Lorex VANTAGE CVC7576 Series Quick Start Manual

Cable Extension Options
Extend the cable run for your camera up to 300ft or more
depending on the cable type used. See table below:
Max. Cable
Option Cable Type
Run Distance
1 Regular BNC 180ft / 55m
(supplied with
camera)
2 'RG59' or 'Coax' 300ft / 92m
or ' Coaxial' BNC
(sold separately)
3 Lorex Universal 300ft / 92m
Cable
(sold separately)
Notes:
1. For optimal performance, consider using option 2 or 3. Preference for using
the same cable type for the entire distance.
2. Cable run recommendation based on typical camera power consumption
(up to 500mA). For specialty cameras with higher current consumption,
maximum cable run may be reduced. Consider providing power to the
camera at the camera side rather then at the end of the extension cable.
3. Indicators that your cable run may be too long:
• Video is permanently Black & White (even during day time)
• Video is distorted
Troubleshooting
Problem Solution
No Picture/Signal • Ensure your TV is on the correct input channel.
Common terms of an input channel: INPUT, AV
CHANNEL, LINE1, LINE2, AUX.
• If your camera is connected to a VCR/DVR,
ensure it is properly connected to your TV/
Monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged in.
Picture is too bright
• Ensure your camera isn't pointed directly at a
source of light (e.g sun or spot light).
• Slide the sunshade (bullet cameras featuring
adjustable sunshades only) forward to block
excess light.
• Move your camera to a different location.
Picture is too dark • If using during the day, the camera may not be
getting enough light. Slide the sunshade (bullet
cameras featuring adjustable sunshades only)
backwards to let in more light.
• Check the brightness and contrast settings of the
device your camera connects to (TV/Monitor/
DVR).
Night Vision is not • The night vision activates when light levels drop.
working The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust, spiderwebs.
Clean the lens with a soft, clean cloth.
• Make sure that the cable run is within the
limitations specified in the section ' Cable
Extension Options'
Bright spot in video • Night vision reflects when pointing a camera to
when viewing cam-
a window. Move the camera to a different
era at night location.
BNC connection • Use a BNC to RCA adapter at the end of the
does not connect to extension cable.
my TV
Camera Specifications
Image Sensor
Video Format
Max. # of
Effective Pixels
Extensions
Resolution
3
Scan System
5
Sync System
S/N Ratio
3
Iris
AES Shutter Speed
Min. Illumination
Video Output
Lens / Lens Type
FOV (Diagonal)
Termination
IR LED Qty / Type
Night Vision Range*
Power Requirement
Power Consumption
Operating Temp. Range
Operating Humidity Range
Environmental Rating**
Weight (including stand)
*IR Illumination range under ideal conditions. Objects at or beyond this range may be partially or
completely obscured, depending on the camera application.
**Not intended for submersion in water. Installation in a sheltered location recommended.
Product Information
User Manuals
Quick Start Guides
Copyright © 2011 Lorex Technologies Inc.
As our products are subject to continuous improvement, Lorex reserves the right to modify product design,
specifications and prices, without notice and without incurring any obligation. E&OE
1/3" Color Image Sensor
NTSC
H: 720 V: 480
600+ TV Lines
2:1 Interlace
Internal
48dB (AGC Off)
AES
1/60 ~ 1/25,000 Sec.
0.1 Lux without IR LED
0 Lux with IR LED
Composite 1.0Vpp @75 ohm
3.6mm F2.0 / Fixed
78°
BNC Type
18 pieces / 850nm
85ft / 26m
12V DC ±10%
Max. 240mA (w/IR)
–22° ~ 122°F / –30° ~ 50°C
< 90% RH
IP66
0.6lbs / 0.3kg
4.2"/
2.6"/
107mm
66mm
5.2"/
132mm
www.lorextechnology.com
Specification Sheets
Software Upgrades
Firmware Upgrades
SUPER RESOLUTION WEATHERPROOF
NIGHT VISION SECURITY CAMERA
QUICK START GUIDE
English Version 3.0
CVC7576 Series
WWW.LOREXTECHNOLOGY.COM