Honeywell RXSW100A3CULH Owner's Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Switch
  5. RXSW100A3CULH
  6. Owner's manual

Honeywell RXSW100A3CULH Owner's Manual

Automatic transfer switch
Hide thumbs
Table of Contents

Advertisement

Quick Links

Para español, visita:
http://www.honeywellgenerators.com/service-support/owner-support
Pour le français, visiter :
SAVE THIS MANUAL FOR FUTURE REFERENCE
Owner's Manual
Automatic Transfer Switch
100 & 200 Amp, Service Entrance, CSA
Model Number
RXSW100A3CULH
RXSW200A3CULH
SERIAL NUMBER: _________________________
DATE PURCHASED:________________________
WWW.HONEYWELLGENERATORS.COM
http://www.honeywellgenerators.com/service-support/owner-support
For
855-436-4636

Advertisement

Table of Contents
loading

Related Manuals for Honeywell RXSW100A3CULH

Summary of Contents for Honeywell RXSW100A3CULH

  • Page 1 Owner’s Manual Automatic Transfer Switch 100 & 200 Amp, Service Entrance, CSA Model Number RXSW100A3CULH RXSW200A3CULH SERIAL NUMBER: _________________________ DATE PURCHASED:________________________ WWW.HONEYWELLGENERATORS.COM 855-436-4636 Para español, visita: http://www.honeywellgenerators.com/service-support/owner-support Pour le français, visiter : http://www.honeywellgenerators.com/service-support/owner-support SAVE THIS MANUAL FOR FUTURE REFERENCE...
  • Page 2 WARNING Operating, servicing and maintaining this equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your equipment in a well-ventilated area and wear gloves or wash your hands...

  • Page 3: Table Of Contents

    Table of Contents Section 1: Safety Section 4: Operation Introduction ............1 Functional Tests and Adjustments ....15 Safety Rules ............1 Manual Operation ..........15 Close to Utility Source Side ........15 Safety Symbols and Meanings ......1 Close to Generator Source Side .......16 Electrical Hazards ..........2 Return to Utility Source Side ........16 General Hazards ..........3...
  • Page 4 This page intentionally left blank. Automatic Transfer Switch Owner’s Manual...

  • Page 5: Section 1: Safety

    Safety Section 1: Safety Introduction Safety Rules Thank you for purchasing a Honeywell, Inc. product. This The manufacturer cannot anticipate every possible unit has been designed to provide high performance, circumstance that might involve a hazard. The warnings efficient operation, and years of use when maintained in this manual, and on tags and decals affixed to the unit properly.

  • Page 6: Electrical Hazards

    Safety Electrical Hazards DANGER DANGER Electrocution. High voltage is present at Equipment malfunction. Installing a dirty or damaged transfer switch and terminals. Contact with live transfer switch will cause equipment malfunction and terminals will result in death or serious injury. will result in death or serious injury.

  • Page 7: General Hazards

    Safety General Hazards DANGER DANGER Electrocution. In the event of electrical accident, Electrical backfeed. Use only approved switchgear to immediately shut power OFF. Use non-conductive isolate generator from the normal power source. implements to free victim from live conductor. Apply Failure to do so will result in death, serious injury, first aid and get medical help.
  • Page 8 Safety This page intentionally left blank. Automatic Transfer Switch Owner’s Manual...

  • Page 9: Section 2: General Information

    General Information Section 2: General Information Unpacking This transfer switch is suitable for control of motors, electric discharge lamps, tungsten filament and electric heating Carefully unpack the transfer switch. Inspect closely for equipment where the sum of motor full load ampere ratings any damage that might have occurred during shipment.

  • Page 10: Utility Service Circuit Breaker

    General Information Transfer Switch Enclosure Utility Service Circuit Breaker The standard switch enclosure is a National Electrical The utility service and generator disconnect circuit Manufacturer’s Association (NEMA) and UL/CUL 3R breakers for 100 amp models are: type. UL/CUL and NEMA 3R (indoor/outdoor rated) type •...

  • Page 11: Smart A/C Module (Sacm)

    General Information Smart A/C Module (SACM) Up to four air conditioner loads can be managed by the SACM. The SACM manages the loads by “shedding” the connected loads in the event of a drop in generator frequency (overload). Loads to be “shed” are in 4 priority levels on the module.
  • Page 12 General Information This page intentionally left blank. Automatic Transfer Switch Owner’s Manual...

  • Page 13: Section 3: Installation

    Installation Section 3: Installation Introduction to Installation Install the transfer switch as close as possible to the electrical loads that are to be connected to it. Mount the This equipment has been wired and tested at the factory. switch vertically to a rigid supporting structure. To prevent Installing the switch includes the following procedures: switch distortion, level all mounting points.

  • Page 14: Connecting Power Source And Generator Power Supply

    Installation Connecting Power Source and Generator Power Supply DANGER Electrocution. Turn utility and emergency power supplies to OFF before connecting power source and load lines. Failure to do so will result in death or serious injury. (000116) Installation and interconnection diagrams are provided in this manual.

  • Page 15: Connecting Start Circuit Wires

    Installation Connecting Start Circuit Wires Connecting SACM Control system interconnections consist of N1, N2, and Figure 3-3. The SACM can control an air conditioner T1, and leads 23, 0, and 194 (see Figure 3-3). The (24 VAC) directly. generator control wiring is a Class 1 signaling circuit. Reference instruction manual...
  • Page 16 Installation Thermostat 1 Air Conditioner 1 Thermostat 2 Air Conditioner 2 Thermostat 3 Air Conditioner 3 Thermostat 4 Air Conditioner 4 0 DC GROUND 194 +12 VDC T1 (fused) 23 TRANSFER Battery Charge Replace with Littelfuse 021606.3XHP, ® Optifuse FCD-6.3A or ®...

  • Page 17: Auxiliary Contact

    Installation Auxiliary Contact Fault Current Label Figure 3-4. If desired, there is one normally-closed Figure 3-5. A Fault Current Identification Label is Auxiliary Contact (A) on the transfer switch to operate provided in the bag containing the unit Owner’s Manual and customer accessories, remote advisory lights, or remote transfer switch manual operating handle.
  • Page 18 Installation This page intentionally left blank. Automatic Transfer Switch Owner’s Manual...

  • Page 19: Section 4: Operation

    Operation Section 4: Operation Functional Tests and Adjustments CAUTION Following transfer switch installation and interconnection, inspect the entire installation carefully. A competent, Equipment damage. Do not use excessive force while qualified electrician should inspect it. The installation manually operating the transfer switch. Doing so could should comply strictly with all applicable codes, result in equipment damage.

  • Page 20: Close To Generator Source Side

    Operation Close to Generator Source Side Generator Voltage Checks Before proceeding, verify the position of the switch by 1. On the generator panel, select the MANUAL mode observing the position of the manual operation handle in of operation. The generator should crank and start. Figure 4-1.

  • Page 21: Checking Automatic Operation

    Operation 5. Set the generator main circuit breaker to ON or default setting). After starting, the transfer switch should CLOSED. The generator now powers all LOAD connect load circuits to the standby side after a five (5) circuits. Check generator operation under load as second warm-up delay.

  • Page 22: Preparing For Maintenance

    Operation Testing The SACM To turn the generator back ON: 1. Install 7.5A fuse in controller. A “Test” pushbutton is provided on top of the SACM to test the operation of the load shed functions. The test 2. Confirm generator MLCB (generator pushbutton will work when the ATS is in the utility or the...

  • Page 23: Section 5: Drawings And Diagrams

    Drawings and Diagrams Section 5: Drawings and Diagrams Installation Drawing No. 10000027062 GROUP G INSTALLATION DRAWING REVISION: A INSTALL 100A-200A SER CUL SACM DATE: 01/11/18 DRAWING #: 10000027062 Automatic Transfer Switch Owner’s Manual...

  • Page 24: Interconnection Drawing

    Drawings and Diagrams Interconnection Drawing No. 10000027057—page 1 of 2 GROUP G INTERCONNECTION DIAGRAM REVISION: A ID 100A-200A CUL SACM DATE: 01/11/18 DRAWING #: 10000027057 Automatic Transfer Switch Owner’s Manual...

  • Page 25: 10000027057

    Drawings and Diagrams No. 10000027057—page 2 of 2 GROUP G INTERCONNECTION DIAGRAM REVISION: A ID 100A-200A CUL SACM DATE: 01/11/18 DRAWING #: 10000027057 Automatic Transfer Switch Owner’s Manual...
  • Page 26 Drawings and Diagrams This page intentionally left blank. Automatic Transfer Switch Owner’s Manual...
  • Page 28 Waukesha, WI 53187 The Honeywell trademark is used under license from Honeywell International Inc. 1-855-GEN-INFO Honeywell International Inc. makes no representation or warranties with respect to this product. This product is manufactured by Generac Power Systems, Inc., Waukesha, WI 53189, USA. honeywellgenerators.com...

This manual is also suitable for:

Rxsw200a3culh

Table of Contents