Step 3: Connecting The Video Cords; Step 4: Connecting The Audio Cords - Sony DVP-K88P Service Manual

DVP-K88P/K88PM

Step 3: Connecting the Video Cords

Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver).
In order to view progressive signal (525p or 625p) pictures with a compatible TV, projector, or
monitor, you must use pattern B.
A
(yellow)
INPUT
VIDEO
L
AUDIO
R
TV, projector, or AV
amplifier (receiver)
COAXIAL
R-AUDIO-L
OPTICAL Y P /C
B B P /C R
DIGITAL OUT COMPONENT VIDEO OUT
(green) (blue) (red)
Component video
cord (not supplied)
l : Signal flow

Step 4: Connecting the Audio Cords

Select one of the following patterns A or B, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
This will enable you to listen to sound.
(red)
(white)
(yellow)*
LINE OUT
VIDEO
R-AUDIO-L
COAXIAL
R-AUDIO-L
OPTICAL Y P B /C B
DIGITAL OUT COMPONENT VIDEO OUT
to DIGITAL OUT (COAXIAL or OPTICAL)
COAXIAL
OPTICAL
DIGITAL OUT
Optical digital cord (not supplied)
to optical
[Speakers] digital input
Rear (L)
Front (L)
Centre
: Signal flow
* The yellow plug is used for video signals (page 15).
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
Audio/video
cord (supplied)
(yellow)
to LINE OUT (VIDEO)
LINE OUT
VIDEO
R
to COMPONENT CD/DVD player
VIDEO OUT
COMPONENT
VIDEO IN
Y
(green)
P /C
B B
(blue)
P /C
R R
(red)
TV, projector, or AV
amplifier (receiver)
,continued
A
(yellow)*
INPUT
Audio/video
VIDEO
cord (supplied)
(white)
L
(red) AUDIO
R
TV, projector, or AV
amplifier (receiver)
to LINE OUT L/R (AUDIO)
LINE OUT
VIDEO
P /C R R
CD/DVD player
or
Coaxial digital cord
(not supplied)
to coaxial
B
digital input [Speakers]
Rear (R)
Front (R)
AV amplifier (receiver)
with a decoder
Subwoofer
,continued
A If you are connecting to a video input jack
Connect the yellow plug of an audio/video cord (supplied) to the yellow (video) jack. You will
enjoy standard quality images.
B
If you are connecting to a monitor, projector, or AV amplifier
(receiver) having component video input jacks (Y, P
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, use this connection and set
"PROGRESSIVE (COMPONENT OUT)" in "SCREEN SETUP" to "ON" (page 70) to output
progressive signals.
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see
page 69.
To change the colour system
If the on-screen menu of the player does not appear on the connected TV, switch the player's
colour system to match the colour system of the TV (NTSC or PAL).
First turn off the player by pressing "/1, and then press "/1 again while holding down x on the
player. The player turns back on, and the name of the colour system scrolls across the front panel
display.
B
Note
Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR, you
may not receive a clear image on the TV screen. If your TV has only one audio/video input jack, connect the
player to this jack.
15 16
A
Connecting to audio L/R input
jacks
This connection will use your TV's or stereo
amplifier's (receiver's) two speakers for
sound. Connect using the audio/video cord
(supplied).
Yellow
White (L)
Red (R)
• Surround effect (page 47)
TV: Dynamic Theatre, Dynamic, Wide,
Night
Stereo amplifier (receiver): Standard, Night
17 18
1-4
Yellow Yellow
White (L) White (L)
Red (R)
Red (R)
/C
B
Green Green
Blue
Blue
Red
Red
VCR
CD/DVD player
TV
Connect
directly
B
Connecting to a digital audio
input jack
If your AV amplifier (receiver) has a Dolby*
2
Digital, DTS* , or MPEG audio decoder and
a digital input jack, use this connection.
Connect using a digital optical or coaxial cord
(not supplied).
Yellow
Coaxial cord
White (L)
Red (R)
Optical cord
• Surround effect
Dolby Digital (5.1ch), DTS (5.1ch), MPEG
audio (5.1ch)
*1
Manufactured under license from Dolby
Laboratories.
"Dolby", "Pro Logic", and the double-D symbol
are trademarks of Dolby Laboratories.
*2
"DTS" and "DTS Digital Out" are trademarks of
Digital Theater Systems, Inc.
Notes
• After you have completed the connection, make
the appropriate settings in Quick Setup (page 19).
If your AV amplifier (receiver) has an MPEG
audio decoder function, set "MPEG" to "MPEG"
in AUDIO SETUP (page 73). Otherwise, no
sound or a loud noise will come from your
speakers.
• The TVS effects of this player cannot be used
with this connection.
• In order to listen to DTS sound tracks, you must
use this connection. DTS sound tracks are not
output through the LINE OUT L/R (AUDIO)
jacks, even if you set "DTS" to "ON" in Quick
Setup (page 19).
, P /C )
B R R
1