ION Sound Splash FM Quick Start Manual

Box Contents: Sound Splash FM, Micro USB Charging Cable, Quickstart Guide.
Support: For the latest information about this product (system requirements, compatibility information, etc.) and product registration, visit ionaudio.com.
For complete warranty information, visit ionaudio.com/warranty. For the complete multilingual User Guide, visit ionaudio.com.
WARNING: Keep any non-water-resistant devices (phones, music players, etc.) in a dry place where they will not be affected by water and cause a risk of electric shock.
Features:
1. Hook - Use this to hang Sound Splash FM from a shower head or shower stall.
2. Speaker - Listen to music or a phone call from this full range speaker.
3. Bluetooth LED - This blinks blue when Bluetooth pairing or illuminates solid blue when connected to a Bluetooth
device.
4. FM Radio LED - This illuminates solid green when FM radio is selected as the source. When a radio station is
selected, a voice prompt will be heard identifying the station.
Note: When a voice prompt is playing, the FM signal will be temporarily muted.
5. Volume Down - Decreases the speaker volume on Sound Splash FM.
6. Power On/Off / Source - Press and hold this button for 2-3 seconds to power Sound Splash FM on/off. When
powered on, press and release this button to select the source between Bluetooth and FM radio.
7. Volume Up - Increases speaker volume on Sound Splash FM.
8. Previous Track / Tune – - Press and release this button to select a previous FM radio station Press and hold this
button to seek backwards for a FM radio station. When Bluetooth is the source, press and release to select the
previous track.
9. Bluetooth / Call Receive / Call End / Play / Pause / Bluetooth Disconnect / Radio Preset Mode - Press and
hold this button for 2 seconds to unpair from a connected Bluetooth device, and to make it available to pair with
other devices. If you do not unpair your device, Sound Splash FM will "remember" your device even if it is
powered off then on again. When a paired smartphone receives a phone call, press this button to answer the call;
press it again to disconnect the call. The Bluetooth disconnect function will be disabled when a phone call is
ringing or connected. Press and release this button to select a previously saved preset station. In FM mode, press
and hold this button for 3 seconds to enter Preset mode.
10. Next Track / Tune + - Press and release this button to go to the next FM radio station or to skip to the next
Bluetooth track. When connected to a smartphone through Bluetooth, access your device's personal assistant by
pressing and holding this button for 3 seconds. This feature may not be compatible with all smartphones. In Radio
Mode, press and hold this button to seek forward for a FM radio station.
11. Microphone - Talk into this after receiving a call.
12. Micro USB Port - Open the bottom cover to access the USB port. Use the included USB cable to connect this to
a USB port on your computer or phone charger to recharge Sound Splash FM's battery.
13. Suction Cups - Attach these to the back of Sound Splash FM and then to a surface.
Note: Attach the suction cups to a solid, non-porous surface for an airtight seal. Glass, metal, smooth tile, and
polished wood are surfaces where suction cups stick best.
Sound Splash LED Activity:
Blinking Blue LED = Bluetooth pairing mode
Solid Blue LED = Connected to a Bluetooth device
Blinking Red LED = Low battery on Sound Splash FM
Solid Red LED = Battery is charging
Solid Green LED = FM is selected as the source
Blinking Green LED = Preset Save mode (slow flash) and preset saved confirmation (4 quick flashes)
Bluetooth Pairing:
1. Press and hold Sound Splash FM's Bluetooth/Play/Pause button for 2 seconds to power it on.
2. If the blue Bluetooth LED is blinking, then Sound Splash is ready to pair/connect. Proceed to Step 3. If the LED is solid blue, Sound Splash FM is already
connected to another device. To connect to a new device, disconnect the other device through that device's settings menu or by holding down the Play/Pause
button for 2 seconds. If the green LED is lit, you are in FM mode, not Bluetooth mode. Press the Power/Source button once to switch to Bluetooth mode.
3. On your device, turn Bluetooth on.
4. On your device, Sound Splash FM will appear as an available Bluetooth device. Tap it to select it. The Bluetooth LED will be solid blue after a connection has
been made.
5. If your device requires a passcode or PIN, enter the number zero ("0") four times.
6. To reset Bluetooth connections to pair with another device, hold down the Bluetooth/Play/Pause button for 2 seconds.
Note: If you are in Bluetooth Pairing mode, Sound Splash FM will power off if there is no Bluetooth connection after 5 minutes.
Using the Phone:
Note: You must power on and pair Sound Splash FM with your Bluetooth device before using it to listen to music or as a speakerphone.
When you have an incoming call, Sound Splash FM's speaker will play a ringtone.
1. To answer the call, press Sound Splash FM's Call Receive button.
Note: If you get an incoming call during music playback, the music will pause until you end the call.
2. Speak into the microphone (located below the Play/Pause button) and adjust the call volume using the Volume buttons.
3. To end the call, press the Call End button.
Saving a Preset Radio Station:
1. Press the Source button to choose FM Radio. The FM LED will illuminate solid green.
2. Press and release the Tune – or Tune + buttons to select a FM radio station that you want to save as a preset. A voice prompt will be heard identifying the
selected station.
3. Press and hold the Play/Pause button for 3 seconds to enter Preset Creation mode.
4. Press and release the |>> button to select from one of the 6 preset locations. For each button press of |>>, the unit will say the active preset number (for
example, "two"). Once the desired save location is reached, press and release the Play/Pause button to save the station preset. The FM LED will show 4
quick green flashes to confirm a preset is saved and then exit Preset Save mode and return to FM mode.
5. To select from the 6 Preset stations, press and release Play/Pause in FM radio mode. The tuner will jump to the next preset location and say the name
of the preset location (for example, "three"), and resume playing the FM station audio.
Note: When audio tones are playing, the FM signal will be temporarily muted.
Technical Specifications
Audio Output Power: 1.5 W
Output Power: 1.5 W
Power: Rechargeable lithium-ion battery
Water resistant class: IPX4 (protected from splashing water but is not submersible
Supported Bluetooth Profile: A2DP, HFP, AVRCP
Bluetooth Range*: 30 ft. (9.1 meters)
Battery: Battery life**: 20 hours; Recharge time: Approximately 2 hours
Dimensions (width x depth x height): 2.9" x 4.5" x 1.6" (74 mm x 114 mm x 41 mm)
Weight: 0.3 lbs. (0.1 kg)
Specifications are subject to change without notice.
* Bluetooth range is affected by walls, obstructions, and movement.
** Battery life may vary based on temperature, age, and volume usage of product.
Sound Splash FM
Quickstart Guide
Manual Version 1.0
1
2
3
4
6
7
5
8
10 10
9
11 11
12
12