Toyota Highlander Hybryd Owner's Manual

Table of Contents

Quick Links

Download this manual

Table of Contents

Summary of Contents for Toyota Highlander Hybryd

Page 3 Search by illustration Pictorial index Make sure to read through them For safety (Main topics: Child seat, theft deterrent system) and security Vehicle status Reading driving-related information information and (Main topics: Meters, multi-information display) indicators Opening and closing the doors and windows, adjustment before driving Before driving (Main topics: Keys, doors, seats, power windows)
Page 4 TABLE OF CONTENTS For your information ......Reading this manual......Before driving How to search ....... Pictorial index ........ 3-1. Key information Keys........106 For safety and security 3-2. Opening, closing and locking the doors 1-1. For safe use Side doors......109 Before driving......
Page 5 Dynamic radar cruise control Compass......298 ..........228 Cruise control......237 Maintenance and care BSM (Blind Spot Monitor) ...239 Toyota parking assist-sensor 6-1. Maintenance and care ..........244 Cleaning and protecting the RCTA (Rear Cross Traffic Alert) vehicle exterior ....302 function ......251 Cleaning and protecting the...
Page 6 TABLE OF CONTENTS If the hybrid system will not start 6-3. Do-it-yourself maintenance ..........392 Do-it-yourself service precau- tions ........315 If you lose your keys ...394 Hood ........317 If the fuel filler door cannot be opened......394 Positioning a floor jack..318 If the electronic key does not Engine compartment...319 operate properly...
Page 7 Toyota vehicles are currently avail- able in the market. Using these  Seat belt pretensioner system spare parts and accessories which Be sure to check with your Toyota are not genuine Toyota products dealer for precautionary measures may adversely affect the safety of...
Page 8 Unwanted noise may occur in the • For use by Toyota in a lawsuit reception of the radio frequency • For research purposes where the transmitter (RF-transmitter).
Page 9 • For use by Toyota in a lawsuit • How fast the vehicle was However, if necessary, Toyota may: traveling. • Use the data for research on vehicle...
Page 10 WARNING ■ General precautions while driv- Driving under the influence: Never drive your vehicle when under the influence of alcohol or drugs that have impaired your ability to operate your vehicle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Page 11 Reading this manual Symbols Meanings Indicates the action (pushing, turning, etc.) Explains symbols used in this used to operate manual. switches and other devices. Symbols in this manual Indicates the outcome of an operation (e.g. a Symbols Meanings lid opens). WARNING: Explains something that, if not obeyed,...
Page 12 ■ How to search Searching by title  Table of contents: P.2 ■ Searching by name  Alphabetical index: P.433 ■ Searching by installation posi- tion  Pictorial index: P.11 ■ Searching by symptom or sound  What to do if... (Troubleshoot- ing): P.430 HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 13 Pictorial index Pictorial index ■Exterior Side doors ..................P.109 Locking/unlocking ................P.109 Opening/closing the side windows...........P.141 Locking/unlocking by using the mechanical key ......P.395 Warning lights/warning messages ...........P.369, 377 Back door ..................P.113 Opening from inside the cabin ............P.116 Opening from outside............... P.116 Warning lights/warning messages ...........P.369, 377 Outside rear view mirrors .............P.138 Adjusting the mirror angle ..............P.138...
Page 14 Pictorial index Precautions for car wash ..............P.303 Fuel filler door ................P.185 Refueling method................P.185 Fuel type/fuel tank capacity ............. P.411 Tires ....................P.328 Tire size/inflation pressure ............P.328, 415 Winter tires/tire chains ..............P.266 Checking/rotation/tire pressure warning system ......P.328 Coping with flat tires.................P.381 Hood....................P.317 Opening ...................P.317 Engine oil ..................
Page 15 Pictorial index ■Instrument panel Power switch ..................P.160 Starting the hybrid system/changing the modes ......P.160 Emergency stop of the hybrid system..........P.360 When the hybrid system will not start ..........P.392 Warning messages ................P.377 Shift lever..................P.166 Changing the shift position...............P.166 Precautions for towing ..............P.363 When the shift lever does not move..........P.167 Meters ....................P.69 Reading the meters/adjusting the instrument panel light .....P.69, 71...
Page 16 Pictorial index When the warning messages are displayed ........P.377 Turn signal lever ................P.169 Headlight switch ................P.175 Headlights/front position lights/tail lights/license plate lights/daytime running lights....................P.175 Front fog lights/rear fog lights ............P.180 Windshield wiper and washer switch ........P.181, 184 Usage..................P.181, 184 Adding washer fluid................P.323 Warning messages ................P.377 Emergency flasher switch.............P.360 Hood lock release lever..............P.317...
Page 17 Pictorial index ■Switches Driving position memory switches ..........P.131 Window lock switch...............P.143 Power window switches..............P.141 Door lock switches ................ P.111 Outside rear view mirror switches ..........P.138 “ODO TRIP” switch................P.71 Instrument panel light control switches ........P.71 Automatic High Beam switch .............P.178 Camera switch Power back door switch .............
Page 18 Pictorial index Meter control switches ..............P.73, 81 Vehicle-to-vehicle distance switch ........P.223, 232 Cruise control switch Dynamic radar cruise control with full-speed range ......P.218 Dynamic radar cruise control ............P.228 Cruise control ................P.237 Audio remote control switches LTA (Lane Tracing Assist) switch ..........P.200 LDA(Lane Departure Alert with steering control) switch ..P.210...
Page 19 Pictorial index USB port USB charging ports ...............P.294 Power outlet ...................P.296 Brake hold switch ................P.172 Parking brake switch ..............P.169 Applying/releasing................P.169 Precautions against winter season ..........P.266 Warning buzzer/light/message..........P.369, 377 Trail Mode switch ................P.257 EV drive mode switch..............P.164 VSC OFF switch ................P.260 Driving mode select switch............P.256 : Refer to “Navigation and Multimedia System Owner’s Manual”...
Page 20 Pictorial index ■Interior SRS airbags..................P.29 Floor mats..................P.22 Front seats..................P.125 Rear seats..................P.126 Head restraints................P.133 Seat belts ..................P.25 Console box ...................P.287 Inside lock buttons ................ P.111 Cup holders ..................P.287 Assist grips ..................P.295 *1, 2 Rear seat entertainment system : If equipped : Refer to “Navigation and Multimedia System Owner’s Manual”. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 21 Pictorial index ■Ceiling Auxiliary box ..................P.288 Conversation mirror ..............P.297 Interior light .................P.284 Personal lights ................P.284 Moon roof switches ..............P.144 Panoramic moon roof switches ..........P.147 Vanity mirrors.................P.297 Sun visors ..................P.296 Inside rear view mirror ..............P.137 : The illustration shows the front, but they are also equipped in the rear. : If equipped : NEVER use a rearward facing child restraint on a seat protected by an ACTIVE AIRBAG in front of it, DEATH or SERIOUS INJURY to the CHILD can occur.
Page 22 Pictorial index HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 23 For safety and security 1-1. For safe use Before driving ..... For safe driving ....Seat belts......SRS airbags ....... Exhaust gas precautions ..1-2. Child safety Riding with children .... Child restraint systems ..1-3. Hybrid system Hybrid system features..Hybrid system precautions .........
Page 24 ● Insert the retaining hooks (clips) other models or different model year vehicles, even if they are into the floor mat eyelets. Toyota Genuine floor mats. Only use floor mats designed for ● the driver’s seat. ● Always install the floor mat securely using the retaining hooks (clips) provided.
Page 25 1-1. For safe use For safe driving WARNING With the hybrid system stopped and ● the shift lever in P, fully depress For safe driving, adjust the each pedal to the floor to make sure seat and mirror to an appropri- it does not interfere with the floor mat.
Page 26 1-1. For safe use ward clearly by adjusting the inside WARNING and outside rear view mirrors prop- Do not adjust the position of the ● erly. (P.137, 138) driver’s seat while driving. Doing so could cause the driver to lose con- trol of the vehicle.
Page 27 Toyota recommends that children ● with the rounding of the abdominal be seated in the rear seat and area.
Page 28 Seat belt regulations If seat belt regulations exist in the coun- Correct use of the seat belts try where you reside, please contact your Toyota dealer for seat belt replace- ment or installation. Fastening and releasing the seat belt  Extend the shoulder belt so that...
Page 29 1-1. For safe use To release the seat belt, press Push the seat belt shoulder anchor up. the release button Move the height adjuster up and down as needed until you hear a click. ■ When not using the rear seat belts Pass the outer seat belts through the seat belt hangers and secure the seat WARNING...
Page 30 WARNING ■ Seat belt pretensioners If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 31 1-1. For safe use SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
Page 32 1-1. For safe use Can help protect primarily the head of occupants in the outer seats ■ SRS airbag system components Front passenger airbag Front side airbags Curtain shield airbags Side impact sensors (rear) SRS warning light Driver airbag Side impact sensors (front door) Seat belt pretensioners and force limiters Driver’s knee airbag Front impact sensors...
Page 33 1-1. For safe use rails, may be hot for several minutes. from a direction perpendicular to the The airbag itself may also be hot. vehicle orientation at an approximate speed of 20 - 30 km/h [12 - 18 mph]). The windshield may crack. ●...
Page 34 In the following cases, the vehicle will ger compartment. require inspection and/or repair. Contact your Toyota dealer as soon as possible. ● Collision from the side to the vehicle body other than the passenger com- Any of the SRS airbags have been ●...
Page 35 1-1. For safe use ● The pad section of the steering wheel, The driver and all passengers in the ● dashboard near the front passenger vehicle must wear their seat belts airbag or lower portion of the instru- properly. ment panel is scratched, cracked, or The SRS airbags are supplemental otherwise damaged.
Page 36 Do not allow anyone to kneel on the ● properly secured using a child passenger seat toward the door or restraint system. Toyota strongly put their head or hands outside the recommends that all infants and vehicle. children be placed in the rear seats of the vehicle and properly restrained.
Page 37 All of these items could become pro- form any of the following modifica- tions without consulting your Toyota jectiles and may cause death or serious injury, should the SRS cur- dealer. The SRS airbags may mal- tain shield airbags deploy.
Page 38 If you smell exhaust gases in the ● vehicle even when the back door is closed, open the windows and have the vehicle inspected at your Toyota dealer as soon as possible. ■ When parking If the vehicle is in a poorly venti- ●...
Page 39 1-2. Child safety Riding with children 1-2.Child safety WARNING ■ When children are in the vehicle Never leave children unattended in Observe the following precau- the vehicle, and never allow children tions when children are in the to have or use the key. vehicle.
Page 40 • Fixed with a seat belt: P.47 this manual. • Fixed with an ISOFIX lower ● Toyota strongly urges the use of a anchorage: P.49 proper child restraint system that • Using a top tether anchorage: conforms to the weight and size of P.50...
Page 41 1-2. Child safety When using a child restraint WARNING system Holding a child in your or someone ● else’s arms is not a substitute for a ■ child restraint system. In an acci- When installing a child dent, the child can be crushed restraint system to a front pas- against the windshield or between senger seat...
Page 42 1-2. Child safety WARNING ■ When using a child restraint sys- Observe the following precautions. Failure to do so may result in death or serious injury. Never use a rear-facing child ● restraint system on the front pas- senger seat. The force of the rapid inflation of the front passenger airbag can cause death or serious injury to...
Page 43 1-2. Child safety WARNING ● Do not allow the child to lean WARNING his/her head or any part of his/her ● Only put a forward-facing child body against the door or the area of restraint system on the front seat the seat, front or rear pillars, or roof when unavoidable.
Page 44 1-2. Child safety ■ Before confirming the compat- WARNING ibility of each seating position Use child restraint system suitable ● with child restraint systems to the age and size of the child and install it to the rear seat. Checking the child restraint sys- tem standards.
Page 45 1-2. Child safety UN(ECE) R129 approval mark ■ Compatibility of each seating is indicated. position with child restraint Checking the category of the systems child restraint system. Check the approval mark of the child restraint system for which of the following categories the child restraint system is suitable.
Page 46 1-2. Child safety seatback angle until good contact is Suitable for “universal” category achieved. child restraint system fixed with the seat belt. Suitable for ISOFIX child restraint system. Includes a top tether anchorage point. Never use a rear-facing child restraint system on the front passenger seat.
Page 47 1-2. Child safety ISOFIX child restraint systems are divided into different “fixture”. The child restraint system can be used in the seating positions for “fixture” mentioned in the table above. For kind of “fixture” relation, confirm the following table. If your child restraint system has no kind of “fixture” (or if you cannot find information in the table below), please refer to the child restraint system “vehicle list”...
Page 48 1-2. Child safety  When installing a junior seat, if the child in your child restraint system is in a very upright posi- tion, adjust the seatback angle to the most comfortable position. And if the seat belt shoulder anchor is ahead of the child seat belt guide, move the seat cush- ion forward.
Page 49 1-2. Child safety Installation method Page ISOFIX lower anchor- P.49 ages attachment Top tether anchorage P.50 attachment If installing the child restraint Child restraint system fixed system to the front passenger with a seat belt seat is unavoidable, refer to P.39for the front passenger seat ■...
Page 50 If your child restraint system does not provide a locking clip, you can purchase the following item from your Toyota dealer: Locking clip for child restraint system If your child restraint system is (Part No. 73119-22010)
Page 51 1-2. Child safety gory (or the necessary information WARNING is not in the table), refer to the After securing a child restraint sys- ● “Vehicle List” provided by the child tem, never adjust the seat. restraint system maker for various When a junior seat (booster seat) is ●...
Page 52 1-2. Child safety for the second outboard seats: seatback. Use top tether anchorages when fixing the top strap. Top tether anchorages After installing the child restraint Top strap system, rock it back and forth to ■ Fixing the top strap to the top ensure that it is installed tether anchorages securely.
Page 53 1-2. Child safety NOTICE ■ Top tether anchorages When not in use, make certain to close the lid. If it remains open, the lid may be damaged. Hook Top strap WARNING ■ When installing a child restraint system Observe the following precautions. Failure to do so may result in death or serious injury.
Page 54 1-3. Hybrid system Hybrid system features 1-3.Hybrid system Your vehicle is a hybrid vehicle. It has characteristics different from conventional vehicles. Be sure you are closely familiar with the characteristics of your vehicle, and operate it with care. The hybrid system combines the use of a gasoline engine and an electric motor (traction motor) according to driving conditions, improving fuel efficiency and reducing exhaust emissions.
Page 55 (traction battery) becomes fully dis- charged and you are unable to start the The accelerator pedal is released ● hybrid system, contact your Toyota while driving with the shift lever in D or dealer. ■ The brake pedal is depressed while ●...
Page 56 Cooling fan sounds may be heard from the air intake vents under the rear seat. ■ Maintenance, repair, recycling, and disposal Contact your Toyota dealer regarding maintenance, repair, recycling and dis- posal. Do not dispose of the vehicle yourself. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 57 1-3. Hybrid system Hybrid system precautions Take care when handling the hybrid system, as it is a high voltage system (about 650 V at maximum) as well as contains parts that become extremely hot when the hybrid system is operating. Obey the warning labels attached to the vehicle.
Page 58 1-3. Hybrid system on a level surface. This value may vary Never try to open the service plug ● when the vehicle is on a slope. Add access hole located under the rear extra fuel when the vehicle is inclined.) seat.
Page 59 This may cause a fire. (P.363) by your Toyota dealer or a qualified service shop. If the hybrid battery is Carefully inspect the ground under ●...
Page 60 If the replacement is recommended. “READY” indicator does not come on, Refer to P.342for details on how to contact your Toyota dealer. clean the filters. Emergency shut off system When a certain level of impact is...
Page 61 1-4. Theft deterrent system Immobilizer system 1-4.Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type immobilizer system. The vehicle’s keys have ■ built-in transponder chips that Conditions that may cause the sys- tem to malfunction prevent the hybrid system ●...
Page 62 1-4. Theft deterrent system being on to flashing when the system is Alarm set. : If equipped The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: ...
Page 63 1-4. Theft deterrent system ■ Alarm-operated door lock In the following cases, depending on the situation, the door may automatically lock to prevent improper entry into the vehicle: When a person remaining in the vehi- ● cle unlocks the door and the alarm is activated.
Page 64 1-4. Theft deterrent system HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 65 Vehicle status information and indicators 2-1. Instrument cluster Warning lights and indicators ......... Gauges and meters .... Multi-information display (4.2-inch display) ....Multi-information display (7-inch display) ....Head-up display....Energy monitor/consumption screen....... HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 66 2-1. Instrument cluster Warning lights and indicators 2-1.Instrument cluster The warning lights and indicators on the instrument cluster, center panel and outside rear view mirrors inform the driver of the status of the vehicle’s various systems. Warning lights and indicators displayed on the instrument cluster For the purpose of explanation, the following illustrations display all warning lights and indicators illuminated.
Page 67 (P.370) (P.372) Charging system warning LTA indicator/LDA indicator light (P.370) (if equipped) (P.372) Low engine oil pressure (orange) Toyota parking assist-sensor warning light (P.370) *1, 3, 4 OFF indicator Malfunction indicator lamp equipped) (P.373) (flashes) (P.370) SRS warning light (P.370)
Page 68 Slip indicator (P.374) result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs. Parking brake indicator (P.374) (flashes)
Page 69 (P.160) come on, or turn off. Have the vehi- cle inspected by your Toyota dealer. “READY” indicator (P.160) : In order to confirm operation, the EV drive mode indicator BSM outside rear view mirror indica- (P.164)
Page 70 If this occurs, have the vehicle inspected by your Toyota dealer. : This light illuminates on the outside rear view mirrors. : When the outside temperature is approximately 3°C (37°F) or lower,...
Page 71 2-1. Instrument cluster Gauges and meters Meter display ■ Locations of gauges and meters 4.2-inch display  7-inch display  The units used on the meters may differ depending on the target region. Hybrid System Indicator Displays hybrid system output or regeneration level (P.70) Multi-information display Presents the driver with a variety of vehicle data (P.72, 81) HIGHLANDER HV_GE...
Page 72 2-1. Instrument cluster Displays warning messages in case of a malfunction (P.377) Clock (P.72) Speedometer Fuel gauge Displays the quantity of fuel remaining in the tank Odometer and trip meter display (P.71) Shift position display (P.166) Outside temperature Displays the outside temperature within the range of -40°C (-40°F) to 50°C (122°F). Low outside temperature indicator comes on when the ambient temperature is 3°C (37°F) or lower.
Page 73 When “--” or “E” is displayed, the sys- engine after it has cooled com- ● tem may be malfunctioning. Take your pletely. (P.403) vehicle to your Toyota dealer. ■ Liquid crystal display Odometer and trip meter Small spots or light spots may appear display on the display.
Page 74 2-1. Instrument cluster panel lights can be adjusted. Multi-information display (4.2-inch display) Display and menu icons ■ Display The multi-information display pre- sents the driver with a variety of driving-related information. Warning or suggestion/advice This image is for example only, and pop-up displays are also displayed may differ from the actual vehicle.
Page 75 2-1. Instrument cluster customizable items ■ Liquid crystal display Return to the previous screen Small spots or light spots may appear on the display. This phenomenon is Call sending/receiving and his- characteristic of liquid crystal displays, tory display and there is no problem continuing to use the display.
Page 76 2-1. Instrument cluster When only a small amount of fuel is fuel cannot be calculated. added to the tank, the display may not Refuel immediately. be updated. Current fuel economy When refueling, turn the power switch Displays the instantaneous current fuel off.
Page 77 2-1. Instrument cluster  ECO Accelerator Guidance ping. When the vehicle is stopped, an Eco score out of 100 points will be dis- played. Eco area Indicates that the vehicle is being Score result driven in an Eco-friendly manner. Eco start status Power area Eco cruise status Indicates that the Eco-friendly driving...
Page 78 2-1. Instrument cluster display) ■ The ECO Accelerator Guidance/Eco score will not operate when ■ Route guidance to destination dis- The ECO Accelerator Guidance/Eco play score will not operate in the following sit- When the route guidance to destination uations: display is enabled on the head-up dis- The Hybrid System Indicator is not ●...
Page 79 2-1. Instrument cluster Displays the size and direction of the driven since hybrid system start G-force applied to the vehicle via • “Total Time”: Displays the elapsed changes to the position of the ball on time since hybrid system start the display.
Page 80 Press to enable/disable the pressure warning system sensor ID pre-collision system. codes must be registered by a Toyota • PCS (Pre-Collision System) on/off dealer. For information regarding changing the registered ID code set, Select to enable/disable the pre-colli-...
Page 81 2-1. Instrument cluster contact your Toyota dealer. (P.335) • Display contents Select to display/not display the AWD • “Change Wheel” (register tire pres- sure warning system sensor ID control (if equipped) and energy moni- codes) tor. (P.77, 96) Select to register the ID codes of the •...
Page 82 2-1. Instrument cluster the headlight switch is in the the pop-up display is no longer dis- played. “AUTO” position, a suggestion message will be displayed asking if WARNING you wish to turn the headlights off. ■ Cautions during setting up the To turn the headlights off, select display “Yes”.
Page 83 2-1. Instrument cluster Multi-information display ■ Liquid crystal display (7-inch display) Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, Display and menu icons and there is no problem continuing to use the display.
Page 84 2-1. Instrument cluster customizable items Displays the driving range with remain- ing fuel. Return to the previous screen This distance is computed based on Call sending/receiving and his- your average fuel consumption. As a tory display result, the actual distance that can be driven may differ from that displayed.
Page 85 2-1. Instrument cluster Average fuel economy Displayed item (listed below) can be changed on the fuel economy type screen of . (P.86)  Total (after reset) Displays the average fuel consumption *1, 3 since the display was reset.  Tank (after refuel) ECO Accelerator Guidance Displays the average fuel consumption Eco score...
Page 86 2-1. Instrument cluster operation range for the current driving High conditions, such as starting off or cruis- • After the hybrid system is started, the ing. Eco score will not be displayed until This display changes according to situ- the vehicle speed exceeds approxi- ation, such as when starting off or cruis- mately 20 km/h (12 mph).
Page 87 2-1. Instrument cluster ● The Hybrid System Indicator is not play, it will not be displayed on the operating. multi-information display. (P.92) The vehicle is being driven using the ● cruise control (if equipped), dynamic Audio system-linked dis- radar cruise control (if equipped) or dynamic radar cruise control with play ( full-speed range (if equipped).
Page 88  PCS (Pre-Collision system) (if depending on if is pressed or equipped) (P.192) pressed and held. Follow the instruc- tions on the display.  Toyota parking assist-sensor (if ■ Setting items equipped) (P.244) LTA (Lane Tracing Assist) (if  BSM (Blind Spot Monitor) (if ...
Page 89 • “Volume” Press to enable/disable the pre-collision system. Select to set the volume of the buzzer which sounds when the Toyota parking • PCS (Pre-Collision System) on/off assist-sensor is operated. Select to enable/disable the pre-colli- sion system. RCTA (Rear Cross Traffic ...
Page 90  Multi-information display off pressure warning system sensor ID Displays a blank screen. codes must be registered by a Toyota  Default setting dealer. For information regarding changing the registered ID code set,...
Page 91 2-1. Instrument cluster tings to the default setting. NOTICE ■ Vehicle functions and settings ■ During setting up the display that can be changed To prevent 12-volt battery discharge, ensure that the hybrid system is oper- P.418 ating while setting up the display fea- tures.
Page 92 2-1. Instrument cluster ■ Suggestion to close the power windows (linked to windshield wiper operation) If the windshield wipers are oper- ated with a power window open, a suggestion message will be dis- played asking if you wish to close the power windows.
Page 93 2-1. Instrument cluster Head-up display : If equipped The head-up display is linked to the meters and navigation system (if equipped) and projects a variety of information in front of the driver, such as the current vehicle speed and route guidance to a set destination.
Page 94 2-1. Instrument cluster • Audio system operation status NOTICE ■ Head-up display will operate when The power switch is in ON. ■ To prevent damage to compo- nents ■ When using the head-up display Do not place any drinks near the ●...
Page 95 2-1. Instrument cluster following settings. ■ When the 12-volt battery is discon- nected  “HUD Brightness/Position” The customize settings of the head-up Select to adjust the brightness and ver- display will be reset. tical position of the head-up display. ■ Customization ...
Page 96 2-1. Instrument cluster display. (P.70) Hybrid System Indica- tor/Tachometer/Outside tem- Navigation system-linked perature display area (if equipped) ■ Hybrid System Indicator Displays the following navigation system linked items: (Refer to “Navigation and Multime- dia System Owner’s Manual”.) ■ Route guidance to destination Displayed when the navigation sys- tem is performing route guidance.
Page 97  Pop-up displays equipped) (P.192) When the driving assist system oper- ates, some of the information displayed  Toyota parking assist-sensor (if on the multi-information display will be equipped) (P.244) displayed on the head-up display as a  Drive-Start Control (P.153) pop-up display.
Page 98 2-1. Instrument cluster Audio system screen Energy monitor/con- sumption screen Multi-information display Meter control switches The state of the hybrid system can be viewed on the Energy monitor multi-information display and audio system display. ■ Audio system screen Press the “MENU” button. System components Select “Info”...
Page 99 2-1. Instrument cluster When the vehicle is powered by both the gasoline engine and the electric motor (traction motor) 2WD/AWD models AWD models only When the vehicle is powered by the gasoline engine 2WD/AWD models HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 100 2-1. Instrument cluster When the vehicle is charging the hybrid battery (traction battery) 2WD/AWD models AWD models only HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 101 2-1. Instrument cluster When there is no energy flow 2WD/AWD models These images are examples only, and Press of the meter may vary slightly from actual condi- control switch to select the tions. energy monitor display. Hybrid battery (traction battery) ...
Page 102 2-1. Instrument cluster When the vehicle is powered by the electric motor (traction motor) (Example: 7-inch display) 2WD/AWD models AWD models only When the vehicle is powered by both the gasoline engine and the electric motor (traction motor) (Example: 7-inch display) 2WD/AWD models AWD models only When the vehicle is powered by the gasoline engine (Example: 7-inch display)
Page 103 2-1. Instrument cluster When the vehicle is charging the hybrid battery (traction battery) (Example: 7-inch display) 2WD/AWD models AWD models only HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 104 2-1. Instrument cluster When there is no energy flow (Example: 7-inch display) 2WD/AWD models These images are examples only, and may vary slightly from actual conditions. Hybrid battery (traction battery) is displayed, select “Trip information”.  status (Example: 7-inch display) Resetting the consumption data Fuel consumption in the past 15 minutes...
Page 105 2-1. Instrument cluster into past averages and averages ■ Updating the history data attained since the power switch Update the latest fuel consumption by was last turned to ON. Use the dis- selecting “Update” to measure the cur- played average fuel consumption rent fuel consumption again.
Page 106 2-1. Instrument cluster HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 107 Before driving 3-1. Key information Keys........106 3-2. Opening, closing and locking the doors Side doors ......109 Back door ......113 Smart entry & start system ........121 3-3. Adjusting the seats Front seats......125 Rear seats ......126 Driving position memory ...131 Head restraints ....133 3-4.
Page 108 Toyota dealer to check if To reduce key battery depletion when ● an unknown electronic key (other than...
Page 109 Carrying the electronic key on your person : These settings must be customized Carry the electronic key 10 cm (3.9 at your Toyota dealer. in.) or more away from electric appli- : If equipped ances that are turned on. Radio waves emitted from electric appli- ances within 10 cm (3.9 in.) of the...
Page 110 3-1. Key information cannot be inserted in a lock cylinder, turn it over and re-attempt to insert it. After using the mechanical key, store it in the electronic key. Carry the mechan- ical key together with the electronic key. If the electronic key battery is depleted or the entry function does not operate properly, you will need the mechanical key.
Page 111 Unlocks all the doors Press and hold to open the windows *1, 2 and moon roof : This setting must be customized at your Toyota dealer. : If equipped ■ Switching the door unlock function Grip the front door handle to...
Page 112 3-2. Opening, closing and locking the doors moon roof are operating. Multi-information Unlocking function : If equipped display/Beep ■ Holding the Security feature driver’s door han- If a door is not opened within approxi- mately 30 seconds after the vehicle is dle unlocks only unlocked, the security feature automati- the driver’s door.
Page 113 3-2. Opening, closing and locking the doors ■ If the 12-volt battery is discharged ■ When using the wireless remote The doors cannot be locked and control and operating the power unlocked using the smart entry & start windows or moon roof (if system or wireless remote control.
Page 114 3-2. Opening, closing and locking the doors The driver’s door can be opened by Automatic door locking and pulling the inside handle even if the lock unlocking systems button is in the lock position. The following functions can be set ■...
Page 115 3-2. Opening, closing and locking the doors Back door Do not allow a child to open or ● close the back door. Doing so may cause the back door to The back door can be move unexpectedly, or cause the child’s hands, arms, head, or neck to locked/unlocked and be caught by the closing back door.
Page 116 Do steep incline. Make sure that the not attach any accessories other back door is secured before using than genuine Toyota parts to the the luggage compartment. back door. When closing the back door, take ●...
Page 117 Do not attach any accessories ● other than genuine Toyota parts to Be careful not to pull the back door the back door. sideways when using a handle.
Page 118 3-2. Opening, closing and locking the doors opposite direction. tion. Pressing the switch again will open the back door. ■ Opening/closing the back door ■ Opening/closing the back door using the power back door using the power back door switch on the instrument panel switch on the back door Press and hold the switch.
Page 119 3-2. Opening, closing and locking the doors ● When the power back door is open- ing/closing, if the power back door becomes obstructed, operation will stop. ■ Jam protection function Sensors are installed on the right and left sides of the power back door. When the door is automatically closing and the sensors are pushed due to an object being clamped, etc., the jam protection...
Page 120 3-2. Opening, closing and locking the doors tion function, etc., while the back door Check the safety of the surrounding ● is automatically closing after a door area to make sure there are no reserve lock operation is performed, obstacles or anything that could the door reserve lock function is cause any of your belongings to get canceled and all the doors will unlock.
Page 121 Do not attach any accessories ● operate, causing a malfunction, or other than genuine Toyota parts to the back door may suddenly shut the back door. again after being opened, causing someone’s hands, arms, head or Do not place your hand on the spin- ●...
Page 122 3-2. Opening, closing and locking the doors Press and hold the power back open to the last position set using the power back door switch on the back door switch on the back door for door or on the multi-information display. approximately 2 seconds.
Page 123 3-2. Opening, closing and locking the doors ■ Smart entry & start sys- Effective range (areas within which the electronic key is detected) The following operations can be performed simply by carry- ing the electronic key on your person, for example in your pocket.
Page 124 3-2. Opening, closing and locking the doors While the battery-saving mode is set, Correction Situation the smart entry & start system cannot be procedure used. To cancel the function, press any of the electronic key buttons. The power switch was turned to ACC while the Turn the driver’s door was open...
Page 125 3-2. Opening, closing and locking the doors • Personal computers or personal digi- car wash when the electronic key is tal assistants (PDAs) within the effective range. (The doors • Digital audio players will automatically be locked after • Portable game systems approximately 30 seconds if the doors are not opened and closed.) If window tint with a metallic content or...
Page 126 If the hybrid system cannot be started medical devices. using the smart entry & start system, refer to P.396. Ask your Toyota dealer for details on disabling the entry function. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 127 3-3. Adjusting the seats Vertical height adjustment Front seats 3-3.Adjusting the seats switch (driver’s side only) Lumbar support adjustment Adjustment procedure switch (driver’s side only) Manual seat  ■ When adjusting the seat Take care when adjusting the seat so that the head restraint does not touch the ceiling.
Page 128 3-3. Adjusting the seats Rear seats WARNING Manual seat only: After adjusting ● the seat, make sure that the seat is The seat position and seatback locked in position. angle can be adjusted, and the seatback can be folded by operating a seatback angle adjustment lever.
Page 129 3-3. Adjusting the seats Adjustment procedure WARNING ■ When folding the rear seatbacks ■ Second seats down Observe the following precautions. Failure to do so may result in death or serious injury. Do not fold the seatbacks down ● while driving. Stop the vehicle on level ground, ●...
Page 130 3-3. Adjusting the seats Stow the second seat belt buck- Moving a second seat for les. third seat access ■ When entering/exiting the vehicle Pull the seatback angle adjustment lever to tilt the seatback forward and then slide the seat for- ward.
Page 131 3-3. Adjusting the seats rately. ■ Returning the second seats Lift up the seatbacks until they lock. Remove the secured seat belts from the seat belt hangers before using them. Pull the seatback folding lever to unlock the seatback. The Folding down the third seats seatback will be folded down.
Page 132 3-3. Adjusting the seats being damaged. until they lock. After using either strap, use the velcro on the strap to attach it to the seatback. ■ Folding down the third seats While pulling the the seatback Returning the head restraints. angle adjustment lever, fold down the seatbacks.
Page 133 3-3. Adjusting the seats will be overwritten. Driving position mem- : If equipped This feature automatically adjusts the driver’s seat, out- side rear view mirrors and head-up display to suit your preferences. Two different driving positions ■ Seat positions that can be memo- can be recorded into memory.
Page 134 3-3. Adjusting the seats Press one of the buttons for the If 2 or more keys are in the vehicle, the driving position cannot be recorded driving position you want to properly. recall until the buzzer sounds. Check that the shift lever is in P. Turn the power switch to ON.
Page 135 3-3. Adjusting the seats ■ Recall procedure Head restraints Make sure that the doors are locked before recalling the driving Head restraints are provided position. Carry the electronic key for all seats. that has been registered to the driv- ing position, and then unlock and WARNING open the driver’s door using the ■...
Page 136 3-3. Adjusting the seats seat height or angle. (P.125, 126) ■ Second seats Front seats  Pull the head restraints up. Second seats  Down Push the head restraint down while pressing the lock release button ■ Adjusting the height of the head restraints Installing the head restraints Align the head restraint with the...
Page 137 3-3. Adjusting the seats Second seats  HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 138 3-4. Adjusting the steering wheel and mirrors Steering wheel 3-4.Adjusting the steering wheel and mirrors ■ After adjusting the steering wheel Make sure that the steering wheel is Adjustment procedure securely locked. Otherwise, the steering wheel may Hold the steering wheel and move suddenly, possibly causing an accident, and resulting in death or push the lever down.
Page 139 3-4. Adjusting the steering wheel and mirrors Inside rear view mirror The rear view mirror’s position can be adjusted to enable suf- ficient confirmation of the rear view. Adjusting the height of rear Normal position view mirror Anti-glare position The height of the rear view mirror Auto anti-glare inside rear view can be adjusted to suit your driving ...
Page 140 3-4. Adjusting the steering wheel and mirrors Outside rear view mir- ■ To prevent sensor error (vehicles rors with auto anti-glare inside rear view mirror) To ensure that the sensors operate The rear view mirror’s position properly, do not touch or cover them. can be adjusted to enable suf- ficient confirmation of the rear view.
Page 141 3-4. Adjusting the steering wheel and mirrors To adjust the mirror, operate the angle at a desired position with the shift lever in R. switch. The adjusted angle will be memorized and the mirror will automatically tilt to the memorized angle whenever the shift lever is shifted to R from next time.
Page 142 3-4. Adjusting the steering wheel and mirrors ■ Using automatic mode in cold weather When automatic mode is used in cold weather, the door mirror could freeze up and automatic stowing and return may not be possible. In this case, remove any ice and snow from the door mirror, then either operate the mirror using manual mode or move the mirror by...
Page 143 3-5. Opening, closing the windows and moon roof ■ Power windows Catch protection function 3-5.Opening, closing the windows and moon roof If an object becomes caught between the door and window while the window is opening, window movement is Opening and closing the stopped.
Page 144 If the window reverses and cannot be It is possible for children and other fully closed or opened, have the vehicle passengers to have body parts inspected by your Toyota dealer. caught in the power window. Also, when riding with a child, it is recom- ■...
Page 145 3-5. Opening, closing the windows and moon roof WARNING ■ Jam protection function Never use any part of your body to ● intentionally activate the jam pro- tection function. ● The jam protection function may not work if something gets jammed just before the window is fully closed.
Page 146 ■ Tilting up and down trol. (P.109) : These settings must be customized at your Toyota dealer. ■ When the moon roof does not close normally Perform the following procedure: If the moon roof closes but then ●...
Page 147 If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 148 3-5. Opening, closing the windows and moon roof The jam protection function may not ● WARNING work if something gets caught just Check to make sure that all passen- ● before the moon roof is fully closed. gers do not have any part of their Also, the jam protection function is body in a position where it could be not designed to operate while the...
Page 149 3-5. Opening, closing the windows and moon roof Panoramic moon roof : If equipped Use the overhead switches to operate the panoramic moon roof and electronic sunshade. Operating the panoramic Tilt down (press and hold) moon roof The panoramic moon roof can be ■...
Page 150 If an object is detected between the pan- above procedure correctly, have the oramic moon roof and the frame in the vehicle inspected by your Toyota dealer. following situations, travel is stopped and the panoramic moon roof opens ■...
Page 151 In order to prevent the above procedure correctly, have the accidental operation, especially by vehicle inspected by your Toyota dealer. a child, do not let a child operate ■ Panoramic moon roof open warn- the panoramic moon roof.
Page 152 3-5. Opening, closing the windows and moon roof WARNING ■ Jam protection function Never use any part of your body to ● intentionally activate the jam pro- tection function. ● The jam protection function may not work if something gets caught just before the panoramic moon roof or electronic sunshade is fully closed.
Page 153 Trailer towing ....159 Cruise control....237 4-2. Driving procedures BSM (Blind Spot Monitor) Power (ignition) switch..160 ........239 EV drive mode ....164 Toyota parking assist-sensor Hybrid transmission ..166 ........244 Turn signal lever ....169 RCTA (Rear Cross Traffic Alert) Parking brake ....169 function ......251...
Page 154 4-1. Before driving Set the parking brake (P.169), Driving the vehicle 4-1.Before driving and shift the shift lever to P (P.166). The following procedures Press the power switch to stop should be observed to ensure the hybrid system. safe driving: Lock the door, making sure that you have the electronic key on Driving procedure...
Page 155 ■ and drive at a stable speed within the Breaking in your new Toyota ECO Accelerator Guidance range. By To extend the life of the vehicle, observ- keeping the vehicle within the ECO...
Page 156 4-1. Before driving Do not drive the vehicle over or ● WARNING stop the vehicle near flammable Observe the following precautions. materials. Failure to do so may result in death or The exhaust system and exhaust serious injury. gases can be extremely hot. These hot parts may cause a fire if there is ■...
Page 157 (brake pad wear indica- make sure that the brakes are func- tors) tioning properly. Wet brake pads Have your Toyota dealer check and may prevent the brakes from func- replace the brake pads as soon as tioning properly. If the brakes on possible.
Page 158 4-1. Before driving Always apply the parking brake, ● WARNING shift the shift lever to P, stop the Avoid revving or racing the engine. ● hybrid system and lock the vehicle. Running the engine at high speed Do not leave the vehicle unat- while the vehicle is stopped may tended while the “READY”...
Page 159 When parking the vehicle Always set the parking brake and shift flooded, be sure to have your Toyota dealer check the following: the shift lever to P. Failure to do so may cause the vehicle to move or the Brake function ●...
Page 160 4-1. Before driving Cargo and luggage • On the luggage cover • On the instrument panel Take notice of the following • On the dashboard information about storage pre- Secure all items in the occupant ● cautions, cargo capacity and compartment.
Page 161 Toyota does not recommend of the moon roof or panoramic moon towing a trailer with your vehi- roof. cle. Toyota also does not rec- ommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc.
Page 162 ● The immobilizer system may not have been deactivated. (P.59) changes power switch modes. Contact your Toyota dealer. ● If a message related to start-up is Starting the hybrid system shown on the multi-information dis-...
Page 163 NOTICE does not come on even after performing the proper procedures for starting the ■ When starting the hybrid system vehicle, contact your Toyota dealer If the hybrid system becomes difficult immediately. to start, have your vehicle checked by ■...
Page 164 4-2. Driving procedures released. (The mode changes each Check the parking brake indicator is illuminated. time the switch is pressed.) Press the power switch. The hybrid system will stop, and the meter display will be extinguished. Release the brake pedal and check that “ACCESSORY”...
Page 165 4-2. Driving procedures function cannot entirely prevent 12-volt NOTICE battery discharge. Do not leave the vehi- cle with the power switch in ACC or ON ■ To prevent 12-volt battery dis- for long periods of time when the hybrid charge system is not operating.
Page 166 4-2. Driving procedures EV drive mode ■ Situations in which EV drive mode cannot be turned on It may not be possible to turn EV drive In EV drive mode, electric mode on in the following situations. If it power is supplied by the cannot be turned on, a buzzer will sound and a message will be shown on the hybrid battery (traction bat-...
Page 167 4-2. Driving procedures after flashing, and a message is dis- vehicle for a while before attempting to played on the multi-information display. turn on the EV drive mode again. The hybrid battery (traction battery) ● becomes low. WARNING The remaining battery level indicated ■...
Page 168 4-2. Driving procedures Hybrid transmission WARNING ■ When driving on slippery road surfaces Select the shift position Be careful of downshifting and sud- depending on your purpose den acceleration, as this could result and situation. in the vehicle skidding to the side or spinning.
Page 169 Have the vehicle inspected by your when the shift lock override button is Toyota dealer immediately. pressed and the shift lever is shifted out of P, the vehicle may suddenly The following steps may be used as an...
Page 170 S This may indicate a malfunction in the hybrid transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the hybrid transmission will operate in the same manner as when the shift lever is in D.)
Page 171 4-2. Driving procedures Turn signal lever Parking brake Operating instructions The parking brake can be set or released automatically or manually. In automatic mode, the parking brake can be set or released automatically according to the shift lever operation. Also, even in automatic mode, the parking brake can be set or released manually.
Page 172 4-2. Driving procedures Push the switch to release the turn on. parking brake Operate the shift lever with the • Operate the parking brake switch brake pedal depressed. while depressing the brake pedal. • Parking brake automatic release ■ Turns automatic mode off function (P.170) While the vehicle is stopped, press Make sure that the parking brake indi-...
Page 173 If the brake system warning light message does not disappear after oper- comes on ating the switch several times, the sys- P.369 tem may be malfunctioning. Have the vehicle inspected by your Toyota dealer ■ Usage in winter time immediately. P.266 ■...
Page 174 Have the vehicle inspected by your stop the vehicle. The system Toyota dealer immediately if this releases the brake when the occurs. accelerator pedal is depressed with the shift lever in D or S to allow smooth start off.
Page 175 Make sure that the parking brake indica- tor light goes off. (P.169) ■ When an inspection at your Toyota dealer is necessary When the brake hold standby indicator (green) does not illuminate even when HIGHLANDER HV_GE...
Page 176 4-2. Driving procedures NOTICE ■ When parking the vehicle The brake hold system is not designed for use when parking the vehicle for a long period of time. Turn- ing the power switch off while the sys- tem is holding the brake may release the brake, which would cause the vehicle to move.
Page 177 4-3. Operating the lights and wipers Headlight switch 4-3.Operating the lights and wipers ■ Daytime running light system To make your vehicle more visible to other drivers during daytime driving, the The headlights can be oper- daytime running lights turn on automati- ated manually or automatically.
Page 178 4-3. Operating the lights and wipers power switch is turned to ON, the 12-volt headlights on or off. battery-saving function will be disabled. When any of the following are per- formed, the 12-volt battery-saving func- Manual headlight leveling tion is canceled once and then dial reactivated.
Page 179 4-3. Operating the lights and wipers Occupancy and luggage load Occupancy and luggage Dial Dial conditions load conditions position position Occupants Luggage load Occupants Luggage load Driver, front All seats Full luggage passenger occupied loading and all pas- Full luggage Driver sengers in None...
Page 180 4-3. Operating the lights and wipers Push the lever away from you Automatic High Beam with the headlight switch in the : If equipped position. The Automatic High Beam The Automatic High Beam indicator will uses a camera sensor located come on when the system is operating.
Page 181 4-3. Operating the lights and wipers • When the vehicle is cut in front of by etc.) another vehicle • When the windshield is obscured by • When vehicles ahead cannot be fog, mist, ice, dirt, etc. detected due to repeated curves, road •...
Page 182 4-3. Operating the lights and wipers right-hand traffic in a left-hand traffic Fog light switch area, or vice versa The fog lights secure excellent Turning the high beams visibility in difficult driving on/off manually conditions, such as in rain and ■...
Page 183 4-3. Operating the lights and wipers Windshield wipers and Temporary operation washer Wiper intervals can be adjusted when intermittent operation is Operating the lever can switch selected. between automatic operation and manual operation, or can use the washer. NOTICE ■ When the windshield is dry Do not use the wipers, as they may damage the windshield.
Page 184 4-3. Operating the lights and wipers ume and vehicle speed. The sensor sensitivity can be adjusted when “AUTO” is selected. Washer/wiper dual oper- ation Pulling the lever operates the wipers and washer. The wipers will automatically operate a couple of times after the washer squirts. ■...
Page 185 ■ When a nozzle becomes blocked ■ In this case, contact your Toyota Front door opening linked wind- dealer. shield wiper stop function (vehicles Do not try to clear it with a pin or other with rain-sensing windshield wip- object.
Page 186 4-3. Operating the lights and wipers Rear windshield wiper Washer/wiper dual oper- and washer ation Pushing the lever operates the wiper and washer. NOTICE The wiper will automatically operate a ■ When the rear window is dry couple of times after the washer squirts. Do not use the wiper, as it may dam- The washer will automatically operate age the rear window.
Page 187 4-4. Refueling Opening the fuel tank 4-4.Refueling Always hold the grips on the fuel ● tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Perform the following steps to Wait until the sound cannot be open the fuel tank cap: heard before fully removing the...
Page 188 WARNING ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 189 4-5.Using the driving support systems WARNING ■ Toyota Safety Sense : If equipped The Toyota Safety Sense is designed to operate under the assumption that The Toyota Safety Sense con- the driver will drive safely, and is sists of the following drive...
Page 190 ● sensor sensor must be recalibrated. Con- Observe the following precautions. tact your Toyota dealer for details. Otherwise, the radar sensor may not • When the radar sensor or front operate properly, possibly leading to grille are removed and installed, or...
Page 191 Contact your Toyota dealer for remove the fog, condensation, or details.  ice. ( P.273)
Page 192 In the following situations, perform the actions specified in the table. When the nor- mal operating conditions are detected, the message will disappear and the system will become operational. If the message does not disappear, contact your Toyota dealer. Situation Actions...
Page 193 If the message does not disappear, contact your Toyota dealer. • When the temperature around the radar sensor is outside of the operational range, such as when the vehicle is in the sun or in an extremely cold environment •...
Page 194 4-5. Using the driving support systems PCS (Pre-Collision Sys- The pre-collision system can be tem) disabled/enabled and the warn- ing timing can be changed. : If equipped (P.195) The pre-collision system uses a radar sensor and front cam- era to detect objects (P.192) in front of the vehicle.
Page 195 4-5. Using the driving support systems countries and areas of each region may be different. Contact your Toyota dealer for details. System functions WARNING ■ Limitations of the pre-collision ■ Pre-collision warning system When the system determines that The driver is solely responsible for ●...
Page 196 4-5. Using the driving support systems When your vehicle is towing ● WARNING another vehicle ■ Pre-collision braking When transporting the vehicle via ● When the pre-collision braking ● truck, boat, train or similar means of function is operating, a large transportation amount of braking force will be applied.
Page 197 4-5. Using the driving support systems can be changed on (P.77, 86) Changing settings of the of the multi-information display. pre-collision system The warning timing setting is retained ■ Enabling/disabling the pre-col- when the power switch is turned OFF. lision system However, if the pre-collision system is The pre-collision system can be disabled and re-enabled, the operation...
Page 198 4-5. Using the driving support systems Relative speed between Detectable objects Vehicle speed your vehicle and object Approx. 10 to 180 km/h (7 Approx. 10 to 180 km/h (7 Vehicles to 110 mph) to 110 mph) Approx. 10 to 80 km/h (7 to Approx.
Page 199 4-5. Using the driving support systems Region B • When there is a detectable object or  other object by the roadside at the entrance of a curve ■ Cancelation of the pre-collision braking • When there are patterns or paint in If either of the following occur while the front of your vehicle that may be mis- pre-collision braking function is operat-...
Page 200 4-5. Using the driving support systems hole cover, steel plate, etc.), steps, or • If a detectable object makes an abrupt a protrusion in front of your vehicle maneuver (such as sudden swerving, • When passing under an object (road acceleration or deceleration) sign, billboard, etc.) •...
Page 201 4-5. Using the driving support systems such as at dawn or dusk, or while at night or in a tunnel, making a detecta- ble object appear to be nearly the same color as its surroundings • When driving in a place where the sur- rounding brightness changes sud- denly, such as at the entrance or exit of a tunnel...
Page 202 4-5. Using the driving support systems countries/areas that detection of bicy- LTA (Lane Tracing clists is not possible (P.192) Assist) : Applicable to vehicles designed for countries/areas that detection of : If equipped pedestrians and/or bicyclists is possi- When driving on highways and ble (P.192) freeways with white (yellow) ■...
Page 203 Do not modify the suspension etc. If ing operations and pay careful ● attention may lead to an accident, the suspension etc. needs to be replaced, contact your Toyota resulting in death or serious injury. dealer. When not using the LTA system, ●...
Page 204 4-5. Using the driving support systems Objects or patterns that could be ● WARNING mistaken for white (yellow) lines are When the follow-up cruising dis- ● present on the side of the road  play is displayed ( P.206) and the (guardrails, reflective poles, etc.).
Page 205 4-5. Using the driving support systems The vehicle is extremely tilted due ● WARNING to carrying heavy luggage or having The vehicle is driven in an area ● improper tire pressure. without white (yellow) lines, such as The distance to the preceding vehi- ●...
Page 206 4-5. Using the driving support systems the lane. displayed on the multi-information dis- play and the function is temporarily Vehicle with BSM: When the system canceled. determines that the vehicle might depart from its lane and that the possi- Vehicle with BSM: When the system bility of a collision with an overtaking determines that the vehicle might vehicle in the adjacent lane is high, the...
Page 207 4-5. Using the driving support systems canceled. ■ Lane centering function This function is linked with dynamic Turning LTA system on radar cruise control with full-speed range and provides the required Press the LTA switch to turn the assistance by operating the steer- LTA system on.
Page 208 4-5. Using the driving support systems display is switched to the driving assist system information display. Indicates that steering wheel assis- tance of the steering assist function or lane centering function is operating. Both outer sides of the lane are dis- played: Indicates that steering wheel assist of the lane centering function is operating.
Page 209 4-5. Using the driving support systems Inside of displayed lines is black km/h (32 mph) or more.  • System recognizes white (yellow) lane lines or a course . (When a white [yellow] line or course is recognized on only one side, the system will oper- ate only for the recognized side.) •...
Page 210 4-5. Using the driving support systems “ON”. (P.77, 86) ● If the operation conditions (P.207) • Vehicle speed is approximately 50 are no longer met while the lane cen- km/h (32 mph) or more. tering function is operating, the buzzer •...
Page 211 The system may not be operating prop- Depending on the vehicle condition and erly. Have the vehicle inspected by your road conditions, the warning may not Toyota dealer. operate. Also, if the system determines “LTA Unavailable” ● that the vehicle is driving around a...
Page 212 4-5. Using the driving support systems LDA (Lane Departure WARNING Alert with steering con- ■ Before using LDA system trol) Do not rely solely upon the LDA ● system. The LDA system does not automatically drive the vehicle or : If equipped reduce the amount of attention that must be paid to the area in front of When driving on highways and...
Page 213 Do not modify the suspension etc. If ● the suspension etc. needs to be replaced, contact your Toyota dealer. Do not install or place anything on ● the hood or grille. Also, do not install a grille guard (bull bars, kan- garoo bar, etc.).
Page 214 4-5. Using the driving support systems The vehicle is extremely tilted due ● WARNING to carrying heavy luggage or having The vehicle is driven in an area ● improper tire pressure. without white (yellow) lines, such as The distance to the preceding vehi- ●...
Page 215 4-5. Using the driving support systems bility of a collision with an overtaking determines that the vehicle might vehicle in the adjacent lane is high, the depart from its lane and that the possi- lane departure alert will operate even if bility of a collision with an overtaking the turn signals are operating.
Page 216 4-5. Using the driving support systems Indications on multi-infor- mation display LDA indicator The illumination condition of the indica- tor informs the driver of the system operation status. Illuminated in white: LDA system is operating. Turning LDA system on Illuminated in green: Steering wheel assistance of the steering assist func- Press the LDA switch to turn the tion is operating.
Page 217 4-5. Using the driving support systems Inside of displayed lines is white • Vehicle speed is approximately 50  km/h (32 mph) or more. • System recognizes white (yellow) lane lines or a course . (When a white [yel- low] line or course is recognized on only one side, the system will operate only for the recognized side.)
Page 218 4-5. Using the driving support systems m (9.8 ft.) or more. on the steering wheel when using this • No system malfunctions are detected. system, regardless of warnings. (P.217) ■ Temporary cancelation of functions When operation conditions are no longer met, a function may be temporar- ily canceled.
Page 219 ● “LDA Malfunction Visit Your Dealer” The system may not be operating prop- erly. Have the vehicle inspected by your Toyota dealer. ● “LDA Unavailable” The system is temporarily canceled due to a malfunction in a sensor other than the front camera.
Page 220 4-5. Using the driving support systems Indicators Dynamic radar cruise control with full-speed ■ Operation switches range : If equipped In vehicle-to-vehicle distance control mode, the vehicle auto- matically accelerates, deceler- ates and stops to match the speed changes of the preced- ing vehicle even if the acceler- Vehicle-to-vehicle distance ator pedal is not depressed.
Page 221 4-5. Using the driving support systems Assisting the driver to measure fol- ● WARNING lowing distance • Conditions under which the vehi- The dynamic radar cruise control with cle-to-vehicle distance control full-speed range is only intended to mode may not function correctly: help the driver in determining the fol- ...
Page 222 4-5. Using the driving support systems WARNING Roads where there are pedestrians, ● cyclists, etc. In heavy traffic ● ● On roads with sharp bends On winding roads ● ● On slippery roads, such as those covered with rain, ice or snow ●...
Page 223 4-5. Using the driving support systems Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver. Example of deceleration cruising and follow-up cruising When a preceding vehicle driving slower than the set speed appears When a vehicle is detected running ahead of you, the system automatically deceler- ates your vehicle.
Page 224 4-5. Using the driving support systems speed. Setting the vehicle speed (vehicle-to-vehicle distance control mode) Press the cruise control main switch to activate the cruise con- trol. Dynamic radar cruise control indicator will come on and a message will be dis- played on the multi-information display.
Page 225 4-5. Using the driving support systems increased or decreased as follows: Fine adjustment: By 1 km/h (0.6 mph) or 1 mph (1.6 km/h) each time the switch is pressed Large adjustment: Increases or decreases in 5 km/h (3.1 mph) or 5 mph (8 km/h) increments for as long as the switch is held...
Page 226 4-5. Using the driving support systems Distance Vehicle-to-vehicle dis- Canceling and resuming the options tance speed control Approximately 50 m (160 Long ft.) Approximately 40 m (130 Medium ft.) Approximately 30 m (100 Short ft.) Resuming follow-up cruis- ing when the vehicle has Pressing the cancel switch can- been stopped by system cels the speed control.
Page 227 4-5. Using the driving support systems Immediately after the switch is pressed, the dynamic radar cruise control indica- tor will come on. Afterwards, it switches to the cruise control indicator. Switching to constant speed control mode is only possible when operating the switch with the cruise control off.
Page 228 ■ Automatic cancelation of vehi- than the above, there may be a malfunc- cle-to-vehicle distance control tion in the system. Contact your Toyota mode dealer. Vehicle-to-vehicle distance control mode ■ is automatically canceled in the follow- Brake operation ing situations.
Page 229 4-5. Using the driving support systems ■ When the sensor may not be cor- rectly detecting the vehicle ahead In the case of the following and depend- ing on the conditions, operate the brake pedal when deceleration of the system is insufficient or operate the accelerator pedal when acceleration is required.
Page 230 4-5. Using the driving support systems ■ Dynamic radar cruise Operation switches control : If equipped In vehicle-to-vehicle distance control mode, the vehicle auto- matically accelerates and decelerates to match the speed changes of the preceding vehi- cle even if the accelerator Vehicle-to-vehicle distance pedal is not depressed.
Page 231 4-5. Using the driving support systems Assisting the driver to judge proper ● WARNING following distance Set the speed appropriately ● The dynamic radar cruise control depending on the speed limit, traffic determines whether the following dis- flow, road conditions, weather con- tance between the driver’s own vehi- ditions, etc.
Page 232 4-5. Using the driving support systems WARNING At entrances to freeways and high- ● ways When weather conditions are bad ● enough that they may prevent the sensors from detecting correctly (fog, snow, sandstorm, heavy rain, etc.) When there is rain, snow, etc. on ●...
Page 233 4-5. Using the driving support systems Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver. Example of deceleration cruising and follow-up cruising When a preceding vehicle driving slower than the set speed appears When a vehicle is detected running ahead of you, the system automatically deceler- ates your vehicle.
Page 234 4-5. Using the driving support systems switch is released becomes the set the switch is pressed speed. Large adjustment: Increases or decreases in 5 km/h (3.1 mph) or 5 mph (8 km/h) increments for as long as the switch is held In the constant speed control mode (P.234), the set speed will be increased or decreased as follows:...
Page 235 4-5. Using the driving support systems Canceling and resuming the speed control Long Medium Short Pressing the cancel switch can- The vehicle-to-vehicle distance is set automatically to long mode when the cels the speed control. power switch is turned to ON. The speed control is also canceled If a vehicle is running ahead of you, the when the brake pedal is depressed.
Page 236 4-5. Using the driving support systems Immediately after the switch is pressed, the dynamic radar cruise control indica- tor will come on. Afterwards, it switches to the cruise control indicator. Switching to constant speed control mode is only possible when operating the switch with the cruise control off.
Page 237 After accelerat- than the above, there may be a malfunc- ing, the set speed resumes. However, tion in the system. Contact your Toyota during vehicle-to-vehicle distance con- dealer. trol mode, the vehicle speed may decrease below the set speed in order ■...
Page 238 4-5. Using the driving support systems ● Motorcycles traveling in the same lane ● When steering wheel operation or your position in the lane is unstable ● When water or snow thrown up by the surrounding vehicles hinders the detecting of the sensor ●...
Page 239 4-5. Using the driving support systems Cruise control Setting the vehicle speed Press the cruise control main : If equipped switch to activate the cruise con- Use the cruise control to main- trol. tain a set speed without oper- Cruise control indicator will come on. ating the accelerator pedal.
Page 240 4-5. Using the driving support systems desired set speed is obtained. Pressing the “+RES” switch resumes the constant speed control. Resuming is available when the vehicle speed is more than approximately 30km/h (20 mph). ■ Cruise control can be set when The shift lever is in D.
Page 241 BSM (Blind Spot Moni- may be a malfunction in the cruise con- tor) trol system. Have the vehicle inspected by your Toyota dealer. : If equipped WARNING The Blind Spot Monitor is a ■ To avoid operating the cruise...
Page 242 10 minutes. If the warning message mirror indicator may be difficult to see. does not disappear, have the vehicle ■ inspected by your Toyota dealer. When “Blind Spot Monitor Unavail- able” is shown on the multi-infor- mation display Ice, snow, mud, etc., may be attached to the rear bumper around the sensors.
Page 243 Do not paint the rear bumper any ● ● Do not subject a sensor or its sur- color other than an official Toyota rounding area on the rear bumper color. to a strong impact. If a sensor is moved even slightly...
Page 244 4-5. Using the driving support systems Vehicles that are traveling in areas that are not visible using the outside rear view mirrors (the blind spots) Vehicles that are approaching rapidly from behind in areas that are not visible using the outside rear view mirrors (the blind spots) ■...
Page 245 4-5. Using the driving support systems ■ between your vehicle and another Conditions under which the Blind vehicle is changing Spot Monitor will not detect a vehi- • When a vehicle enters a detection area traveling at about the same The Blind Spot Monitor is not designed speed as your vehicle to detect the following types of vehicles...
Page 246 4-5. Using the driving support systems vehicle Toyota parking assist-sensor : If equipped The distance from your vehicle to objects, such as a wall, when parallel parking or maneuvering into a garage is measured by the sensors and communicated via the...
Page 247 Front center sensor detection Rear corner sensor detection WARNING ■ Rear center sensor detection When using the Toyota parking assist-sensor  Audio system screen Observe the following precautions. Failing to do so may result in the vehi- A graphic will be displayed on the audio cle being unable to be driven safely system screen.
Page 248 10 km/h (6 mph). sensor malfunction, etc. Have the A shift lever other than P. ● vehicle checked by your Toyota dealer. ■ If “Parking Assist Unavailable” is displayed on the multi-information The Toyota parking assist-sensor ●...
Page 249 4-5. Using the driving support systems Also, due to ice forming on a sensor at ● A sensor is frozen. (Thawing the area low temperatures, a warning message will resolve this problem.) may be displayed or the sensor may not In especially cold weather, if a sensor be able to detect an object.
Page 250 4-5. Using the driving support systems  When the operating function is Setting the buzzer volume disabled manually. ■ Adjusting the buzzer volume  When the power switch is turned The buzzer volume can be adjusted off. on the multi-information display. Use the meter control switches to Sensor detection display, change settings.
Page 251 4-5. Using the driving support systems center sensor) Multi-information display Audio system screen Head-up display : Automatic buzzer mute function is enabled. (P.250)  Approximate distance to object: 100 cm (3.3 ft.) to 60 cm (2.0 ft.) (Front center sensor) Multi-information display Audio system screen Head-up display...
Page 252 4-5. Using the driving support systems Head-up display Multi-information display Audio system screen : Automatic buzzer mute function is disabled. (P.250) : The distance segments will blink slowly.  Approximate distance to object: Less than 15 cm (0.5 ft.) Head-up display Multi-information display Audio system screen : Automatic buzzer mute function is disabled.
Page 253 4-5. Using the driving support systems detected, both outside rear view mirror RCTA (Rear Cross Traffic indicators will flash. Alert) function Audio system screen : If equipped If a vehicle approaching from the right or left at the rear of the vehicle is The RCTA function uses the detected, the RCTA icon (P.253) for BSM rear side radar sensors...
Page 254 4-5. Using the driving support systems ■ Rear side radar sensors WARNING P.240 ■ Cautions regarding the use of the function Setting the buzzer volume The driver is solely responsible for safe driving. Always drive safely, tak- ■ Adjusting the buzzer volume ing care to observe your surroundings.
Page 255 4-5. Using the driving support systems RCTA function ■ Operation of the RCTA function The RCTA function uses rear side radar sensors to detect vehicles approaching from the right or left at the rear of the vehicle and alerts the driver of the presence of such vehicles by flashing the outside rear view mirror indicators and sounding a buzzer.
Page 256 4-5. Using the driving support systems The buzzer can alert the driver of Guardrails, walls, signs, parked vehi- ● faster vehicles approaching from cles and similar stationary objects farther away. Small motorcycles, bicycles, pedestri- ● ans, etc. Example: ● Vehicles moving away from your vehi- Approaching vehi- Approximate cle speed...
Page 257 4-5. Using the driving support systems • When the distance between your vehi- cle and metal objects, such as a guardrail, wall, sign, or parked vehicle, which may reflect electrical waves toward the rear of the vehicle, is short • When a towing eyelet is installed to the rear of the vehicle •...
Page 258 4-5. Using the driving support systems When Sport mode is selected, Sport Driving mode select mode indicator comes on. switch Eco drive mode Helps the driver accelerate in an The driving modes can be eco-friendly manner and improve fuel selected to suit the driving and economy through moderate throttle characteristics and by controlling the usage conditions.
Page 259 Operating noise may be heard from the engine compartment turns on and the Trail Mode indicator illuminates on the multi-information dis- ■ When an inspection at your Toyota play. dealer is necessary In the following situations, the system When the switch is pressed again, the may be malfunctioning.
Page 260 4-5. Using the driving support systems ● When the slip indicator illuminates Driving assist systems while Trail Mode is on When the Trail Mode indicator does ● not illuminate even though the Trail To keep driving safety and per- Mode switch is pressed formance, the following sys- tems operate automatically in response to various driving sit-...
Page 261 4-5. Using the driving support systems ity when swerving on slippery road ■ VDIM (Vehicle Dynamics Inte- surfaces by controlling steering per- grated Management) formance. Provides integrated control of the ABS, brake assist, TRC, VSC, ■ TRC (Traction Control) hill-start assist control and EPS Helps to maintain drive power and systems prevent the drive wheels from spin-...
Page 262 TRC is temporary deactivated. If the you to rock the vehicle in order to free it. information continues to show, contact your Toyota dealer. To turn the TRC system off, quickly ■ press and release the switch.
Page 263 4-5. Using the driving support systems vehicle body and steering. the TRC will turn on when vehicle • A motor sound may be heard also speed increases after the vehicle comes to a stop. If both the TRC and VSC systems are turned off, automatic re-enabling will ■...
Page 264 4-5. Using the driving support systems ● Components are damaged ■ TRC/VSC may not operate effec- ■ tively when Secondary Collision Brake auto- Directional control and power may not matic cancellation (if equipped) be achievable while driving on slip- The system is automatically canceled in pery road surfaces, even if the any of the following situations.
Page 265 The ABS, TRC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and the suspen-...
Page 266 4-6. Driving tips Hybrid vehicle driving 4-6.Driving tips Accelerator pedal/brake tips pedal operation  Drive your vehicle smoothly. For economical and ecological Avoid abrupt acceleration and driving, pay attention to the fol- deceleration. Gradual accelera- lowing points: tion and deceleration will make more effective use of the electric motor (traction motor) without Using Eco drive mode...
Page 267 4-6. Driving tips ing overuse of the accelerator inflation pressure can cause poor pedal. Doing so can help control fuel economy. excessive gasoline consumption. Also, as snow tires can cause large amounts of friction, their use on dry roads can lead to poor fuel econ- Highway driving omy.
Page 268 Repairing or replacing snow tires Failure to do so may result in a loss of Request repairs or replacement of vehicle control and cause death or snow tires from Toyota dealers or serious injury. legitimate tire retailers. This is because the removal and Use tires of the specified size.
Page 269 Have around the tires or on the brakes. the vehicle inspected by your Toyota dealer immediately.  Remove any snow or mud from the bottom of your shoes before getting in the vehicle.
Page 270 4-6. Driving tips Side chain (10 mm [0.39 in.] in Utility vehicle precau- width) tions Side chain (30 mm [1.18 in.] in length) This vehicle belongs to the utility vehicle class, which has Cross chain (4 mm [0.16 in.] in higher ground clearance and diameter) narrower tread in relation to...
Page 271 4-6. Driving tips cautions to ensure your driving WARNING enjoyment and to help prevent the ■ Utility vehicle precautions closure of areas to off-road vehi- Always observe the following precau- cles: tions to minimize the risk of death, serious injury or damage to your vehi- ...
Page 272 4-6. Driving tips ■ When you drive through water WARNING If driving through water, such as when After driving through tall grass, ● crossing shallow streams, first check mud, rock, sand, rivers, etc., check the depth of the water and the bottom that there is no grass, bush, paper, of the riverbed for firmness.
Page 273 Interior features 5-1. Using the air conditioning system and defogger Front automatic air conditioning system ......272 Rear automatic air condition- ing system ......278 Seat heaters/seat ventilators ........281 5-2. Using the interior lights Interior lights list....283 5-3. Using the storage features List of storage features ..286 Luggage compartment features...
Page 274 5-1. Using the air conditioning system and defogger Front automatic air conditioning system 5-1.Using the air conditioning system and defogger Air outlets and fan speed are automatically adjusted according to the temperature setting. Air conditioning controls Automatic mode switch (P.275) Left-hand side temperature control switch “OFF”...
Page 275 5-1. Using the air conditioning system and defogger temperature. If “A/C” switch is not pressed, the sys- tem will blow ambient temperature air or heated air. The temperature for the driver, front passenger and rear seats can be adjusted separately when: ...
Page 276 5-1. Using the air conditioning system and defogger Set the outside/recirculated air mode ■ When driving on dusty roads switch to outside air mode if the recircu- Close all windows. If dust thrown up by the vehicle is still drawn into the vehicle lated air mode is used.
Page 277 5-1. Using the air conditioning system and defogger To stop the operation, press the • The start timing of the blower may be delayed for a short period of time “OFF” switch. immediately after the air conditioning system is started in automatic mode. If the fan speed setting or air flow modes are operated, the automatic ■...
Page 278 5-1. Using the air conditioning system and defogger Using front seat concen- trated airflow mode (S-FLOW) Directing airflow to the front seats only and to all seats can be switched via switch operation. When the front passenger seat is not occupied, airflow may switch to ■...
Page 279 5-1. Using the air conditioning system and defogger WARNING ■ To not interrupt the windshield defogger from operating Do not place anything on the instru- ment panel which may cover the air outlets. Otherwise, air flow may be obstructed, preventing the windshield defoggers from defogging.
Page 280 5-1. Using the air conditioning system and defogger Rear automatic air conditioning system The air outlets and fan speed are automatically adjusted according to the temperature setting. The rear air conditioning system can be operated using the front air conditioning control panel and rear air conditioning control panel. Press the “REAR CLIMATE”...
Page 281 5-1. Using the air conditioning system and defogger ■ Front air conditioning control panel Rear air conditioning system on/off switch “REAR CLIMATE” switch The mode switches between the rear air conditioning control mode and front air conditioning control mode each time the “REAR CLIMATE” switch is pressed. Rear seat temperature contorl knob To set temperature, move the rear seat temperature control knob upward or down- ward.
Page 282 5-1. Using the air conditioning system and defogger the airflow mode control switch. Feet The air outlets used are switched each time the switch is pressed. Using automatic mode Press the automatic mode switch. Adjust the temperature setting. To stop the operation, press the “OFF”...
Page 283 5-1. Using the air conditioning system and defogger ■ Adjusting the position of and Seat heaters /seat venti- opening and closing the air lators outlets Adjusting the position of and open- : If equipped ing and closing the air outlets ...
Page 284 5-1. Using the air conditioning system and defogger Seat heaters WARNING ■ To prevent overheating and ■ Front minor burn injuries Each time the switch is pressed, Observe the following precautions when using the seat heaters. the operation condition changes as follows.
Page 285 5-2. Using the interior lights Interior lights list 5-2.Using the interior lights Location of the interior lights Front personal lights (P.284) Front interior lights (P.284) Shift lever light Open tray lights (if equipped) Door courtesy lights Ambient lights (if equipped) Rear personal lights (if equipped) (P.284) Rear personal lights (if equipped) (P.284) Rear interior light (P.284)
Page 286 5-2. Using the interior lights Operating the interior lights ■ Front interior lights ■ Rear personal lights Turns the lights on/off Vehicles without panoramic  Turns the lights on/off linked to moon roof door positions Turns the lights on Turns the lights off ■...
Page 287 5-2. Using the interior lights ■ To prevent the 12-volt battery from being discharged If the interior lights remain on when the power switch is turned off, the lights will go off automatically after 20 minutes. ■ The interior lights may turn on automatically when If any of the SRS airbags deploy (inflate) or in the event of a strong rear impact,...
Page 288 5-3. Using the storage features List of storage features 5-3.Using the storage features Location of the storage features Auxiliary boxes (if equipped) (P.288) Open tray (P.289) Glove box (P.287) Bottle holders (P.288) Cup holders (P.287) Console box (P.287) Lighters or spray cans may ●...
Page 289 5-3. Using the storage features WARNING ■ When storage compartments are not in use When driving or when the storage compartments are not in use, keep the lids closed. In the event of sudden braking or sud- den swerving, an accident may occur due to an occupant being struck by an open lid or the items stored inside.
Page 290 5-3. Using the storage features Second seats  Bottle holders Pull the armrest down. Front doors  Third seats  Rear doors  WARNING ■ Bottle holders ■ Items unsuitable for the cup ● When storing a bottle, close the cap. holder Do not place anything other than ●...
Page 291 5-3. Using the storage features Open tray Instrument panel  Driver’s side instrument panel  Pull the tab to open. Front of console  WARNING ■ Items unsuitable for storing (Overhead) ■ Cable pass through (Instrument Do not store items heavier than 200 g panel) (0.44 lb.).
Page 292 5-3. Using the storage features Luggage compartment WARNING features ■ Items unsuitable for the open tray Observe the following precautions Cargo hooks when putting items in the open tray. Failure to do so may cause items to Pull down the hook to use. be thrown out of the tray in the event of sudden braking or steering.
Page 293 5-3. Using the storage features (P.293) and take out the lug- WARNING gage cover unit. ■ When the cargo net is not in use To avoid injury, always return the hooks to their stowed positions when not in use. Grocery bag hooks ■...
Page 294 5-3. Using the storage features the other end and insert it into Compress the end of the lug- the other recess. gage cover and lift the luggage cover up. Pull out the luggage cover and hook it onto the anchors. ■...
Page 295 5-3. Using the storage features Auxiliary boxes WARNING ■ Luggage cover Center deck under tray  When installing/stowing the lug- ● Pull the strap upwards to open the gage cover, make sure that the lug- gage cover is securely center deck board. installed/stowed.
Page 296 5-4. Using the other interior features Other interior features 5-4.Using the other interior features ■ The USB charging ports can be used when The power switch is in ACC or ON. USB charging ports ■ Situations in which the USB charg- The USB charging ports are used ing ports may not operate correctly to supply 2.1 A of electricity at 5 V...
Page 297 5-4. Using the other interior features NOTICE Do not push down on or apply ● unnecessary force to an external device or the cable of an external device while it is connected. ■ To prevent 12-volt battery dis- charge Do not use the USB charging ports for a long period of time with the hybrid system stopped.
Page 298 5-4. Using the other interior features WARNING ■ Items that must not be hung on the hook Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.
Page 299 5-4. Using the other interior features To set the visor in the forward position, flip it down. To set the visor in the side posi- tion, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it backward.
Page 300 5-4. Using the other interior features slightly to unhook the shade from the Compass anchors, and lower it slowly. : If equipped The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. Operation and displays To turn the compass on or off, press NOTICE and hold the switch for 3 seconds.
Page 301 5-4. Using the other interior features after turning. NOTICE ● The vehicle is on an inclined surface. ■ To avoid compass malfunctions ● The vehicle is in a place where the Do not place magnets or any metal earth’s magnetic field is subject to objects near the inside rear view mir- interference by artificial magnetic ror.
Page 302 5-4. Using the other interior features The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geo- graphic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.
Page 303 Maintenance and care 6-1. Maintenance and care Cleaning and protecting the vehicle exterior ....302 Cleaning and protecting the vehicle interior ....305 6-2. Maintenance Maintenance requirements ........307 Scheduled maintenance ...309 6-3. Do-it-yourself maintenance Do-it-yourself service precau- tions ........315 Hood .........317 Positioning a floor jack..318 Engine compartment ..319...
Page 304 6-1. Maintenance and care may also be an increased risk of dam- Cleaning and protecting 6-1.Maintenance and care age to vehicle. the vehicle exterior ■ High pressure car washes As water may enter the cabin, do not bring the nozzle tip near the gaps Perform cleaning in a manner around the doors or perimeter of the appropriate to each compo-...
Page 305 ■ chipped or scratched, the system may When cleaning the windshield malfunction.If this occurs, consult (vehicles with rain-sensing wind- your Toyota dealer. shield wipers) Set the wiper switch to off. If the switch is in “AUTO”, the wipers NOTICE may operate unexpectedly in the fol- lowing situations, and may result in ■...
Page 306 6-1. Maintenance and care Keep the cleaning nozzle at least ● NOTICE 30 cm (11.9 in.) away from the vehi- To prevent the wheels from corrod- ● cle body. Otherwise resin section, ing, remove any dirt and store in a such as moldings and bumpers, place with low humidity when stor- may be deformed and damaged.
Page 307 6-1. Maintenance and care Cleaning and protecting WARNING the vehicle interior ■ Water in the vehicle Do not splash or spill liquid in the ● vehicle, such as on the floor, in the Perform cleaning in a manner hybrid battery (traction battery) air appropriate to each compo- vents, and in the luggage compart- ment.
Page 308 ■ Caring for leather areas tem above or under the floor of the Toyota recommends cleaning the inte- vehicle. Water may also cause the rior of the vehicle at least twice a year body to rust.
Page 309 Doesn’t that seem like the best way? essential. Toyota recommends Your Toyota dealer has invested a lot of the following maintenance: money in special Toyota tools and ser- vice equipment. It helps them to do the WARNING job better and at less cost.
Page 310 ● Engine coolant temperature continu- ally higher than normal (P.69) If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. Your vehicle may need adjustment or repair. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 311 6-2. Maintenance Scheduled maintenance Perform maintenance by the schedule as follows: Maintenance schedule requirements Your vehicle needs to be serviced according to the normal maintenance schedule. (See “Maintenance schedule”.) If you mainly operate your vehicle under one or more of the special operat- ing conditions below, some of the maintenance schedule items need to be serviced more frequently in order to keep your vehicle in good condition.
Page 312 6-2. Maintenance SERVICE INTERVAL: ODOMETER READING (Odometer reading or x1000 km 10 20 30 40 50 60 70 80 MONTHS months, whichever x1000 miles 12 18 24 30 36 42 48 comes first.) BASIC ENGINE COMPONENTS 1 Engine oil 2 Engine oil filter Cooling and heater system <<See note 1.>>...
Page 313 4. Including the filter in fuel tank. 5. For Iraq, Bahrain, Qatar, Kuwait, the United Arab Emirates, Saudi Arabia, and Oman only. 6. Toyota genuine fuel injector cleaner or equivalent. 7. Parking brake inspection is not necessary. 8. Integrated in rear transaxle.
Page 314 6-2. Maintenance Additional maintenance schedule Refer to the following table for normal maintenance schedule items requir- ing more frequent service specific to the type of severe conditions. (For out- line, see “Maintenance schedule requirements”.) A-1: Operating on rough or muddy roads, or roads with melted snow. Every 5000 km (3000 miles) or 3 months ...
Page 315 6-2. Maintenance B-1: Heavily loaded vehicle. (For example, using a car top carrier and so forth.) I: Every 40000 km (24000 miles) or 24  Inspection or replacement of hybrid months transmission fluid (including front dif- R: Every 80000 km (48000 miles) or 48 ferential) months I: Every 40000 km (24000 miles) or 24...
Page 316 6-2. Maintenance springs retaining U bolts. 2. Integrated in rear transaxle. : Perform correction or replacement as necessary. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 317 6-3. Do-it-yourself maintenance Do-it-yourself service 6-3.Do-it-yourself maintenance Items Parts and tools precautions • “Toyota Genuine Motor Oil” or equiv- alent If you perform maintenance by Engine oil level • Rag or paper towel yourself, be sure to follow the (P.319) •...
Page 318 6-3. Do-it-yourself maintenance ■ Safety glasses WARNING Wear safety glasses to prevent flying The engine compartment contains or falling material, fluid spray, etc. many mechanisms and fluids that from getting in your eyes. may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe NOTICE the following precautions.
Page 319 6-3. Do-it-yourself maintenance Hood WARNING ■ Pre-driving check Check that the hood is fully closed Opening the hood and locked. Pull the hood lock release lever. If the hood is not locked properly, it may open while the vehicle is in The hood will pop up slightly.
Page 320 6-3. Do-it-yourself maintenance ■ Positioning a floor jack Rear When using a floor jack, follow the instructions in the manual provided with the jack and per- form the operation safely. When raising your vehicle with a floor jack, position the jack correctly.
Page 321 6-3. Do-it-yourself maintenance Engine compartment Components Engine coolant reservoir (P.322) Fuse boxes (P.346) Engine oil filler cap (P.320) Engine oil level dipstick (P.320) Air cleaner (P.323) Washer fluid tank (P.323) Electric cooling fan Condenser (P.323) Radiator (P.323) Power control unit coolant reservoir (P.322) Checking and adding the ■...
Page 322 6-3. Do-it-yourself maintenance oil level on the dipstick. depending on the type of vehicle or engine. ■ Checking the engine oil Wipe the dipstick and reinsert it Park the vehicle on level fully. ground. After warming up the ■ Checking the oil type and pre- engine and turning off the hybrid paring the item needed system, wait more than 5 min-...
Page 323 Call your Toyota dealer, service sta- press and hold tion or auto parts store for informa- tion concerning recycling or Press of the meter con- disposal.
Page 324 “FULL” line. voir caps, drain cock and water pump. If you cannot find a leak, have your (P.403) Toyota dealer test the cap and check for leaks in the cooling system. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 325 ■ Diluting washer fluid inspected by your Toyota dealer. Dilute washer fluid with water as nec- essary. Refer to the freezing temperatures WARNING listed on the label of the washer fluid ■...
Page 326 6-3. Do-it-yourself maintenance Release the clips. WARNING ■ To prevent inhaling dust Wear a respirator when using com- pressed air to clean the air cleaner fil- ter. NOTICE ■ To prevent damaging the engine Do not drive with the air cleaner filter removed.
Page 327 6-3. Do-it-yourself maintenance 12-volt battery Location The 12-volt battery is located in the right-hand side of luggage compart- ment. Exterior Make sure that the 12-volt battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps. Before removing the 12-volt battery cover Open the deck board.
Page 328 If the system will not start even after at least 15 minutes and get immedi- multiple attempts at all the methods ate medical attention. If possible, above, contact your Toyota dealer. continue to apply water with a sponge or cloth while traveling to the nearest medical facility.
Page 329 Failure to do so may cause Keep away from children gas (hydrogen) to enter the passen- ger compartment, causing a fire or explosion. For replacement of the 12-volt battery, contact your Toyota dealer. Explosive gas ■ When handling the 12-volt bat- tery ...
Page 330 If you are not sure, consult with your Check the spare tire condition and Toyota dealer. pressure if not rotated. ■ Tire life Any tire over 6 years old must be...
Page 331 If the spare tire cannot be lowered, the tion, driving on rough roads may wire cable may be severed. Have the cause damage to the tires them- vehicle inspected at your Toyota dealer. selves, as well as the vehicle’s wheels and body. ■...
Page 332 In the following cases, the tire pres- ● sure warning system may not operate properly. • If non-genuine Toyota wheels are used.  If the tire pressure drops below a • A tire has been replaced with a tire predetermined level, the driver is that is not an OE (Original Equipment) tire.
Page 333 6-3. Do-it-yourself maintenance • A tire has been replaced with a tire • When carrying a portable radio, cellu- that is not of the specified size. lar phone, cordless phone or other • Tire chains, etc. are equipped. wireless communication device •...
Page 334 Have tire pressure warning valves valve and transmitter may not operate and transmitter ID codes regis- properly. If a liquid sealant is used, contact your Toyota dealer or other tered by your Toyota dealer. qualified service shop as soon as (P.335) possible.
Page 335 6-3. Do-it-yourself maintenance Adjust the tire inflation pressure ■ How to initialize the tire pres- to the specified cold tire inflation sure warning system pressure level. (P.415) 4.2-inch display  Make sure to adjust the tire pressure to Park the vehicle in a safe place the specified cold tire inflation pressure and turn the power switch off.
Page 336 If you accidentally restart the initializa- ● inspected by your Toyota dealer. tion when initialization is not neces- sary, adjust the tire inflation pressure to the specified level when the tires are cold, and conduct initialization...
Page 337 6-3. Do-it-yourself maintenance Press of the meter WARNING control switch, select ■ When initializing the tire pres- sure warning system then press and hold Do not initializing tire inflation pres- sure without first adjusting the tire Press of the meter inflation pressure to the specified level.
Page 338 6-3. Do-it-yourself maintenance 7-inch display Drive the vehicle at approxi-  mately 40 km/h (25 mph) or Park the vehicle in a safe place more for approximately 10 to 30 and turn the power switch off. minutes. Initialization cannot be performed while the vehicle is moving.
Page 339 If the ID codes cannot be registered have been canceled correctly. To can- even when performing the above proce- cel registration, perform the ID code dure, contact your Toyota dealer. registration start procedure again and then turn the power switch off before driving.
Page 340 Damage to the drive train ● while driving (due to road hazards, If a tire needs frequent inflating, have it expansion joints, sharp edges in the checked by your Toyota dealer. road, etc.) ■ Instructions for checking tire infla- tion pressure...
Page 341 Whenever wheels are Toyota dealer or other qualified ser- replaced, tire pressure warning valves vice shop. In addition, make sure to and transmitters must be installed.
Page 342 Aluminum wheel precau- Removing the air condition- tions ing filter  Use only Toyota wheel nuts and Turn the power switch off. wrenches designed for use with Open the glove box. Slide off your aluminum wheels.
Page 343 6-3. Do-it-yourself maintenance heavy traffic flow, early replacement ), and remove the filter may be required. (P.309) cover. ■ If air flow from the vents decreases dramatically The filter may be clogged. Check the fil- ter and replace if necessary. NOTICE ■...
Page 344 6-3. Do-it-yourself maintenance Cleaning the hybrid bat- If dust and clogs cannot be tery (traction battery) completely removed air intake vents and fil- If dust and clogs cannot be com- pletely removed with the air intake vent cover installed, remove the To prevent the fuel economy cover and clean the filter.
Page 345 If you have any con- cerns about cleaning the filter, contact your Toyota dealer. ■ If “Maintenance Required for Trac- tion Battery Cooling Parts See Owner’s Manual”...
Page 346 ● Carefully handle the removed filter so that it will not be damaged. If the filter is damaged, have it replaced with a new filter by your Toyota dealer. Make sure to reinstall the filter and ● cover to their original positions after cleaning.
Page 347  Lithium battery CR2032 ■ Use a CR2032 lithium battery Batteries can be purchased at your ● Toyota dealer, local electrical appli- ance shops or camera stores. Replace only with the same or equiva- ● lent type recommended by the manu- facturer.
Page 348 6-3. Do-it-yourself maintenance nal facing up. Checking and replacing fuses If any of the electrical compo- nents do not operate, a fuse may have blown. If this hap- pens, check and replace the fuses as necessary. Checking and replacing WARNING fuses ■...
Page 349 6-3. Do-it-yourself maintenance Under the driver’s side instru- Replace the blown fuse with a new fuse  of an appropriate amperage rating. The ment panel amperage rating can be found on the Remove the lid. fuse box lid. Type A Make sure to push the claw when ...
Page 350 Have the cause of electrical overload If the replaced fuse blows again, have ● determined and repaired by your the vehicle inspected by your Toyota Toyota dealer as soon as possible. dealer. ■ If there is an overload in a circuit The fuses are designed to blow, protect- ing the wiring harness from damage.
Page 351 Back-up lights License plate lights Bulb locations ■ Lights that need to be Front (type A) replaced by your Toyota dealer   Headlight low beams  Headlight high beams  Front position lights  Daytime running lights (type A) ...
Page 352 LED lights The lights other than the following lights each consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. ● Front turn signal lights Rear turn signal lights ●...
Page 353 6-3. Do-it-yourself maintenance Disconnect the wire harness. the bulb base and light unit. ■ Rear turn signal lights Turn the bulb base Open the back door and using a counterclockwise and remove it. flathead screwdriver, remove the cover. To prevent damage to the vehicle, wrap the tip of the flathead screwdriver with tape, etc.
Page 354 6-3. Do-it-yourself maintenance Install the cover. base and light unit. ■ Rear fog lights For the left side  Remove the 3 screws and 2 clips, and push up the under Install the light unit. cover. Align the 2 guides and push the light When removing a clip, use a flathead unit toward the front of the vehicle to install it.
Page 355 6-3. Do-it-yourself maintenance While pressing the lock release, unit. disconnect the connector. Turn the bulb base counterclockwise and remove it. Install the under cover with the 3 screws and 2 clips. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning it clockwise and Install the con- nector.
Page 356 6-3. Do-it-yourself maintenance clockwise and Install the con- and then remove the whole clip. nector. After installing the bulb base and con- necting the connector, wiggle them lightly to make sure they are securely installed and turn the lights on to vis- ually check that there is no light leaking from between the bulb base and light unit.
Page 357 6-3. Do-it-yourself maintenance the cover. to visually check that there is no light leaking from between the bulb base To prevent damage to the vehicle, wrap and light unit. the tip of the flathead screwdriver with tape, etc. Install the cover. Turn the bulb base Align the tabs of the cover with the counterclockwise and remove it.
Page 358 6-3. Do-it-yourself maintenance shown in the illustration, disen- tape, etc. gage the hook, and then remove the lens. To prevent damage to the vehicle, wrap the tip of the screwdriver with tape, etc. Remove the light bulb. Remove the lens. Install a new light bulb.
Page 359 6-3. Do-it-yourself maintenance Install the lens. WARNING ■ To prevent injury Before performing any light bulb replacement procedure, be sure to turn the power switch off. Failure to do so may result in burns from hot com- ponents or a part of your body may get caught on an operating compo- nent, possibly causing serious injury.
Page 360 6-3. Do-it-yourself maintenance HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 361 When trouble arises 7-1. Essential information Emergency flashers..360 If your vehicle has to be stopped in an emergency ........360 If the vehicle is trapped in rising water.......361 7-2. Steps to take in an emer- gency If your vehicle needs to be towed ......363 If you think something is wrong...
Page 362 7-1. Essential information Emergency flashers If your vehicle has to be 7-1.Essential information stopped in an emer- gency The emergency flashers are used to warn other drivers when the vehicle has to be Only in an emergency, such as stopped on the road due to a if it becomes impossible to breakdown, etc.
Page 363 However, an emergency hammer can not shatter the windshield as it is laminated glass. : Contact your Toyota dealer or aftermarket accessory manufac- turer for further information about an emergency hammer. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 364 7-1. Essential information WARNING ■ Escaping the vehicle from the window There are cases where escaping the vehicle from the window is not possi- ble due to seating position, passenger body type, etc. When using an emergency hammer, consider your seat location and the size of the window opening to ensure that the opening is accessible and large enough to escape.
Page 365 If the vehicle is towed with the front wheels ommend having your vehicle contacting the ground, the drivetrain towed by your Toyota dealer or and related parts may be damaged or electricity generated by the operation commercial towing service,...
Page 366 Do not turn the power switch off. ● lem with your transmission. Contact There is a possibility that the steer- ing wheel is locked and cannot be your Toyota dealer or commercial operated. towing service before towing. ■ Installing towing eyelets to the ...
Page 367 7-2. Steps to take in an emergency From the front (AWD models)  AWD models  Using a flatbed truck Use a towing dolly under the rear wheels. If your vehicle is transported by a flatbed truck, it should be tied down From the rear ...
Page 368 7-2. Steps to take in an emergency cle body as shown in the illustration. NOTICE ■ Using a flatbed truck Do not overly tighten the tie downs or the vehicle may be damaged. Emergency towing If a tow truck is not available in an emergency, your vehicle may be temporarily towed using cables or Insert the towing eyelet into the...
Page 369 Turn automatic mode off. (P.170) ing symptoms, your vehicle When the shift lever cannot be shifted: probably needs adjustment or P.167 repair. Contact your Toyota ■ While towing dealer as soon as possible. If the hybrid system is off, the power...
Page 370 7-2. Steps to take in an emergency  Vehicle pulls heavily to one side when driving on a level road  Loss of brake effectiveness, spongy feeling, pedal almost touches the floor HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 371  The brake fluid level is low; or  The brake system is malfunctioning  Immediately stop the vehicle in a safe place and contact (red) your Toyota dealer. Continuing to drive the vehicle may be dangerous. ■ Brake system warning light...
Page 372 Toyota dealer. ■ SRS warning light Warning light Details/Actions Indicates a malfunction in:  The SRS airbag system; or  The seat belt pretensioner system  Have the vehicle inspected by your Toyota dealer immedi- ately. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 373 ABS warning light Warning light Details/Actions Indicates a malfunction in:  The ABS; or  The brake assist system  Have the vehicle inspected by your Toyota dealer immedi- ately. ■ Brake Override System warning light/Drive-Start Control warning light (warning buzzer)
Page 374 Details/Actions When the light comes on after blinking for approximately 1 minute: Malfunction in the tire pressure warning system  Have the system checked by your Toyota dealer. When the light comes on: Low tire inflation pressure such as  Natural causes ...
Page 375 Toyota parking assist-sensor OFF indicator (warning buzzer) Warning light Details/Actions Indicates a malfunction in the Toyota parking assist-sensor func- tion  Have the vehicle inspected by your Toyota dealer immedi- ately. (flashes) Indicates that the system is temporarily unavailable, possibly due (if equipped) to a sensor being dirty or covered with ice, etc.
Page 376 When a buzzer sounds simultaneously: Indicates a malfunction has occurred in the PCS (Pre-Collision System).  Have the vehicle inspected by your Toyota dealer immedi- ately. When a buzzer does not sound: The PCS (Pre-Collision System) has become temporarily unavail-...
Page 377 ■ Brake hold operated indicator Warning light Details/Actions Indicates a malfunction in the brake hold system  Have the vehicle inspected by your Toyota dealer immedi- (flashes) ately. ■ Speed warning light (warning buzzer) Warning light Details/Actions Indicates that your vehicle speed reaches 120 km/h (75 mph).
Page 378 The vehicle will become extremely been performed, have the vehicle unstable during braking, and the ABS inspected by your Toyota dealer immedi- system may fail, which could cause ately. an accident resulting in death or seri- ous injury.
Page 379 (P.369) If a warning message is dis- played again after the appro- priate actions have been performed, contact your Toyota dealer. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 380 Messages and warnings The warning lights and warning buzzers operate as follows depending on the content of the message. If a message indicates the need for inspection by a dealer, have the vehicle inspected by your Toyota dealer immediately. Warning light Warning Warning buzzer ...
Page 381 The following systems may be malfunc- cannot be charged when the shift lever tioning. Have the vehicle inspected by is in N, shift the shift lever to P when the your Toyota dealer immediately. vehicle is stopped. ● Automatic High Beam (if equipped) ■...
Page 382 7-2. Steps to take in an emergency vehicle inspected by your Toyota dealer. shown on the multi-information dis- play, follow the instructions. ■ If “Speed Limit Exceeded” is dis- • “Engine Coolant Temp High Stop in a played Safe Place See Owner's Manual”...
Page 383 7-2. Steps to take in an emergency If you have a flat tire Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire. For details about tires: P.328 WARNING ■ If you have a flat tire Do not continue driving with a flat tire.
Page 384 7-2. Steps to take in an emergency Location of the spare tire, jack and tools Jack handle Towing eyelet Wheel nut wrench Adapter socket Jack Spare tire ● Only use the tire jack that comes WARNING with this vehicle for replacing a flat ■...
Page 385 7-2. Steps to take in an emergency Taking out the jack WARNING Put the jack properly in its jack ● Pull the strap upwards and open point. the center deck board. Do not put any part of your body ● under the vehicle while it is sup- ported by the jack.
Page 386 7-2. Steps to take in an emergency Remove the jack after removing can use your key. the hook. Attach the adapter socket to the spare tire clamp bolt. Taking out the spare tire Pull the strap upwards and open the center deck board. Connect the jack handle exten- sion to the jack handle.
Page 387 7-2. Steps to take in an emergency quickly, the wire cable may slip off of bracket from the hoist the shaft inside the unit and the tire may assembly not be lowered. If the spare tire cannot be lowered: P.387 Pull out the spare tire and stand it against the bumper.
Page 388 7-2. Steps to take in an emergency 11Remove the outside spare tire Wheel chock posi- Flat tire cover. tions In front of the front Rear left-hand side right-hand side tire Rear right-hand In front of the front side left-hand side tire Slightly loosen the wheel nuts (one turn).
Page 389 If the spare tire still cannot be lowered, faces up to avoid scratching the wheel the wire cable may be severed. Have surface. the vehicle inspected by your Toyota dealer. WARNING ■ Replacing a flat tire ●...
Page 390 • If there are any cracks or deforma- tions in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • Do not attach a heavily damaged wheel ornament, as it may fly off the Install the spare tire and loosely wheel while the vehicle is moving.
Page 391 7-2. Steps to take in an emergency come into contact with the disc wheel. WARNING ■ Stowing the flat tire Failure to follow steps listed under stowing the tire may result in damage to the spare tire carrier and loss of the tire, which could result in serious injury or death.
Page 392 7-2. Steps to take in an emergency Lay the tire on the ground with Pass the hoist assembly the outer surface (valve stem) holding bracket through the facing up. wheel opening. Before raising the tire, make sure that the hoist assembly is perpendicular to the wheel opening.
Page 393 When replacing the tires When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. ■ When stowing the flat tire ●...
Page 394 Toyota dealer. The hybrid system will not start even though the cor- rect starting procedure is being followed. (P.160)
Page 395  One or both of the 12-volt battery terminals may be disconnected. (P.325)  The 12-volt battery may be dis- charged. (P.397) Contact your Toyota dealer if the prob- lem cannot be repaired, or if repair pro- cedures are unknown. Starting the hybrid system in an emergency...
Page 396 If you lose your keys If the fuel filler door can- not be opened New genuine mechanical keys can be made by your Toyota If the fuel filler door opener dealer using another mechani- switch cannot be operated, cal key and the key number...
Page 397 7-2. Steps to take in an emergency During refueling, fuel may spill If the electronic key out from the filler opening due to does not operate prop- air being discharged from inside erly the fuel tank. Therefore, fill the fuel tank carefully and slowly. If communication between the electronic key and vehicle is interrupted (P.122) or the...
Page 398 7-2. Steps to take in an emergency Starting the hybrid system Ensure that the shift lever is in P and depress the brake pedal. Touch the Toyota emblem side of the electronic key to the power switch. When the electronic key is detected, a...
Page 399 (P.162) tem if the vehicle’s 12-volt bat- tery is discharged. You can also call your Toyota dealer or a qualified repair shop. HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 400 7-2. Steps to take in an emergency Open the hood (P.317) and Restarting the hybrid sys- fuse box cover. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your vehicle by following the steps below.
Page 401 Maintain the engine speed of Once the hybrid system starts, the second vehicle and start the have the vehicle inspected at your Toyota dealer as soon as possible. hybrid system of your vehicle by turning the power switch to ON. ■...
Page 402 Vehicles with power back door: The ● cleared. When the 12-volt battery is power back door must be initialized. depleted, have the vehicle inspected (P.118) at your Toyota dealer. ■ ● Some systems may require initializa- When replacing the 12-volt battery tion. (P.428) Use a Central Degassing type 12-volt ●...
Page 403 Hole section of the vehicle Do not smoke, use matches, ciga- ● For details, consult your Toyota dealer. rette lighters or allow open flame near the 12-volt battery. WARNING ■...
Page 404 12-volt battery. ■ After recharging the 12-volt bat- tery Have the 12-volt battery inspected at your Toyota dealer as soon as possi- ble. If the 12-volt battery is deteriorating, continued use may cause the 12-volt battery to emit a malodorous gas, which may be detrimental to the health of passengers.
Page 405 (radiator) for any leaks. your vehicle is overheating. If a large amount of coolant leaks,  The needle of the engine cool- immediately contact your Toyota dealer. ant temperature gauge (P.69) enters the red zone or a loss of hybrid system power is experienced.
Page 406 If a large amount of coolant leaks, fan operates and to check for immediately contact your Toyota dealer. coolant leaks from the radiator or hoses. The fan operates when the air condi- tioning system is turned on immediately after a cold start.
Page 407 Observe the following precautions: However, if the message appears again ● Avoid contaminating the coolant frequently, contact your Toyota dealer. with foreign matter (such as sand or dust, etc.). WARNING Do not use any coolant additive. ● ■...
Page 408 7-2. Steps to take in an emergency If the vehicle becomes WARNING stuck ■ When attempting to free a stuck vehicle If you choose to push the vehicle Carry out the following proce- back and forth to free it, make sure dures if the tires spin or the the surrounding area is clear to avoid striking other vehicles, objects or peo-...
Page 409 Vehicle specifications 8-1. Specifications Maintenance data (fuel, oil level, etc.) .......408 Fuel information ....417 8-2. Customization Customizable features..418 8-3. Initialization Items to initialize ....428 HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 410 Remove the scuff plate. The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identifi- cation number for your Toyota. It is used in registering the ownership of your vehicle. Top left of the instrument panel ...
Page 411 8-1. Specifications Turn back the carpet. lator pad under the wire harness. Install the dash panel insulator Remove the dash panel insula- pad. tor pad. Return the carpet to its original Turn back the floor panel insula- position. tor pad. Install the 2 holes of the carpet to the The vehicle identification number is wire harness clamps.
Page 412 8-1. Specifications install the trim with the nut. ■ Year of manufacture and coun- 10Install the scuff plate. try of origin The year of the manufacture and Insert the 2 guides at the front of the scuff plate into the trim, align the 7 country of origin are shown on the claws with the wire harness clamps, Certification Regulation label.
Page 413 4.5 L (4.8 qt., 4.0 Imp. qt.) oil level on the dipstick. Without fil- 4.2 L (4.4 qt., 3.7 Imp. qt.) ■ Engine oil selection “Toyota Genuine Motor Oil” is used : The engine oil capacity is a reference HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 414 8-1. Specifications in your Toyota vehicle. Use Toyota become difficult to start, so SAE approved “Toyota Genuine Motor 0W-16, 0W-20, 5W-20 or 5W-30 Oil” or equivalent to satisfy the fol- engine oil is recommended. lowing grade and viscosity. Oil viscosity (0W-16 is explained...
Page 415 Power con- 1.9 L (2.0 qt., 1.7 Imp. qt.) trol unit Use either of the following:  “Toyota Super Long Life Coolant”  Similar high-quality ethylene glycol-based non-sili- Coolant type cate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 416 8-1. Specifications : The fluid capacity is a reference quantity. If replacement is necessary, contact your Toyota dealer. NOTICE ■ Hybrid transmission fluid type Using transmission fluid other than the above type may cause abnormal noise or vibration, or ultimately damage the transmission of your vehicle.
Page 417 8-1. Specifications Tires and wheels Type A  Tire size 235/65R18 106V Front tire  250 kPa (2.5 kgf/cm or bar, 36 psi) Tire inflation pressure Rear tire  (Recommended cold tire 250 kPa (2.5 kgf/cm or bar, 36 psi) inflation pressure) Spare ...
Page 418 8-1. Specifications Light bulbs Light bulbs Type Front turn signal lights Rear turn signal lights Exterior Back-up lights Rear fog lights License plate lights Door courtesy lights Vanity lights Interior Rear personal light Rear interior light A: Wedge base bulbs (amber) B: Wedge base bulbs (clear) C: Single end bulbs (clear) HIGHLANDER HV_GE...
Page 419 ■ Use of ethanol blended gasoline in a gasoline engine Toyota allows the use of ethanol blended gasoline where the ethanol content is up to 10%. Make sure that the ethanol blended gasoline to be used has a Research Octane Number that follows the above.
Page 420 Toyota dealer. Press or press and hold The available settings will differ Customizing vehicle fea- depending on if is pressed or tures pressed and held.
Page 421 8-2. Customization Customizable Features Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer for further details. Settings that can be changed using the navigation/multimedia system screen Settings that can be changed using the meter control switches Settings that can be changed by your Toyota dealer Definition of symbols: O = Available, —...
Page 422 8-2. Customization Default setting Customized setting Function Average vehicle Drive information items speed Elapsed time — — (Second item) Distance Eco score Drive information — — Current trip result display — — Speedometer display Average vehicle speed — — Gadget content Distance Elapsed time Total (after reset)
Page 423 8-2. Customization Function Default setting Customized setting Compass — — Audio system operation — — status : If equipped ■ Door lock (P.109, 395) Function Default setting Customized setting Driver’s door All doors Unlocking using a mechan- unlocked in one step, unlocked in one —...
Page 424 8-2. Customization ■ Smart entry & start system (P.109, 121) Function Default setting Customized setting Smart entry & start system — Smart door unlocking All the doors Driver’s door — Number of consecutive 2 times As many as desired — —...
Page 425 8-2. Customization Function Default setting Customized setting Opening/closing of the One short press power back door using the Push twice Press and hold — — switch of the wire- less remote control Operation buzzer while the — — back door is operating Power back door open operation when the back —...
Page 426 8-2. Customization Function Default setting Customized setting Wireless remote control — — linked operation Wireless remote control linked operation signal — — (buzzer) : If equipped ■ Moon roof (P.144) Function Default setting Customized setting Linked operation of compo- nents when mechanical Slide only Tilt only —...
Page 427 8-2. Customization Function Default setting Customized setting Shift position linked rear window wiper operation Only once — — Continuous (P.184) ■ PCS (Pre-Collision System) (P.192) Function Default setting Customized setting PCS (Pre-Collision Sys- — — tem) Early Adjust alert timing Middle —...
Page 428 Alert timing for presence of Late approaching vehicle (sensi- Intermediate — — Only when vehicle tivity) detected in blind spot : If equipped ■ Toyota parking assist-sensor (P.244) Function Default setting Customized setting Toyota parking assist-sen- — — Level 1 Buzzer volume Level 2 —...
Page 429 8-2. Customization Function Default setting Customized setting Operation after the power — — switch is turned off Operation when the doors — — are unlocked Operation when you approach the vehicle with — — the electronic key on your person Instrument panel ornament light and door trim orna-...
Page 430 When to initialize Reference • After reconnecting or changing the P.118 Power back door 12-volt battery Toyota parking • After reconnecting or changing the P.247 12-volt battery assist-sensor • When the tire inflation pressure is changed such as when changing...
Page 431 Index What to do if... (Troubleshoot- ing) .........430 Alphabetical Index ....433 HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 432 You lose your keys If you think something is  If you lose your mechanical keys, wrong new genuine mechanical keys can be made by your Toyota dealer. (P.394) The hybrid system does not start  If you lose your electronic keys, the risk of vehicle theft increases ...
Page 433 What to do if... (Troubleshooting) If you cannot release the shift lever by (P.169) depressing the brake pedal with the Depending on the situation, other power switch in ON (P.167) types of warning buzzer may also sound. (P.369, 377) The steering wheel cannot be turned after the hybrid An alarm is activated and the system is stopped...
Page 434 What to do if... (Troubleshooting) When a problem has occurred If you have a flat tire  Stop the vehicle in a safe place and replace the flat tire with the spare tire. (P.381) The vehicle becomes stuck  Try the procedure for when the vehicle becomes stuck in mud, dirt, or snow.
Page 435 Alphabetical Index Alphabetical Index Antennas (smart entry & start sys- tem)..........121 A/C ..........272 Anti-lock Brake System (ABS)..258 Air conditioning filter....340 Warning light ......371 Automatic air conditioning system Approach warning ....224, 233 ..........272 Armrest ..........295 Front seat concentrated airflow Assist grips ........295 mode (S-FLOW) ......
Page 436 LTA (Lane Tracing Assist)...206 Cleaning Exterior........302 Multi-information display ..72, 81 Interior........305 RCTA..........251 Radar sensor ......188 Toyota parking assist-sensor..244 Seat belts ........305 Warning message ......377 Wheels and wheel ornaments..302 Distance until next engine oil change Clock.......... 69, 72 ............71 Coat hooks ........
Page 437 Alphabetical Index Door lock Eco drive mode ......256 Back door........113 Eco score........74, 83 Side doors........109 EDR (Event data recorder) ....6 Smart entry & start system..121 E-Four ..........259 Wireless remote control ..... 107 Elapsed time......76, 85 Doors Electric motor (traction motor)..52 Automatic door locking and unlock- Electric Power Steering (EPS) ..259 ing system .......
Page 438 Alphabetical Index Hybrid transmission....413 Engine ACCESSORY mode ....162 Washer ........323 Compartment ......319 Fog lights Engine switch......160 Replacing light bulbs ....349 Hood .......... 317 Switch.........180 How to start the hybrid system... 160 Footwell light.........283 Identification number....410 Front seats If the hybrid system will not start 392 Adjustment .........125 If your vehicle has to be stopped in...
Page 439 Alphabetical Index Power (ignition) switch ....160 Regenerative braking ....53 Starting the hybrid system..160 Head restraints ......133 Headlights Hybrid System Indicator ..70, 94 Automatic High Beam system..178 Hybrid transmission .....166 Light switch ........ 175 S mode........167 Replacing light bulbs....349 Hybrid vehicle driving tips...264 Head-up display......
Page 440 Alphabetical Index Power windows ......141 License plate lights Light switch ........175 Replacing light bulbs ....349 Light bulbs Replacing ........349 Keyless entry Smart entry & start system..121 Lights Wireless remote control ..... 107 Automatic High Beam system ..178 Fog light switch ......180 Keys Battery-saving function ....
Page 441 Panoramic moon roof Jam protection function ....148 Tire pressure ....77, 85, 330 Operation ........147 Vehicle information display ..76, 85 Warning message ..80, 89, 377 Parking assist sensors (Toyota park- ing assist-sensor).......244 Parking brake Operation ........169 HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 442 Alphabetical Index Parking brake engaged warning Radar cruise control (dynamic radar buzzer ........171 cruise control with full-speed Warning light ......374 range) ..........218 Warning message ...... 171 Radiator .........323 Parking lights RCTA Light switch ........ 175 Function ........251 Warning message ......252 Replacing light bulbs....
Page 443 Radar sensor ..... 187, 240 Adjustment .........136 Rain-sensing windshield wipers. 182 Meter control switches ...73, 81 RCTA.......... 252 Stop lights Toyota parking assist-sensor ..244 Emergency brake signal.....259 Replacing light bulbs ....349 Service plug ........55 Shift lever Storage features ......286 Hybrid transmission ....
Page 444 136 Tire inflation pressure display func- Tire pressure warning reset switch tion ...........330 ..........333 Tire pressure warning system ..330 Toyota parking assist-sensor switch Warning light ......372 ..........245 Vehicle-to-vehicle distance switch Tools ..........382 ......... 218, 228 Top tether anchorages ....46 VSC OFF switch ......
Page 445 Emergency towing ..... 363 Towing eyelet ......366 Vanity lights........297 Trailer towing ......159 Vanity mirrors........297 VDIM (Vehicle Dynamics Integrated Toyota parking assist-sensor Function ........244 Management) ......259 Warning message ...... 246 Vehicle data recording .....6 Toyota Safety Sense Vehicle Dynamics Integrated Man- Automatic High Beam ....
Page 446 · Rear view monitor system Slip indicator ......374 · Panoramic view monitor Speed warning light ....375 SRS..........370 Tire pressure ......372 Toyota parking assist-sensor OFF indicator ........373 Warning message..... 80, 89 Warning messages....... 377 Washer Adding........323 Preparing and checking before win- ter ..........
Page 447 Alphabetical Index HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 448 Alphabetical Index HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 449 Alphabetical Index HIGHLANDER HV_GE HIGHLANDER HYBRID_OM_General_OM48K22E...
Page 450 GAS STATION INFORMATION Auxiliary catch lever (P.317) Fuel filler door (P.186) Hood lock release lever (P.317) Fuel filler door opener (P.186) Power back door switch (P.116) Tire inflation pressure (P.415) : If equipped Fuel tank capacity 65 L (17.1 gal., 14.2 lmp. gal.) (Reference) Fuel type Unleaded gasoline only...

Toyota Highlander Hybryd Owner's Manual

For Safety and Security

For Safe Use before Driving

Child Safety

Theft Deterrent System

Vehicle Status Information and Indicators

3 Before Driving

Key Information

Adjusting the Seats

Adjusting the Steering Wheel

4 Driving

Before Driving

Driving Procedures

Refueling

5 Interior Features

Using the Air Conditioning

6 Maintenance and Care

Maintenance and Care Cleaning and Protecting the

Do-It-Yourself Maintenance

7 When Trouble Arises

Quick Links

Summary of Contents for Toyota Highlander Hybryd

Toyota Highlander Hybryd Owner's Manual

For Safety and Security

For Safe Use before Driving

Child Safety

Theft Deterrent System

Vehicle Status Information and Indicators

3 Before Driving

Key Information

Adjusting the Seats

Adjusting the Steering Wheel

4 Driving

Before Driving

Driving Procedures

Refueling

5 Interior Features

Using the Air Conditioning

6 Maintenance and Care

Maintenance and Care Cleaning and Protecting the

Do-It-Yourself Maintenance

7 When Trouble Arises

Quick Links

Related Manuals for Toyota Highlander Hybryd

Summary of Contents for Toyota Highlander Hybryd

Table of Contents