Schlage BE365 Installation Instructions Manual
Keypad deadbolt
Hide thumbs
Also See for BE365:
- User manual ,
- Programming/operating manual (12 pages) ,
- Installation instructions manual (9 pages)
Table of Contents
Advertisement
Quick Links
*23780000*
23780000
Model BE365
Place Label Here
Poner la etiqueta aquí
Placer l'autocollant ici
Tools Needed
• Phillips screwdriver
Optional
• Tape Measure
• Flathead Screwdriver
• Pencil
• Wood Block
• Hammer
Additional Parts
Optional Bolt
Faceplate
Key
Prepare for Installation
IMPORTANT NOTES
•
DO NOT use a power drill for installation!
•
Use a screwdriver to remove product from packaging.
•
Install and test lock with door open to avoid being locked out.
•
Pay special attention to step 1. If lock is installed with
the cam in the wrong position, the lock will not function
properly!
a
Check door dimensions.
See consumer.schlage.com/Service-Support for door preparation
instructions if dimensions are different.
2³⁄₄" (70 mm)
OR
2³⁄₈" (60 mm)
Door Edge
Keypad Deadbolt
Default Codes
Códigos de predeterminado
Codes du défaut
Keypad
2¹⁄₈" (53 mm)
Hole
5¹⁄₂" (140 mm)
Minimum
Baseplate
Baseplate
Screws (2)
Strike
Bolt
Latch/Strike
Screws (4)
b
Adjust bolt length, if necessary.
Measure the dimension shown. If the measurement is 2C\v" (70 mm),
extend the bolt.
2³⁄₈" (60 mm)
No adjustment needed.
Customer Service Atención al cliente Service à la clientèle
Calling From: Si llama desde: Tout appel provenant de:
U.S.A.
Estados Unidos
États-Unis
d'Amérique:
(888) 805-9837
Cover
Screws (2)
Cover
Reinforcement
Screws (2)
Reinforcement
Plate
2³⁄₄" (70 mm)
OR
Rotate faceplate 180° to extend.
Not Extended
Canada
Canadá
Canada:
(800) 997-4734
Installation Instructions
© Allegion 2018
Printed in U.S.A.
23780000 Rev. 06/18-f
Extended
Mexico
México
Mexique:
018005067866
Advertisement
Table of Contents
Related Manuals for Schlage BE365
Summary of Contents for Schlage BE365
- Page 1 Pay special attention to step 1. If lock is installed with the cam in the wrong position, the lock will not function properly! Check door dimensions. See consumer.schlage.com/Service-Support for door preparation instructions if dimensions are different. No adjustment needed. Rotate faceplate 180° to extend.
- Page 2 Change faceplate, if necessary. Install bolt. Choose the drawing that matches your door edge. If the hole has no mortise, change to the circular faceplate. Door Edge No change necessary. Wood Block (Not Included) Door Edge Actual Size CAUTION Bolt must remain retracted throughout installation! Retracted Extended...
- Page 3 Did bolt extend? Install cover. Actual Size No. Lock is not installed Yes. Lock is correctly. Remove lock and installed correctly. reinstall. Pay close attention to cam position in step 1. For troubleshooting information, go to schlage.com/faqs-keypad.
- Page 4 * The first four numbers must be different from all of the User Codes currently in the lock. More Programming, Warranty, and Registration Information For more programming, warranty, and service information, go to Register your product at RegisterMySchlage.com, or use a mobile schlage.com/faqs-keypad, or use a mobile device with the code device with the code below: below:...
- Page 5 Mesurez la dimension illustrée. Si la mesure est de 70 mm ( 2C\v po), Si les dimensions sont différentes, visiter le site consumer.schlage. déployez le pêne. com/Service-Support pour plus d’information à propos des 2³⁄₈" (60 mm) 2³⁄₄"...
- Page 6 Si es necesario, cambie la placa frontal. Instalar el perno. Changez la têtière au besoin. Installer le verrou. Elija el dibujo que coincida con el borde de su puerta. Si el orificio no tiene mortaja, cambie por la placa frontal circular. Sélectionnez le dessin qui correspond à votre bord de porte. Pour un orifice sans mortaise, optez pour une têtière circulaire. Borde de la puerta Bord de la porte No es necesario realizar cambios. Aucun changement Bloque de Bloc en bois requis.
- Page 7 Extienda el perno (cerradura). Pêne déployé (verrouillage). Ubique la batería en el soporte y coloque los cables. 1. Presione 1. Appuyez Placez la pile dans support et insérez les fils. el botón sur le Schlage. bouton Se acepta Tout routage Schlage. cualquier de fil est 2. Gire la perilla 2.
- Page 8 Renseignements additionnels concernant la programmation, la garantie et l’enregistrement Para obtener más información sobre programación, garantía e Registre su producto en RegisterMySchlage.com o use el información sobre el servicio, diríjase a schlage.com/faqs-keypad siguiente código desde un dispositivo móvil: o use el siguiente código desde un dispositivo móvil: Enregistrez votre produit sur RegisterMySchlage.com ou utilisez...