Genie 40681504070 Instructions

40681504070, 11/2018
UNIVERSAL REMOTE
INSTRUCTIONS
NOT FOR USE WITH ANY GARAGE DOOR OPENER MANUFACTURED PRIOR TO 1993. NON-
CONTACT SAFETY REVERSING SYSTEM (PHOTOCELLS) MUST BE IN PLACE AND OPERATIONAL.
WARNING
!
MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.
• DO NOT install transmitter unless the door operator's safety device works as required by the door
operator's manual.
• Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving
door parts.
• Keep people clear of opening while door is moving.
• DO NOT allow children to play with the transmitter or door operator.
If safety reverse does not work properly:
• Close door then disconnect opener using the manual release handle.
• DO NOT use transmitter or door operator.
• Refer to Door and Door Opener Owner's Manuals before attempting any repairs.
The universal remote can be programmed to operate many brands and types of garage door openers.
Locate the brand and opener specifications by consulting the label on the opener head, the instruction manual, the
current remote controls for the opener, or the original manufacturer of the opener.
Below are the brands and specifications that this remote is compatible with and the methods that can be used to
program them. Use Chart A below to find your opener/specification combination and then proceed to an available
programming method. ALL combinations shown can be programmed using the CLONING METHOD.
Chart A
AVAILABLE PROGRAM METHOD
Brand Name Megahertz (MHz) & Specification Notes
Genie® 315/390 MHz, Intellicode® I, 1995-current
Overhead Door® 315/390 MHz, CodeDodger® I, 1995-current
*Chamberlain® 315 MHz, Purple Learn Button, Security +®, 2006-2014
*Chamberlain® 390 MHz, Orange/Red Learn Button, Security +®, 1996-2005
*Chamberlain® 390 MHz, Yellow Learn Button, Security +2.0®, 2011-current
*Chamberlain® 390 MHz, Green Learn Button, Billion Code®, 1993-1995
Genie® 315/390 MHz, Intellicode® II, 2010-2011
Overhead Door® 315/390 MHz, CodeDodger® II, 2010-2011
Sommer® 310 MHz, Rolling Code
Linear® 318 MHz, Mega Code®
Wayne Dalton® 372.5 MHz, Rolling Code, 1999-current
Ryobi® 372.5 MHz, Rolling Code
Guardian® 303 MHz, Fixed Learn Code
Xtreme® brand 303 MHz, Fixed Learn Code
Marantec® 315 MHz, Fixed Learn Code
*Chamberlain® 390 MHz, Fixed Dip Switch
FAAC® 433.92 MHz, Rolling Code
CLONING METHOD
Genie® 390 MHz, Fixed Dip Switch, 1993-1995
This method will work with ALL brands and speci ations
NICE® 433.92 MHz, Rolling Code
noted here if you have an existing operational remote.
Overhead Door® 390 MHz, Fixed Dip Switch, 1993-1995
Stanley® 310 MHz, Fixed Dip Switch, 1993-current
*Chamberlain = LiftMaster®/Craftsman®
Genie and Intellicode are registered trademarks of The Genie Company. All other listed names
and trademarks are the property of their respective owners.
NOTE: During programming, the garage door opener will operate. Ensure that the
garage door opening is clear of personnel or any obstructions.
STEP 1 - ACTIVATE REMOTE/BUTTON LAYOUT & LED
LED - The LED will light with each button press and
will also light in response to button presses during
different programming modes.
Activation Tab: Pull tab to activate the remote.
NOTE: If you have more than one of the same brand/MHz opener, please note that all 4 buttons can be
programmed individually from each other. You may use any combination of programming methods
available for your opener/specification combination to achieve your desired button setup.
OPTION 1: QUICK START METHOD
You may use 1 of the 4 manufacturer pre-set buttons on the remote as indicated below if you have
any of these brands/specifications.
Button 1: Genie Intellicode 1 or Overhead Door CodeDodger I
Button 2: Chamberlain® with a PURPLE LEARN Button
Button 3: Chamberlain® with a ORANGE/RED LEARN Button
Button 4: Chamberlain® with an YELLOW LEARN Button*
*CHAMBERLAIN® YELLOW LEARN BUTTON? Move directly to instruction on the top right of this sheet
1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.
2. Press and release the pre-set button on the universal remote that corresponds with your opener
slowly and deliberately several times until the garage door opener operates. Programming for this
button is complete.
QUICK START LEARN
OPTION 2: LEARN METHOD
METHOD METHOD
Pre-set Button Number of
PUT THE UNIVERSAL REMOTE INTO LEARN MODE & SELECT A BUTTON
Number on Button Presses
Remote 1. Press and hold down the Genie universal remote button #2.
2. While still holding down button #2, press the universal remote button #4 - four times.
1 1
3. Release both buttons.
1 1
The BLUE LED on the remote will begin flashing. You will have 15 seconds to complete your entry.
2 2
4. Press the button of your choice on the universal remote the required number of times indicated
3 3 in the LEARN METHOD column next to your opener and specification in Chart A.
Wait the remainder of the 15 seconds. The blue LED will give a long blink and then go out.
4 4
5
PROGRAMMING THE UNIVERSAL REMOTE TO THE OPENER
6
CHAMBERLAIN® YELLOW LEARN BUTTON? Move directly to instruction on the top right of this sheet
6
1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.
2. Press and release the button you just programmed slowly and deliberately several times until the
7
garage door opener operates. Programming for this button is complete.
8
9
OPTION 3: CLONING METHOD
10
11
The Genie universal remote can clone an existing operational remote for any of the garage door
opener brands/specification combinations listed in Chart A.
11
PUT THE UNIVERSAL REMOTE INTO CLONING MODE & SELECT A BUTTON
12
1. Place the original remote and the Genie universal remote within 2" - 4" of each other.
2. Press and hold down the Genie universal remote button #1.
3. While still holding down button #1, press the universal remote button #2 - four times.
CLONING METHOD
This method will work with 4. Release both buttons.
ALL brands and specifiations
The WHITE LED on the remote will begin flashing. You will have 20 seconds to complete your entry.
noted here if you have an
5. Hold down the existing operational button on the original remote until the new universal remote
existing operation remote.
blinks change from slow WHITE BLINKS to rapid BLUE blinks.
6. Once the universal remote BLUE LED is blinking rapidly, press the button of choice on the
universal remote slowly and deliberately. The LED will turn solid and then go out.
PROGRAMMING THE UNIVERSAL REMOTE TO THE OPENER
CHAMBERLAIN® YELLOW LEARN BUTTON? Move directly to instruction on the top right of this sheet
1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.
2. Press and release the button you just programmed slowly and deliberately several times until the
garage door opener operates. Programming for this button is complete.
* CHAMBERLAIN® YELLOW LEARN BUTTON INSTRUCTIONS:
1 2
For use with Chamberlain® technology with a YELLOW LEARN button:
1. Press the LEARN button on the garage door opener for 2-3 seconds and then release.
3 4
2. Press and release the pre-set button or the button you just programmed slowly and deliberately
several times until the garage door opener operates. Let it run until it stops.
3. Press the LEARN button again on the garage door opener for 2-3 seconds and then release.
4. Press and release the button you just programmed slowly and deliberately several times until the
garage door opener operates again. Let it run until it stops. Programming is complete.
FACTORY DEFAULT: If at any time the remote needs to be cleared and returned to its factory default
settings, press and hold down button #3 while pressing button #4 - four times. The blue LED will give
a long blink and then go out. For the 'LEARN METHOD' and the 'CLONING METHOD' , this will clear any
existing programming and return the remote to its original factory default settings. For the pre-set
buttons that have been learned to an opener already, you must clear these in the same manner you
would clear original transmitters from the head. Please consult your opener manual for instruction.
You may also (for all methods) simply program over of what has previously been done.
PROGRAMMING ASSISTANCE: If the opener does not activate after the
steps shown, repeat steps or contact Customer Care by website chat (www.
geniecompany.com) or by phone at: 1-800-354-3643 for programming
assistance. You may also scan this QR code for additional information and links.
Changing the Battery:
Remove small phillips head backing screw.
Pry case open with small coin or screwdriver.
Replace battery with CR2032 coin cell.
For
Patent Information: www.geniecompany.com/patent,
©2018 GMI Holdings DBA, The Genie Company
For help or answers please contact Customer Care by website chat
(www.geniecompany.com) or by phone at 1-800-354-3643 for programming
assistance.
FCC Part 15.21 Statement:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC / IC Statement:
This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
PARTS
Visor Clip
Dock
Key Chain