Siemens REV23.03RF Operating Instructions

en
Operating Instructions
REV23.03RF
Commissioning and quick start
1. Receiver (REV-R.03/1)
Switch on power and press "RESET" button for
about 4 seconds: Orange LED_2 flashes briefly.
Then, press "SET" button for about 4 seconds:
Orange LED_2 flashes slowly; learning mode is
active.
Within 25 minutes press "ESC" button on
REV23.03RF for about 4 seconds: Orange LED_2
flashes fast and briefly; LED_1 changes from red to
flashing green.
After commissioning, the unit will operate
automatically.
2. Transmitter (REV23.03RF)
1. 2.
1. Remove controller from its base and open cover
of the battery compartment.
2. Remove the black battery transit tab. The
controller will switch itself on.
3. Close the battery compartment and replace the
controller.
Selecting the operating mode
The operating mode selector enables you
to select 5 different operating modes:
•
Automatic operation with a maximum of 3
heating / cooling periods
•
Continuously comfort mode
•
Continuously economy mode
•
Continuously frost protection mode
•
24-hour mode with 1 comfort period
Changing temporarily the current
setpoint temperature
The change is
maintained until
° C
the next switching
point is reached!
1. When pressing the or
first time, the currently valid setpoint temperature
will be displayed. It can be readjusted in
increments of 0.2 °C (max. +/-4 °C).
2. After a short time, the initial display will
automatically appear again.
Changing temporarily the
temperature setpoint (savings tip)
In operating modes
button can be pressed to make a manual
change from comfort to economy mode,
or vice versa. The change will
automatically be cancelled when
reaching the next switching point or when
selecting another operating mode.
(Press button approximately for
4 seconds to transmit test telegrams.)
Symbole
"Time" menu
"Temperature"
T
menu
"Heating
periods" menu
"Absence"
menu
Battery
change
Absence
Functions of the roller selector
Escape button
Press the Esc button to return to the menu level previously activated or to leave
the menu level in a number of steps until you reach the initial display
(the settings currently displayed will be accepted).
(Press button approximately for 4 seconds to transmit learning telegram.)
Setting the time of day and the weekday
•
Adjustable in operating modes
CLICK
h
If no button is pressed for a short time, the setting
displayed will be accepted and the initial display will
appear again.
Changing temperatures long-term
•
Adjustable in operating modes
CLICK
button for the
° C
and , this
If no button is pressed for a short time, the setting
displayed will be accepted and the initial display will
appear again.
Siemens SBT / HVAC Products
Heating active
Cooling active
Automatic
operation
Continuously
comfort mode
Continuously
economy
mode
Frost
protection
Press:
• You access the menu
level
• You activate the menu
• You save the inputs
• You switch to the next
CLICK
menu item
• You accept the menu
item
, ,
h
, ,
° C
° C
24-hour mode
Comfort
setpoint
Economy
setpoint
Current weekday
Setpoint frost
protection
Weekday group
Absence
setpoint
Weekend group
Not used with
this unit
Entire week
1 heating
period
Time schedule
Roll:
•
You go from one menu to the
next
+
•
You change the setting
variables (temperature in
increments of 0.2 °C, time in
increments of hours and
minutes)
•
You select predefined functions
and
1. Press: You access the menu level;
the clock flashes.
2. Press: You accept the menu;
the hours flash.
3. Roll: Set the current hour.
4. Press: You save the input;
the minutes flash.
5. Roll: Set the current minute.
6. Press: You save the input;
the weekday flashes.
7. Roll: Select the current weekday.
8. Press the Esc button to return to the menu level:
the T menu flashes.
(Change not necessarily required; press
the Esc button again to return to the
initial display.)
and
1. Press: You access the menu level;
the clock flashes.
2. Roll: Toward the display to the T menu.
3. Press: You accept the menu;
symbol flashes.
4. Press: You accept ;
the setpoint flashes.
5. Roll: Set the comfort temperature
6. Press: You save the input;
symbol flashes.
7. Press: You accept ; the setpoint flashes.
8. Roll: Set the economy temperature.
9. Press: You save the input;
symbol flashes.
10. Press: You accept ; the setpoint flashes.
11. Roll: Set the frost protection temperature.
12. Press: You save the input, symbol
flashes.
Adjustment not required; not used
with this unit.
13. Press the Esc button to return to the menu level:
The heating periods
(Change not necessarily required; press
the Esc button again to return to the
initial display.)
CE1B2265en
2 heating
periods
3 heating
periods
menu flashes.
28.10.2005