Alvarion BreezeNET DS.11 Configuration Utility User Manual
Alvarion breezenet breezenet ds.11 wireless outdoor bridges: user guide
Hide thumbs
Also See for BreezeNET DS.11 Configuration Utility:
- Brochure & specs (2 pages) ,
- Release note (2 pages) ,
- User manual (97 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Alvarion BreezeNET DS.11 Configuration Utility
Summary of Contents for Alvarion BreezeNET DS.11 Configuration Utility
- Page 1 BreezeNET DS.11 Series Configuration Utility User's Guide September, 2000 Cat No. 213097 Rev A...
- Page 2 No other warranty is expressed or implied. The Company specifically disclaims the implied warranties of merchantability and fitness for any particular purpose. User’s Guide BreezeNET DS.11 Configuration Utility...
-
Page 3: Fcc Radiation Exposure Statement
FCC rules CFR47 part 15.204. The installer should configure the output power level of antennas, according to country regulations and per antenna type. BreezeNET DS.11 Configuration Utility 20cm (8 inches) 30cm (12 inches) Front Matter... - Page 4 Distance between devices. Configuration, statistic counters, and error messages as seen on the monitor. Description of problems encountered. To contact BreezeCOM Technical Support, refer to the Technical Support page of the BreezeCOM web site: www.breezecom.com User’s Guide BreezeNET DS.11 Configuration Utility...
-
Page 5: Table Of Contents
3.5 Station Control Tab... 17 3.6 Security Tab...18 3.7 Advanced Tab ...20 3.8 Counters Tab...21 3.8.1 Resetting Counters ...22 3.8.2 Link-Specific Counters ...23 3.9 Trap Monitor Tab ...23 3.10 Debug Info ...24 BreezeNET DS.11 Configuration Utility Table of Contents User's Guide... - Page 6 Figure 12. The Station Control Tab...17 Figure 13. Security Tab ...18 Figure 14. Advanced Tab...20 Figure 15. Counters Tab (BU Units) ...21 Figure 16. Counters Tab (RB Units)...21 Figure 17. Trap Monitor Tab ...23 User's Guide BreezeNET DS.11 Configuration Utility...
-
Page 7: General
Antenna selection and diversity setting Configuration of a wide range of operational parameters, including WLAN, IP and Security parameters View Tx and Rx counters Obtain general information such as the Firmware version and system name BreezeNET DS.11 Configuration Utility General User’s Guide... -
Page 8: Ds.11 Configuration Utility Main Window
The different tabs are described in the following sections. When you switch between the tabs, the IP Selection section with the selected unit address remains displayed. User's Guide BreezeNET DS.11 Configuration Utility... -
Page 9: Selecting Units
Click on an address to select the corresponding unit for viewing and configuration. For stations, which are located behind a router, type the unit's address in the Locate Unit field and click BreezeNET DS.11 Configuration Utility DS.11 Configuration Utility Main Window Control window containing the IP address,... -
Page 10: Setting The Snmp Community Information
Configuration utility should be on the same IP subnet as the assigned IP address. User's Guide for read and public private button. The Set IP dialog box is displayed. Figure 2. The Set IP Dialog Box BreezeNET DS.11 Configuration Utility for read/write) and click the... -
Page 11: Application Control Buttons
Firmware Upgrade - allows upgrading the embedded software in managed units; refer to Section 2.6 for instructions on using this feature. BreezeNET DS.11 Configuration Utility DS.11 Configuration Utility Main Window – Implements any changes you made. -
Page 12: Firmware Upgrade
1. Select the units which you wish to upgrade from the list box. Use Shift-click and/or Ctrl-click to select multiple units, or select multiple units by dragging with the mouse. User's Guide Figure 3. Firmware Upgrade BreezeNET DS.11 Configuration Utility... -
Page 13: Figure 4. Advanced Tftp Setup
If BU-DS.11 and RB-DS.11 devices are selected, the program upgrades RB-DS.11 units first. BreezeNET DS.11 Configuration Utility DS.11 Configuration Utility Main Window to change the settings of the TFTP session used in the upgrade Figure 4. -
Page 14: Figure 5. Firmware Upgrade Process
DS.11 Configuration Utility Main Window At the end of the upgrade session, the following window is displayed indicating that the operation was successful. User's Guide Figure 5. Firmware Upgrade Process BreezeNET DS.11 Configuration Utility... -
Page 15: Multiple Unit Configuration
Check the A log of the multiple configuration session is displayed during and after the operation. BreezeNET DS.11 Configuration Utility DS.11 Configuration Utility Main Window Figure 6. Multiple Configuration box to reset all affected units. -
Page 16: Utility Configuration Windows
MAC Address - MAC address of the selected unit. Firmware - The current firmware version. BSS Address (displayed for RB-DS.11 units only)- This defines the BSS address, which is the AP that the unit is associated with. User's Guide Figure 7. Station Status Tab BreezeNET DS.11 Configuration Utility... -
Page 17: Ip Parameters Tab
IP address was assigned. If an IP address was assigned manually, the system will not search for a DHCP server. Never - The system never searches for a DHCP server. BreezeNET DS.11 Configuration Utility Utility Configuration Windows Figure 8. IP Parameters Tab... -
Page 18: Snmp Parameters Tab
Address field and enter a new IP address. User's Guide Figure 9. SNMP Parameters Tab icon directly beneath this field to set the IP address of the PC icon directly beneath this field to clear the Trap Host IP BreezeNET DS.11 Configuration Utility... -
Page 19: Wlan Parameters Tab
The WLAN parameters tab allows you to define or edit parameters related to the Wireless LAN environment in which the selected unit is operating. The window displayed varies depending on the type of unit selected. BreezeNET DS.11 Configuration Utility Figure 10. WLAN Parameters Tab (BU Units) Utility Configuration Windows... -
Page 20: Figure 11. Wlan Parameters Tab (Rb Units)
No. 1, No. 2, or both (default: both antennas). Note: In the present product release, antenna diversity is not supported; therefore, always select Antenna No. 1. User's Guide Figure 11. WLAN Parameters Tab (RB Units) he unit adaptively selects the highest BreezeNET DS.11 Configuration Utility... - Page 21 If it does not find the BU-DS.11 on any of the preferred channels, it will continue to scan until it finds the BU-DS.11 on one of the 14 channels. BreezeNET DS.11 Configuration Utility User’s Guide...
- Page 22 Table 3-1. Frequency Selection List Channel Frequency Selection 2412 MHz 2417 MHz 2422 MHz 2427 MHz 2432 MHz 2437 MHz 2442 MHz 2447 MHz 2452 MHz 2457 MHz 2462 MHz 2467 MHz 2472 MHz 2484 MHz * Japan only BreezeNET DS.11 Configuration Utility...
-
Page 23: Station Control Tab
Export - Click the unit to a file. A popup window is displayed prompting you to specify the name of the file. BreezeNET DS.11 Configuration Utility Utility Configuration Windows Figure 12. The Station Control Tab button for all parameters to revert to defaults. -
Page 24: Security Tab
Wired Equivalent Privacy (WEP) is an authentication algorithm which protects authorized Wireless LAN users against eavesdropping, and is implemented in BreezeNET DS.11 units. The definition of WEP is defined in the IEEE 802.11 standard. DS.11 units can use one of the following authentication algorithms (as defined in the IEEE 802.11 standard). - Page 25 WEP Key row (First, Second, Third or Fourth) and entering 10 Hex digits (5 pairs of characters) for each of the 4 keys. After accepting the values, by clicking Apply, the WEP Key values are displayed as zeros for security reasons. BreezeNET DS.11 Configuration Utility User’s Guide...
-
Page 26: Advanced Tab
The default value is 4. Basic Rate - Enter the data rate at which broadcast, multicast and control packets are transmitted. The default value is 2 Mbps. User's Guide Figure 14. Advanced Tab BreezeNET DS.11 Configuration Utility... -
Page 27: Counters Tab
Utility Configuration Windows 3.8 Counters Tab Figure 15. Counters Tab (BU Units) Figure 16. Counters Tab (RB Units) Select a counter and drag it to the icon to view the graph. BreezeNET DS.11 Configuration Utility User’s Guide... -
Page 28: Resetting Counters
FCS Error - The number of CRC errors + percentage. 3.8.1 Resetting Counters You can reset the counters displayed in the Counters tab by clicking the button. All displayed values are reset to display zero. User's Guide BreezeNET DS.11 Configuration Utility... -
Page 29: Link-Specific Counters
Apply. When you click the the other counters which are only reset on screen). 3.9 Trap Monitor Tab BreezeNET DS.11 Configuration Utility Utility Configuration Windows button, these counters are actually reset (unlike Figure 17. Trap Monitor Tab... -
Page 30: Debug Info
To start recording, open the Debug Info option and select Start Log. When you finish recording (usually after 24 hours) select Stop Log and send the file to BreezeCOM technical support representatives. User's Guide button to clear the display area. BreezeNET DS.11 Configuration Utility...