Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. Contents Packing list ------------------------------------------------------ Precautions ------------------------------------------------------ Installation Instructions -------------------------------------- Swivel Base ---------------------------------------------------- Power cord --------------------------------------------------- Video cable --------------------------------------------------- Operating Instructions --------------------------------------- General Instructions --------------------------------------- Front panel control ----------------------------------------- How to adjust a setting ------------------------------------ Adjusting the picture ---------------------------------------...
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
INSTALLATION INSTRUCTIONS Swivel Base To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. ( see figure 1 ) • Locate the cavities at the bottom front of the monitor. •...
Page 5
Connecting the Video Cable: the monitor comes with a built-in video cable. Plug the signal cable′s 15-pin connector into the computer's video port and tighten the two screws on the cable connector.(see figure 2) Caution:Don’t bend the signal cable, otherwise it will break the inner wire. Connecting the Power Cord: Plug the power cord into the monitor's AC power jack.
OPERATING INSTRUCTIONS General Instructions The power switch is located at front panel of the monitor. Press the power switch to turn the monitor on or off. the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. •...
FRONT PANEL CONTROL • Power Press this knob to switch ON/OFF of monitor’s power. • MENU Active OSD menu or function adjust confirm. • Contrast Adjust contrast or function adjust. • Brightness Adjust brightness or function adjust. • EXIT Exit a function or inactive OSD menu. •...
How to adjust a setting The monitor controls are accessed by pressing button MENU to enable OSD (On-Screen-Display). The main menu will be displayed as follows. Figure 4 Note: If adjustment or selection of any OSD menu is not made for more than 10 seconds, the current setup will be saved and the OSD will disappear automatically.
Page 9
10. PIN-BALANCE Adjust to compensate the pincushion unbalance. 11. PARALLELOGRAM Adjust the picture to be a rectangle. 12. ROTATION Adjust the picture tilt to horizontal position. 13. 6500K /9300K (COLOR TEMPERATURE) The color temperature for 6500°K is x=0.313, y=0.329 and 9300°K is x=0.283, y=0.297.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green Monitor standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and the Swedish Confederation Employees ( NUTEK ).
TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Picture is fuzzy Picture bounces or a wave pattern is present in the picture The power LED is ON (orange) but there’s no video or no picture.
APPENDIX A - SPECIFICATIONS 43.2cm(17"), pure flat and 90º deflection, 29mm neck, 0.25mm dot pitch non-glare screen. Viewable Image Size 40.6cm (16"), diagonal Display Color • Analog input Unlimited colors Input Signal All timing that meets scanning frequencies Specification • Video •...
Page 14
STANDARD RESOLUTION 720 x 400 640 x 480 VESA/85 640 x 480 VESA/85 800 x 600 VESA/85 1024 x 768 VESA/85 1280 x 960 VESA/85 1280 x 1024 VESA/75 1600 x 1200 HORIZONTAL VERTICAL FREQUENCY FREQUENCY 31.5kHz 70Hz 31.5kHz 60Hz 43.3kHz 85Hz 53.7kHz...