Table of Contents
Advertisement
Installation Instructions
Delayed Egress
7100, 7200 Series Exit Device
WARNING
This product can expose you to
lead which is known to the state
of California to cause cancer and
birth defects or other reproductive
harm. For more information go to
www.P65warnings.ca.gov.
For technical support contact Yale
®
at 800.438.1951 x5033 or support@yalelocks.com
Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Available on the following devices:
*Rod Guards Required (made by other manufacturers
Attention Installer
Any retrofit or other field modification to a fire rated opening
can potentially impact the fire rating of the opening, and
Yale Locks & Hardware makes no representations or
warranties concerning what such impact may be in any
specific situation. When retrofitting any portion of an
existing fire rated opening, or specifying and installing a new
fire-rated opening, please consult with a code specialist or
local code official (Authority Having Jurisdiction) to ensure
compliance with all applicable codes and ratings.
Rim
Mortise
SquareBolt®
Concealed Vertical Rod
*Surface Vertical Rod
80-9470-0162-000 10/20
)
Advertisement
Table of Contents
Related Manuals for Yale Delayed Egress 7100 Series
Summary of Contents for Yale Delayed Egress 7100 Series
- Page 1 California to cause cancer and Yale Locks & Hardware makes no representations or birth defects or other reproductive warranties concerning what such impact may be in any harm.
-
Page 2: Table Of Contents
Wiring Diagram - Single Door Exit Only ........21 ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. - Page 3 Appendix: Legacy Boards ........... . .27 For technical support contact Yale ®...
-
Page 4: Panic And Fire Related Devices
NOTE: Components shown do not reflect all possible applications. Consult manufacturer for special applications. ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 5: End Cover And Pc Board Assembly
If key does not rotate freely, verify cylinder nut was placed in correct orientation. If arming switch does not trip, activator legs on arming switch activator can be bent to reduce or increase rotational travel. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com 80-9470-0162-000 10/20 Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 6: Dip Switch Settings
S2-8 ON or OFF. Ensure eight S2 Dip Switches are set per application before moving on to the next page of instructions. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 7: Installation Of End Cover Asssembly To Device
2-pin jumper to NC, then re-install PCBA/cover on rail. ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 8: Device Mounting
Wires must be protected from abrasion. • For use with Class II circuits only. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 9: Wiring Layout: Input/Output Wiring Descriptions
NOTE: Secure and Alarm Relay contacts are rated max load 1A @24VDC. ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 10: Electrolynx Connector System For All Electrical Installation
Feed harness through frame prep and mount electric hinge. B. If wiring later, plug pigtail harness connector into electric hinge connector. Feed harness through frame prep and mount electric hinge. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 11: Electrolynx Wiring Options Overview With Qc8 Hinge
Do NOT force connectors together any other way. ElectroLynx Wiring Options Overview with QC8 Hinge ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 12: Installing Delayed Egress Exit Device
See Section 14 for hole locations and sizes. Figure 6 ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 13: Electrolynx Wiring Options Overview With Qc12 Hinge
After routing two wires from ET through the chassis and the wire channel in back of rail then Install Molex Female 4-pin connector (supplied) onto pre-crimped female terminals ontoBlack wire pin 4-1, Red wire pin 4-2 For technical support contact Yale ®... - Page 14 ElectroLynx Wiring Options Overview with QC12 Hinge, continued Figure 7 ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc.
-
Page 15: Electrolynx Wiring Deed With "O" Trim Monitor Option And Qc12 Hinge
If external DPS wiring is NOT REQUIRED, set PCBA Dip Switch S2-7 ON. • If external DPS wiring is REQUIRED, set PCBA Dip Switch S2-7 OFF. Supplied with DEED when ordered with “O” Trim Monitor (Tmon) Option For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com 80-9470-0162-000 10/20 Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. - Page 16 Installation Instructions ElectroLynx Wiring Deed with “O” Trim Monitor Option and QC12 Hinge, continued Mechanical Trim For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc.
-
Page 17: Electrolynx Wiring Deed With Electrified Trim (Et) Option And Qc12 Hinge
Fail Safe 691F Electrified Trim (ET) Fail Secure ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20... -
Page 18: Electrolynx Wiring Deed With "S" Latchbolt Monitor Option And Qc12 Hinge
If external DPS wiring is NOT REQUIRED, set PCBA Dip Switch S2-7 ON. • If external DPS wiring is REQUIRED, set PCBA Dip Switch S2-7 OFF. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. - Page 19 ElectroLynx Wiring Deed with “S” Latchbolt Monitor Option and QC12 Hinge, continued Mechanical Trim ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc.
-
Page 20: Non-Electrolynx Door Prep
(32mm) Hinge Edge Of Door HINGE EDGE DETAIL For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20... -
Page 21: Wiring Diagram - Single Door Exit Only
BPS Power Supply or Local Building Ground Figure 10 ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20... -
Page 22: Wiring Diagram - "O" Trim Monitor Entry With External Door Position Switch
Electric trim operation will not affect armed device. Figure 12 ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 23: Wiring Diagram - 691F Electrical Trim Control
When an external DPS is used and door is opened and closed during momentary egress, the selected reset delay shall be canceled and the device shall re-arm. Device will now be back in delayed egress mode. For technical support contact Yale ® at 800.438.1951 x5033 or support@yalelocks.com 80-9470-0162-000 10/20 Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. -
Page 24: Additional Options Non Electrolynx Wiring
(refer to wiring diagrams for wiring). “S” Suffi x ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20... -
Page 25: Boca 15 Second Delay & Boca 30 Second Delay
30 seconds. The tone will then change to a continuous alarm until reset. Resetting of the alarm and re-arming of the device is accomplished by manual means only. For technical support contact Yale ®... -
Page 26: Troubleshooting
NOTE: If device is not working properly after troubleshooting, contact your local hardware distributor or local Yale representative, or contact Yale. Refer to the following table and notes for an explanation of each LED’s function. Diagonistic LEDs... -
Page 27: Appendix: Legacy Boards
Secure Rel ay Output (NO) To De vice; F actory Wired ® For technical support contact Yale at 800.438.1951 x5033 or support@yalelocks.com Copyright ©2018, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in 80-9470-0162-000 10/20 part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. - Page 28 ASSA ABLOY Americas International Tel: 1-905-821-7775 Yale Commercial is a business associated with ASSA ABLOY Access and Egress Fax: 1-905-821-1429 Hardware Group, Inc., an ASSA ABLOY Group company. Copyright © 2018, 2020, assaabloyai.com...