Huawei Speed Wi-Fi NEXT W01 Notes Of Usage

・ As an instruction manual of this product, refer to the supplied "Quick start guide", "Notes on usage" (this guide), or "取扱説明書 詳細版 (Full
Instruction Manual)" (Japanese) available on the au homepage. In this manual, "Instruction Manual" includes "Quick Start Guide" (this manual), "Notes
on usage", and "取扱説明書 詳細版 (Full Instruction Manual)" (Japanese).
・ In this guide, "Speed Wi-Fi NEXT W01" is referred to as the "product".
・ All of the indicated amounts exclude tax unless otherwise specified.
Exemptions
• The Company is not liable for any damages arising from earthquakes, lighting, storms, floods or other natural disasters, as
well as fires, actions by third parties, other accidents, intentional or mistaken misoperation by the customer, or use under
other unusual conditions outside the responsibility of the Company.
• The Company is not liable for any incidental damages (change/disappearance of described content, loss of business
income, disruption of business, etc.) arising from use of or inability to use the product.
• The Company is not liable for any damages arising from failure to observe described content of the "Instruction Manual".
• The Company is not liable for any damages arising for example, from malfunction caused by combination with connected
devices or software not related to the Company.related to the Company.
• Settings etc. may sometimes be altered or lost due to faults, repair or other mishandling of the product. The Company is not
liable for any damage or lost due to faults, repair or other mishandling of the product.
• It is recommended you keep a copy of important data on your PC's hard disk Whatever the cause of the defect or
malfunction may be, the Company assumes no responsibility for alteration or loss of saved data.
• The product is used under WiMAX 2+ network environment; however, UQ Communications Inc. is not liable for quality of the
product etc.
* "The Company" as appears in this manual refers to the following companies:
Sold by: KDDI CORPORATION·OKINAWA CELLULAR TELEPHONE COMPANY
Imported by: HUAWEI Technologies Japan K.K.
Manufactured by: HUAWEI TECHNOLOGIES CO., LTD
◎ Reproduction of the content of this manual in part or in whole is prohibited.
◎ The content of this manual is subject to change without notice.
◎ Every effort has been made in the preparation of this manual. Should you notice any unclear points, omissions, etc., feel free to contact us.
Safety Precautions (Observe Strictly)
■ Before using this product, thoroughly read these "safety precautions" for proper use. After reading, store the precautions in
a safe place.
● These "Safety Precautions" describe instructions that should be observed to prevent damage to property or injury to the
customer or others using the product.
● These instructions are divided into the following categories.
■ Explanation of indications used in this manual
This symbol indicates "the potential and imminent danger of death or serious injury
DANGER
person."
WARNING
This symbol indicates "the possibility of death or serious injury
This symbol indicates "the possibility of personal minor injury
CAUTION
damage (*3) ."
*1 Serious injury: This refers to loss of sight, injury, burns (high- and low-temperature), electric shock, broken bones, injuries
with residual aftereffects from poisoning, etc., and injuries requiring hospital admission for treatment or long
term hospital attendance as an outpatient.
*2 Minor injury: This refers to injuries, burns (high- and low-temperature), electric shock, etc. that do not require hospital
admission for treatment or long-term hospital attendance as an outpatient.
*3 Physical damage: This refers to extended damage to buildings, furniture, livestock, or pets.
■ Explanation of graphic symbols used in this manual
Indicates an action that is not allowed.
Indicates that handling with wet hands is not
allowed.
Indicates that disassembly is not allowed.
■ Precautions common to the main unit, charging equipment, au Micro IC Card (LTE),
peripheral devices
DANGER
Be sure to read the following hazards before use.
Be sure to use only the specified peripheral devices. Use of other devices might cause overheating, ignition, rupture,
fault, or leakage of liquid.
Do not use, store or leave the product in hot places (e.g. by the fire, near a heater, under a kotatsu, in direct sunlight,
in a car in the hot sun). Doing so might cause ignition, rupture, fault, fire or injury.
Before entering an area where flammable gas is generated such as a gas station, be sure to turn off the product and
stop charging the battery. Failure to do so might cause the gas to catch fire.
Do not put the product in a cooking apparatus such as microwave oven or a pressure vessel. Doing so might cause
ignition, rupture, fault, fire or injury.
Do not throw the product into a fire or heat it. Doing so might cause ignition, rupture or fire.
Do not short-circuit the connection terminals. Do not allow conductive foreign objects (metal fragments, pencil leads,
etc.) to come into contact with or get inside the connection terminals. Doing so might cause fire, burns, a fault due to
heat generation.
When using a metal accessory etc., take sure not to allow the metal part come in contact with the connection
terminals or power outlet. Doing so might cause electric shock, ignition, injury or a fault.
The customer is not allowed to disassemble, modify or repair the product. Doing so might cause a fault, ignition,
electric shock, or injury. The Company is not liable even in the event of any nonconformities arising on the product or
PC as a result of modification, etc. Modification of the product is in violation of the Wireless Telegraphy Act.
WARNING
Be sure to read the following warnings before use.
Do not drop or subject to strong impact, such as dropping and throwing. Doing so might cause rupture, overheating,
ignition or a fault.
Do not use outside when you can hear thunder. Doing so might risk lightning strikes and electric shock.
Do not let your hands, fingers and other parts of the body touch the connection terminals. Doing so might cause
electric shock, injury or a fault.
If the product is damaged because it is dropped or something, and its display is cracked or internal parts are
exposed, do not touch the cracked display or exposed parts with your hands. Doing so might cause electric shock or
injury from damaged parts. Contact an au shop or Keitai Guarantee Service Center.
If the wet product is charged, electric shock, short circuit, or corrosion may occur and overheating may cause fire or
malfunction or burns.
Do not splash with water or other liquids. Also, never use in places subject to direct splashing with water or pet urine,
etc. or in humid places such as bath areas, or use with wet hands. Doing so might cause electric shock or fault from
short-circuiting or corrosion of electronic circuits. In the event that the product is splashed with liquid, immediately
disconnect the specified charging equipment's power plug and external devices. Faults caused by wetting with water
or humidity are not covered by the warranty and charges will be incurred for repair.
Do not operate the product while driving an automobile or motorized bicycle, riding a bicycle or walking. Doing so
may compromise traffic safety and cause an accident.
If charging is not completed after the specified charging time, stop charging. Failure to do so might cause leakage of
liquid, overheating, rupture or ignition.
Do not leave in places within the reach of small children. Small children might swallow small parts, etc. by mistake
and choke on them, or might drop them by mistake and cause accidents or injury.
CAUTION
Be sure to read the following cautions before use.
Do not store the product in places subject to direct sunlight (e.g. in automobiles), places that get hot, places that get
extremely cold, and in humid or dusty places. Doing so might cause overheating, ignition, deformation or a fault.
Do not leave on unstable places such as rocky stands or tilting surfaces. Dropping the product may cause injury or
damage. Also, pay sufficient attention to impact, etc.
Do not cover or wrap the product with bedding, etc. while using or charging the product. Doing so might cause a
fire, fault or injury.
Do not touch the main unit or specified charger for a long time while power is being supplied from an external
source. Doing so might cause low-temperature burns.
The product may become hot by prolonged use especially in high-temperature environment. Be careful when using
the product touching your skin for a long time, as it might cause low-temperature burns.
Do not use power outlets or wiring apparatus beyond its rating. Also, exceeding rating, for example, by connecting
multiple devices to a single power strip might cause overheating and fire.
Do not place near corrosive chemicals or in places where corrosive gas is generated. Doing so might cause a fault
or loss of internal data.
Do not leave or store with the Micro IC Card slot cover opened. Doing so might allow dust or other foreign objects to
get inside and cause a fault.
Do not use if there is smoke, abnormal odor or noise, excessive overheating, or other abnormalities. While charging,
disconnect the specified charging equipment, make sure that the product is not overheating, and power off the
product, then contact an au shop or Keitai Guarantee Service Center. Also, if you have dropped or damaged the
product, do not continue to use it in that state, and contact an au shop or Keitai Guarantee Service Center.
When using the specified AC adapter or external device, insert/remove the connector straight to/from the terminal.
Make sure the orientation of the connector is correct. Unless it's correct, it may cause damage or a fault.
Do not charge the battery with W01 Cradle (HWD31PUA) (sold separately) when a cover or case are attached to the
product. Doing so might cause failure of charging, overheating, ignition, or malfunction.
■ Main unit
WARNING
Be sure to read the following warnings before use.
Do not use the product while driving a car or riding a motorbike or bicycle. It may cause a traffic accident. Use of
the product while driving a car or motorbike is prohibited by law. Use of the product while riding a bicycle may be
punishable by some regulations.
Use of electric devices on board is restricted. Follow the instructions of each airline company. Failure to do so may
adversely affect on-board electronic equipment. Doing prohibited use of the electric devices in an aircraft may be
punishable by law.
Follow the instructions of each medical facility for the use of the product on their premises. Failure to do so may
affect electronic equipment and electronic medical equipment.
The product sometimes affects high-precision electronic devices. So, turn it off near such devices. (Examples of
electronic devices that might be affected by the product include cardiac pacemakers, hearing aids, other electronic
medical devices, fire alarms, and automatic doors. If you are using an electronic medical device, contact the device
manufacturer or retailer for information about the possible affect of radio waves.)
When using the product near an implanted pacemaker, implanted cardioverter-defibrillator or other electronic
medical device, radio waves might affect these units and devices. So, please observe the following.
1. Those with an implanted pacemaker or implanted cardioverter-defibrillator should carry or use the product at least
15cm away from the pacemaker or cardioverter-defibrillator.
2. Turn the product off when it may be difficult to keep at least 15cm away such as in a situation you cannot move
freely, since there may be people with a cardiac pacemaker or implanted cardioverter-defibrillator nearby.
3. When a medical institution has laid down designated areas where use of the product is prohibited or is not
allowed to be brought in, abide by the instructions of that medical institution.
4. When using electronic medical devices other than an implanted pacemaker and implanted cardioverter-
defibrillator outside a medical institution (e.g. home medical treatment), check individually with the manufacturer
of the electronic medical device regarding the influence of radio waves.
CAUTION
Be sure to read the following cautions before use.
Use of the product in an automobile sometimes affects on-vehicle electronic devices, though this rarely happens. If
this happens, stop use since this may impair safe travel.
If you feel any abnormality with your skin, immediately consult a dermatologist. Itching, rashes, eczema, etc.
sometimes occurs depending on your physical constitution and condition.
The materials of parts used on the product are as follows.
Part
Display panel (Touch panel)
Exterior case
Power button
Micro IC Card slot cover
Do not allow liquids, metal pieces, burnable items, and other foreign matter to get inside the external connection
terminal and Micro IC Card slot. Doing so might cause fire, electric shock, a fault or injury.
Use the product with the Micro IC Card slot cover closed. If the covers are open, dirt or water may get inside
causing a fault.
Do not put the product directly on sand at a beach, etc. Sand or other small particles might get inside the product
through the external connection terminal causing overheating or a fault.
When using the product for data communication, be careful not to keep the product in direct contact with your skin
for a prolonged period, or not to cover the product with paper, cloth, bedding, etc. The main unit might get hot,
causing fire, injure, burns or a fault.
■ Internal Battery
(The internal battery of the product is a lithium-ion battery)
The internal battery is not fully charged at the time of purchase. Charge the battery before using the
product.
Notes on usage
(*1) to a person."
(*2) to a person or physical
Indicates that use in a place where the product is
likely to get wet or allowing the product to get wet is
not allowed.
Indicates an action that must be done.
Indicates that the power plug must be disconnected
from the power outlet.
Material <Surface treatment>
Glass
PC resin <coating>
PC resin <coating> TPU resin
Outside: PC resin <coating> Inside: TPU resin
DANGER
Be sure to read the following hazards before use.
If the leaked liquid gets on your skin or clothes, immediately rinse it off with water to avoid injury. If the liquid gets
into your eyes, do not rub, but after wash your eyes with water, and immediately consult a doctor to avoid the risk of
losing your eyesight. If the liquid gets on a device, wipe it off without touching it.
Internal battery is a consumable item. If the performance of an internal battery does not recover (e.g. the usable
time after each charge has become extremely short), the internal battery is at the end of service life, so stop use.
Failure to do so might cause overheating, ignition, rupture or liquid leakage. Since the battery is built-in, au Shop will
keep the product and charges will be incurred for repair. You may not use the product for a certain period. Please be
forewarned. Note that the length of service life varies depending on the usage condition, etc.
■ Charging equipment
WARNING
Be sure to read the following warnings before use.
Do not use at other voltages than the specified power supply voltage. Doing so might cause an ignition, fire,
overheating, electric shock, or injury.
• AC adapter: 100 – 240V AC
Firmly insert the power plug of the specified charging equipment into the power outlet down to the base of its pins.
Incomplete insertion of the power plug might result in electric shock, overheating, fire or injury. Do not use damaged
charging equipment or loose power outlets.
Do not damage, modify, twist, pull or place a heavy object on the power cable of the specified charging equipment
(sold separately). Do not use a damaged cable. Doing so might cause an electric shock, injury, short circuit or fire.
Do not let your hands, fingers and other parts of the body touch the connection terminals. Doing so might cause
electric shock, injury or a fault.
If you hear thunder, do not touch the power plug. Doing so might cause an electric shock as a result of a lightning
strike.
When cleaning, remove the specified charging equipment's power plug from the power outlet. If the plug remains
plugged in when you clean the equipment, it might cause an electric shock or short-circuit.
Wipe off the dust on the power plug. Failure to do so might cause fire, burns or electric shock.
When not using the product for a long while, remove the specified charging equipment's power plug from the power
outlet. Failure to do so might cause fire or a fault.
Do not use in places subject to splashing with water, pet urine or other liquids. Doing so might cause overheating, fire,
electric shock or fault from short-circuiting or corrosion of electronic circuits. In the event that the product is splashed
with liquid, immediately disconnect the specified charging equipment's power plug.
CAUTION
Be sure to read the following cautions before use.
Do not use in humid places such as bath areas, or connect/disconnect the specified charging equipment with wet
hands. Doing so might cause electric shock, injury or a fault.
Charge the battery in a stable place especially while the vibration mode set. If placed on an inclined surface or
(*1) to a
wobbly stand, the product might fall causing injury or damage. In addition, do not cover or wrap the product with a
cloth or bedding. Doing so might cause a fire, fault or injury.
Hold the power plug of the specified charging equipment when removing from an outlet. If you pull the cable, the
cable might be damaged.
If you feel any abnormality with your skin, immediately consult a dermatologist. Itching, rashes, eczema, etc.
sometimes occurs depending on your physical constitution and condition.
The materials of parts used on the supplied AC adapter/microUSB cable (HWD14PQA) are as follows.
Part
Exterior case
Power plug
USB cable
USB plug (Shield)
USB plug (Resin part)
microUSB plug (Shield)
microUSB plug (Resin part)
■ au Micro IC Card (LTE)
WARNING
Be sure to read the following warnings before use.
Do not put the au Micro IC Card (LTE) in a cooking apparatus such as a microwave oven or a pressure vessel. Doing
so might cause melting, overheating, fuming, loss of data or a fault.
CAUTION
Be sure to read the following cautions before use.
Be careful when attaching/removing the au Micro IC Card (LTE). Doing so might injure your hands or fingers.
Use only the devices specified by the Company to insert the au Micro IC Card (LTE) in. Using a device not specified
by the Company might cause loss of data or a fault. For the specified devices, contact an au shop or Customer
Service Center.
Do not disassemble or modify the au Micro IC Card (LTE). Doing so might cause loss of data or a fault.
Do not use or leave the au Micro IC Card (LTE) in hot places such as by the fire or a heater. Doing so might cause
melting, overheating, fuming, loss of data or a fault.
Do not throw the au Micro IC Card (LTE) into a fire or heat it. Doing so might cause melting, overheating, fuming, loss
of data or a fault.
Do not touch the IC (metal) part of the au Micro IC Card (LTE) or short-circuit it. Doing so might cause loss of data or
a fault.
Do not drop the au Micro IC Card (LTE) or subject it to strong impact. Doing so might cause a fault.
Do not fold, bend or place a heavy object on the au Micro IC Card (LTE). Doing so might cause a fault.
Do not wet the au Micro IC Card (LTE). Doing so might cause a fault.
Do not scratch the IC (metal) part of the au Micro IC Card (LTE). Doing so might cause a fault.
Do not store the au Micro IC Card (LTE) in dusty places. Doing so might cause a fault.
Do not store the au Micro IC Card (LTE) in places exposed to direct sunlight or hot and humid places. Doing so
might cause a fault.
Store the au Micro IC Card (LTE) out of reach of small children. Failure to do so might cause injury, etc. if they
accidentally swallow and choke on it.
Handling precautions
These precautions are provided to ensure that performance can be fully demonstrated. Thoroughly read these precautions to
ensure correct use.
■ Precautions common to the main unit, charging equipment, au Micro IC Card (LTE),
peripheral devices
● Do not apply excessive force to the product during use. Be sure not to put the product into a tightly packed bag or place
a heavy object on the product in a bag. Sitting on the product in your pocket might damage the display or internal circuit
board resulting in a malfunction.
Keeping an external device connected to the external connection might damage the connector resulting in a malfunction.
Such damage and malfunction are not covered by the warranty, even if there is no external damage.
● Do not use the product in extremely hot, cold or humid places. (Use within an ambient temperature range of 5°C to 35°C
and humidity range of 35% to 85%.)
● Do not use in places subject to lots of dust or vibration.
● Clean the connection terminals with dry cotton swabs, etc. every now and then. Soiled terminals might cause poor
connection. Do not exert a strong force to clean the connection terminals to prevent deformation.
● Clean the product with a dry soft cloth (such as the type used for eyeglasses). Forceful rubbing with a dry cloth may
scratch the display. The display may be stained if splash or smear is left attached to the surface. Wiping the product
using alcohol, thinner, benzine, detergent, etc. might erase the printing on the outer casing or cause discoloration.
● Use as far away as possible from land-line phones, TVs and radios. Use nearby might affect them.
● The product may become warm while charging or communicating, depending on the situation, but this is not abnormal.
Note that there are times when it comes to use the product in a bag or bag heat up, the temperature of the product is
increased.
● When the product is used by a child, parents or guardians should thoroughly read the "Instruction Manual" and teach the
child how to use it.
■ Main unit
● Do not forcefully press, tap or intentionally subject the display to strong impact. Doing so might cause scratching or
damage.
● Do not forcefully press your fingernails, sharp objects or hard objects against keys or display surface. Doing so might
cause scratching or damage.
The touch panel is designed to be lightly touched by fingers. Do not apply strong pressure with your fingers or sharp-
pointed objects (such as fingernails, ballpoint pens and pins) on the touch panel.
In the following cases, the product may not respond to touching the touch panel, or errors in operation may occur.
• Operation with gloved hands
• Operation with fingernails
• Operation with foreign object on the screen
• Operation with protective sheet or seal on the screen
• Operation with a water drops or dew condensation attached on the touch panel
• Operation with wet or sweaty fingers
● Never use the modified product. Use of a modified device violates the Radio Law.
This product has acquired the certification of conformity with technical regulations for the specified radio station based on
the Radio Law, and you can check "Technical Conformity Mark
"Settings"→"About"→"Certification" to display) as a certificate. If the screws of the product are removed and modifications
are made to the internal components, the certification of conformity with technical regulations will become invalid. Never
use the product without the valid certification. Doing so violates the Radio Law.
● To prevent unlawful modification, the product has been designed so that it cannot be easily disassembled. Modifying the
product is prohibited by the Radio Law.
● Contents saved in this product might be altered or lost in an accident, fault, repair or mishandling. Be sure to keep a copy
of important contents. Note that Company assumes no responsibility for any damages or lost profits resulting from altered
or lost contents.
● This product uses liquid crystal for its display. The display response speed may become slow when the ambient
temperature is low, which is due to the property of liquid crystal and not a malfunction. The display response speed will
return to normal at room temperature.
● Although the display used on the product is made using high-precision technology, some pixels (dots) might be lit or out
at all times. This is not a malfunction.
● Take care not to inconvenience people around you when you use the product in a public place.
● Take care not to place magnetized items such as magnetic cards, speakers and TV sets near the product, as it might
cause malfunction.
Putting a strong magnetism close to the product might cause false operation.
● When you put the product in your pocket or bag, take care so that the display does not come in contact with metal objects
or other hard objects, as it might cause scratching or damage. Doing so might cause scratching or damage.
● When suddenly brought into a warm place from a cold place, or when in a humid location, or when used where
temperature suddenly changes (e.g. near the air discharge port of an air conditioner), water droplets (i.e. condensation)
sometimes are formed inside the product. Note that when used under conditions such as this, the humidity might cause
corrosion or a fault.
● When wiping the display, wipe with a soft, dry cloth. Use of a moistened cloth, glass cleaner or other similar liquid might
cause a fault.
● When connecting/disconnecting an external device to/from the external connection terminal, make sure that the external
connection terminal is horizontal with the external device.
● Note that applying unnecessary force with the external connection terminal connected to the external device might cause
damage.
● Do not discard the product together with regular trash. Please cooperate in the collection of the product when it is no
longer needed to protect the environment and effectively use resources. Old products are collected at au shops and other
places.
● Insert only an au Micro IC Card (LTE) into the Micro IC Card slot on the product.
● Note that pulling strongly or applying unnecessary force with Micro IC Card slot cover might cause damage.
■ Touch Panel
● Use your finger to operate the touch panel. Do not use ballpoint pens, pencils or other sharp-pointed objects. Using such
objects does not only hinder correct operation of the touch panel, but also might cause scratching or damage to the
display.
● Do not put stickers or sheets (e.g. commercially available protective films, peep prevention sheets) on the display. Doing
so might hinder correct operation of the touch panel.
● Do not operate the touch panel with fingernails. Doing so might result in split nails or jammed fingers.
● If the display surface is dirty or wet with sweat or water, it may not function correctly. In such case, wipe the display
surface with a dry, soft cloth.
● Press the touch panel strongly may cause damage or malfunction.
● When carrying the product in your pocket or bag, take care not to put the touch panel close to metals or other conductive
materials, as it might cause false operation of the touch panel.
Material <Surface treatment>
PC resin
Copper alloy <Nickel plating>
PVC resin
Iron <Nickel plating>, PBT resin
PVC resin
Stainless <Nickel plating>, LCP resin
PVC resin
" from the "Certification" screen (in Home screen, tap