Parts List; Two Mounting Methods - Amana AMC4080AA Installation Instructions Manual

PARTS LIST

1. 3 Sets of bolts
2. 4-washers-A
3. 4-washers-B
4. 1-Template
Upon completing your check of the parts list, read all instructions completely before starting the installation. This will help you to become
familiar with the process and make installation easier.
(NOTE: It is suggested that you gather all needed tools and installation parts in one location.)
1
PREPARATIONS
Open the template and detach both segments along the dashed line with scissors. You should have two separate pieces.
• Template 1
• Template 2

TWO MOUNTING METHODS

There are two mounting methods described in this booklet that can be used.
1.
Countertop Method
You can use this method if you decide not to cabinet mount your oven.
To use your oven as a countertop model, simply position the oven on the desired counter and plug the electrical cord into a three
prong (grounded)wall receptacle.
2.
Cabinet Mounting Method
This method is for mounting your oven under a cabinet and uses the template, 4-washers and one set of screws. Before using this method,
the 4 plastic plug buttons on the top of the oven must be removed. This can be done by placing a thin flat blade screwdriver between the
plug button and the oven top and raising gently, taking care to avoid acratching the oven top.
OVEN MAY BE MOUNTED TO CABINETS WITH OR WITHOUT A FRONT RAIL.
2 3
15
25/64"
1 TEMPLATE
DETACH
TEMPLATE 1
TEMPLATE 2
IMPORTANT
Read the installation booklet for complete instructions before beginning installation.
Template must lay flat against the cabinet when locating the holes.
25/64"
15
INSTRUCTIONS
TEMPLATE
ON TOP SIDE
(A) CABINET
FRONT (See installation booklet for complete instructions.)
or If you drill the 4 mounting holes from the inside of the cabinet - place the
front edge of the template at the front edge of the cabinet.
Drill the 4 holes 1/4" DIA. as described in the installation instruction booklet.
CABINET
(B)
If you drill the mounting holes from the bottom side of the cabinet -
FRONT
measure the thickness of the front rail and cut that amount off the front of
TEMPLATE ON
the template. Use the cutting lines to insure a straight cut. Place the cut
BOTTOM SIDE
FRONT RAIL
edge against the back side of the front rail and position the template flat
THICKNESS
against the bottom side of the cabinet.
CUT EDGE
Drill the 4 holes 1/4" DIA. as described in the installation instruction booklet.
TEMPLATE
CUT LINES
FRONT
TEMPLATE 2
CABINET
(SIDE VIEW)
COUNTERTOP
4
DETACH
Read the installation booklet for complete instructions before beginning installation.
TEMPLATE
ON TOP SIDE
(A)
CABINET
FRONT
or If you drill the 4 mounting holes from the inside of the cabinet - place the
front edge of the template at the front edge of the cabinet.
Drill the 4 holes 1/4" DIA. as described in the installation instruction booklet.
(B) CABINET
FRONT If you drill the mounting holes from the bottom side of the cabinet -
measure the thickness of the front rail and cut that amount off the front of
TEMPLATE ON
BOTTOM SIDE the template. Use the cutting lines to insure a straight cut. Place the cut
FRONT RAIL
THICKNESS edge against the back side of the front rail and position the template flat
against the bottom side of the cabinet.
CUT EDGE
Drill the 4 holes 1/4" DIA. as described in the installation instruction booklet.
TEMPLATE
CUT LINES
FRONT
DETACH
CABINET FRONT
TEMPLATE
CUT LINES
1 1/4 INCH
1 INCH
1/2 INCH
1/4 INCH
FRONT
CABINET
(SIDE VIEW)
COUNTERTOP
15
25/64"
1 TEMPLATE
DETACH
TEMPLATE 2
IMPORTANT
Template must lay flat against the cabinet when locating the holes.
25/64"
15
INSTRUCTIONS
(See installation booklet for complete instructions.)
CABINET FRONT
TEMPLATE
CUT LINES
1 1/4 INCH
1 INCH
1/2 INCH
1/4 INCH
FRONT