Preparing And Using The Touch Pen; Inserting The Battery; Using The Touch Pen; Eraser - Sharp PN-L601B Operation Manual

Preparing and Using the Touch Pen

Inserting the battery

1. Rotate the battery cap and remove it, and then pull out the
cover.
2. Insert the supplied battery (LR-03 ("AAA" size)) in the
orientation shown, and attach the cover and battery cap.
TIPS
• If the battery indicator does not illuminate when Function
Button 1 or Function Button 2 is pressed, the battery is
exhausted. Replace the battery with a new commercially
available battery.
• The supplied battery (LR-03 ("AAA" size)) may be
exhausted in a short time, depending on how it was stored.
• If the touch pen will not be used for an extended time,
remove the battery from the touch pen.
• For the battery, use an alkaline battery.

Using the touch pen

The touch pen can be used to perform the same operations
as a mouse.
When the touch panel is touched with the pen, the input mode
changes to pen mode. When touched with your finger, the
input mode changes to handwriting mode. The input mode is
set by default to change automatically.
Caution
• Do not use the touch pen for any purpose other than touch
panel operation.
• Do not press hard on the pen tip.
• Do not cover the ultrasonic transmitter with your hand or
finger.
• Operation will not take place correctly if there is an obstacle
between the infrared transmitter/receiver and the touch pen
or your finger. Operation will not take place correctly if your
fingers or your sleeve is near the screen.
• If the touch pen is held too flat against the screen, the
touch position may not be correctly detected.
• Do not store with the pen tip or function button pressed.
The battery will be exhausted.
• Do not use near a device that emits ultrasonic waves. The
touch pen uses ultrasonic waves and may not operate
correctly.
• If two touch panels are used in close proximity to each
other, use handwriting mode. The touch pens will interfere
with each other and will not operate correctly.
• If there is dirt or foreign matter on the tip of the touch pen,
remove it. Foreign matter may damage the screen.
Pen tip
Function Button 1
Battery cap
Touching with the pen tip or your finger...
Same as clicking the left mouse button.
Touching twice quickly is the same as double-clicking the left
mouse button.
Pressing Function Button 1...
Same as clicking the right mouse button.
The battery indicator illuminates.
Pressing Function Button 2...
Causes the function set in the Pen Software to operate in the
Pen Software.
The battery indicator illuminates.
Moving the pen tip or your finger with it touching the
screen...
Same as dragging.
TIPS
• The touch panel input mode, the actions of the function
buttons, and other settings related to touch panel operation
can be changed in the touch panel driver. For details, see
the Touch Panel Driver Operation Manual.
• When double clicking with your finger, make sure your
finger leaves the screen sufficiently after the first touch. If
there is not sufficient distance between your finger and the
screen, double clicking will not take place.
• For the procedures for using the touch pen in the Pen
Software, see the Pen Software Operation Manual.
• Use Function Button 1 and Function Button 2 near the front
of the screen. If too far away, operation will not be possible.
• Press Function Button 1 and Function Button 2 slowly
and firmly. If pressed too quickly, the action will not be
recognized.
• If the pen tip becomes worn or damaged, replace it. Pull
out the old pen tip and insert a new pen tip.

Eraser

The eraser is used with the Pen Software. For the procedure
for using the eraser, refer to the Pen Software Operation
Manual.
Caution
• When using the eraser, gently bring the cloth side into
contact with the screen. Touching the screen with one of
the non-cloth sides will damage the screen.
• If there is any dirt or foreign matter on the surface that
contacts the screen, remove it. Foreign matter may damage
the screen.
Function Button 2
Ultrasonic transmitter
Battery indicator
17
E