ADEMCO AlarmDecoder AD2 Install Manual

PLEASE READ THIS LICENSE AGREEMENT CAREFULLY
This license governs use of the accompanying firmware. If you use the device, you accept this license. If you do
not accept the license, do not use the device.
The embedded devices firmware ("Software") is licensed, not sold, to you by Nu Tech Software Solutions, Inc. ("Nu
Tech Software Solutions") for use only under the terms of this License, and Nu Tech Software Solutions reserves
any rights not expressly granted to you. You own the device on which the Software is stored, but Nu Tech Software
Solutions, its licensors and sub-licensors retain ownership of the Software itself.
1. Definitions
The terms "reproduce," "reproduction" and "distribution" have the same meaning here as under U.S. copyright law.
"You" means the licensee of the software. "Your company" means the company you worked for when you
downloaded the software. "Reference use" means use of the software by you or within your company as a
reference, for the sole purposes of developing your product, debugging your products, maintaining your products,
or enhancing the interoperability of your products with the software, and specifically excludes the right to
distribute the software outside of your company or to any third party.
2. Grant of Rights
(A) Copyright Grant- Subject to the following terms and conditions, Nu Tech Software Solutions grants to the end
user ("You") a non-exclusive, non-transferable, fully paid and royalty-free license, without the right of sublicense, to
use the Product solely in the form of the binary firmware image provided, only to the extent necessary to use the
AD2USB hardware. Notwithstanding the foregoing, this License does not apply to the source code or object code
of the Product. This license is not a sale. You may not rent, lease, or lend the Product. Nu Tech Software Solutions
may cancel this LICENSE if you do not abide by its terms and conditions. This LICENSE applies to updates or
supplements to the original Product, unless we provide other terms along with the update or supplement.
RESERVATION OF RIGHTS. Nu Tech Software Solutions reserves all rights not expressly granted to you in
this LICENSE. Title and copyrights to the Product remain with Nu Tech Software Solutions.
3. Limitations
(A) No Trademark License- This license does not grant you any rights to use the Licensor's name, logo, or
trademarks.
(B) If you begin patent litigation against the Licensor over patents that you think may apply to the software
(including a cross-claim or counterclaim in a lawsuit), your license to the software ends automatically.
(C) LIMITATION ON REVERSE ENGINEERING, DECOMPILATION, AND DISASSEMBLY. You may not reverse engineer,
decompile, or disassemble the Product. You may not copy the Product or transfer it to other devices without the
express prior written consent of Nu Tech Software. Notwithstanding any prior agreement you may have with Nu
Tech Software.
(D) The software is licensed "as-is." You bear the risk of using it. In no event will Nu Tech Software Solutions, its
parent or subsidiaries or any of the licensors or sub-licensors, directors, officers, employees or affiliates of any of
the foregoing be liable to you for any consequential, incidental, indirect or special damages whatsoever (including,
without limitation, damages for loss of business profits, business interruption, loss of business information and the
like), whether foreseeable or or unforeseeable, arising out of the use of or inability to use the Software or
accompanying written materials, regardless of the basis of the claim and even if Nu Tech Software Solutions or a
Nu Tech Software Solutions representative has been advised of the possibility of such damage. Nu Tech Software
Solutions' liability to you for direct damages for any cause whatsoever, and regardless of the form of the action,
will be limited to replacement of the Software that caused the damages. THE LIMITATION WILL NOT APPLY IN
CASE OF PERSONAL INJURY ONLY WHERE AND TO THE EXTENT THAT APPLICABLE LAW REQUIRES SUCH
LIABILITY. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
4. General
(A) This License will be construed under the laws of the State of Oregon. If any provision of this License shall be
held by a court of competent jurisdiction to be contrary to law, that provision will be enforced to the maximum
extent permissible, and the remaining provisions of this License will remain in full force and effect. If you are a
U.S. Government user, then the Software is provided with " RESTRICTED RIGHTS" as set forth in subparagraphs (c)
(1) and (2) of the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19 or subparagraph (c)(1)
(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.277-7013, as applicable.
Manufacturer: Nu Tech Software Solutions, 11575 SW Pacific HWY, Suite 109, Tigard, Oregon 97223
5. Termination
(A) This License is effective until terminated. This License will terminate immediately without notice from Nu Tech
Software Solutions or judicial resolution if you fail to comply with any provision of this license. Upon such
termination you must destroy the Software, all accompanying written materials and all copies thereof, and
Sections 3, and 4 will survive any termination.
(p4)
AlarmDecoder (AD2) Install Guide v2.5
Ademco Vista and DSC Power Series Alarm to Computer interface adapter
Video Install Tutorials are available on our website at
http://www.alarmdecoder.com
Before you start...
Please take a moment and read this manual before you install the AD2 to
your alarm panel. Rushing into the install of devices like this can
result in damage to the device or accidental activation of your alarm and
alerting of your alarm company.
Please use caution when using this device. You should notify your
monitoring company you are testing your alarm prior to installing this
device or when testing with this device.
Introduction
Thanks for purchasing the AlarmDecoder adapter. The AD2 device was
designed to work with a wide range of Ademco Vista as well as the DSC
Power Series alarm panels.
The device has different connection options including RS232 Serial, USB
serial and 5v or 3.3v uP compatible TTL serial. The AD2USB and AD2Pi
serial settings are 115200,n,8,1 and for AD2Serial the baud is 19200. On
some models it is also possible to adjust the baud rate via a jumper
setting.
Drivers (AD2USB Only)
If you are running windows you can get the Virtual COM port drivers
from FTDI http://www.ftdichip.com/Drivers/VCP.htm. In many cases your
computer may already have this driver if you have ever used an FTDI
based USB2Serial device as many of them are based upon FTDI chips. These
drivers are installed for you with our free software keypad installer
available on our website.
If you are running Linux you can use the ftdi_sio driver. This should
automatically load when you connect the device if you are using a
relatively new distribution of Linux. For OSX and many other operating
systems the drivers can be found at http://www.ftdichip.com/FTDrivers.htm
Connecting to the Alarm Panel
The AD2 device requires all four keypad bus wires from the alarm panel
to be connected to operate correctly but only consumes ~30mA. Connect
all 4 of the keypad bus wires from the panel to your AD2 as shown. We
suggest you perform this connection while the alarm panel is powered
down and the battery is disconnected. When power is connected to the AD2
the LED indicator will flash a pattern indicating its state.
When ground isolation is required the AD2USB version offers 20kv ground
isolation between the host controller and the alarm panel.
(p1)