de-icing salts. WARNING: The small blade fitted to the cutting attachment guard is designed to trim the new extended line to the correct length for safe and optimum performance.
- Page 21 STORAGE STORING THE PRODUCT NOTE: Clean the product before storing. 1. Press the battery latch button, and remove the battery pack. 2. Loosen the knob. Push the lock button on the lower shaft. Remove the lower shaft from the upper shaft. 3.
-
Page 22: Product Specifications
PRODUCT SPECIFICATIONS VIBRATION LEVEL Cordless Line Trimmer WARNING Model RLT36X4BL RLT36BL The declared vibration value has been measured with a Voltage 36 V 36 V standard test method and may be used to compare one tool with another. No-load speed... - Page 24 Imported by: Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149, Melbourne, Australia RYOBI is a trademark of Ryobi Limited, and is used Techtronic Industries N.Z. Limited under license. Unit C, 70 Business Parade South, © 2018–20 Techtronic Cordless GP.