Page 2
Copyright 2009 All rights Reserved Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.
Detach and store implements in a wheels. This could result in injury area where children normally do or equipment damage. not play. Secure implement by Do not carry passengers on using blocks and supports. implement at any time. 2/16/09 RTR2570 Rotary Tillers 311-251M...
Page 4
Work in a clean dry area. debris. equipment. Lower the implement to the Remove all tools and unused ground, put tractor in park, turn off parts from implement before engine, and remove key before operation. performing maintenance. RTR2570 Rotary Tillers 311-251M 2/16/09...
Page 5
Wear protective gloves and safety glasses or goggles when working with hydraulic systems. If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be treated within a few hours or gangrene may result. 2/16/09 RTR2570 Rotary Tillers 311-251M...
Safety Labels make sure the correct safety labels are included in the request. To order new labels go to your Land Pride dealer. Your tiller comes equipped with all safety labels in place. 5. Refer to this section for proper label placement.
Page 7
Table of Contents Land Pride Important Safety Information 22228 818-540C Shield missing - Do Not operate. 22228 ROTATING DRIVELINE KEEP AWAY! 818-552C Rotating Driveline Hazard - Keep Away! 22236 2/16/09 RTR2570 Rotary Tillers 311-251M...
Page 8
Table of Contents Land Pride Important Safety Information 22236 818-350C General Safety Instructions RTR2570 Rotary Tillers 311-251M 2/16/09...
Refer to Figure 1 for the location The Model RTR2570 Reverse-Till Rotary Tiller is of your serial number plate. designed and built by Land Pride to till the soil for seedbed or planting preparation. The Model RTR2570 is adapted for 540rpm PTO and three-point hitch Category 1 mounting.
Refer to “Torque Values Chart” on page 25 to determine operator’s manual. the correct torque value when tightening hardware during assembly. 22237 Hitch Assembly Figure 1-1 RTR2570 Rotary Tillers 311-251M 2/16/09...
Page 11
Failure to install front deflector guides will result in damage (#3) in slot and hold in place with clip (#4). to the front deflector! 3. Secure with plate (#5) and lock nut (#6). 19122 Spring Tines Figure 1-2 2/16/09 RTR2570 Rotary Tillers 311-251M...
Pull Collar Coupling With Slip Clutch Protection CAUTION Tractor PTO shield and all tiller guards must be in place at all times during operation! 22235 Pull Collar Coupling Figure 1-5 Tractor Hook-Up 22238 Figure 1-3 RTR2570 Rotary Tillers 311-251M 2/16/09...
Page 13
PTO shaft. Securely block Rotary Tiller up in this position. f. Remove all burrs and cuttings. 2. Place tractor gear selector in park, shut tractor engine off, set park brake and remove switch key. 2/16/09 RTR2570 Rotary Tillers 311-251M...
Page 14
10. Raise and lower implement to find the maximum possible extended driveline length. Check to make 14706 certain that the driveline has not extended beyond the maximum allowable length recorded in step 3. Down Pressure Kit Figure 1-10 RTR2570 Rotary Tillers 311-251M 2/16/09...
NOTE: Too much pressure will cause premature wear on the rear deflector. IMPORTANT: Be sure both skid shoes are adjusted the same. 12003 11136 Raised Position Figure 3-4 Skid Shoe Adjustment Figure 3-2 2/16/09 RTR2570 Rotary Tillers 311-251M...
Be sure to ask how close Make all hydraulic adjustments from the tractor seat. Never you can work to the marks or flags they positioned. make adjustments while standing along side the tractor or behind the tractor. RTR2570 Rotary Tillers 311-251M 2/16/09...
With a little practice and a few adjustments, you will soon 9. After tilling the first 50 feet, stop and check to see that be achieving the results you want with your Land Pride the tiller is adjusted properly. Rotary Tiller.
Follow run-In, disassembly and assembly instructions for Replace any worn, damaged or illegible safety labels by your specific clutch. obtaining new labels form your Land Pride Dealer. Clutches With 4 Adjusting Nuts Tine Replacement Clutch Run-In...
Page 20
4. Inspect all components and replace to their original Figure 4-4 position. Make certain stop flange (#3) is replaced with its flanges down as shown. 5. Fully tighten all 8 Alan head socket bolts (#2). RTR2570 Rotary Tillers 311-251M 2/16/09...
Page 21
6. Replace all damaged or missing decals. 7. Repaint parts where paint is worn or scratched to prevent rust. Ask your dealer for Aerosol Land Pride touch-up paint. They are also available in touch-up bottles with brush, quarts and gallon sizes by adding TU, QT or GL to the end of the Aerosol part number.
Grease bearing on right end of tines until grease starts to purge from the relief hole in the bearing mount casting on the inside of the tiller end plate. Type of grease = Multi-Purpose 14759 Quantity = Coat Generously RTR2570 Rotary Tillers 311-251M 2/16/09...
Page 23
Fill if necessary with gear lube 80-90W EP and retighten plug. IMPORTANT: Should your gearbox require repair, take it to your Land Pride Dealer! Check the oil level in the gearbox at least every 50 hours of operation. 14200...
Formed steel gives the rear deflector additional strength. Springs allow deflector to springs bounce as it hits obstructions. Front deflector plate Front deflector plate is flexible to take the beating rocks or debris will give it. 2/16/09 RTR2570 Rotary Tillers 311-251M...
This Warranty does not apply to any part or product which in Land Pride’s judgment shall have been misused or damaged by accident or lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or which has been used for a purpose for which the product is not designed.