Rules For Safe Operation; Important Safety Information - Yard Works 60-3856-2 Operator's Manual

The purpose of safety symbols is to attract your
attention to possible dangers. The safety symbols,
and their explanations, deserve your careful attention
and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or
warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates
danger, warning or caution. Attention is
required in order to avoid serious personal
injury. May be used in conjunction with
other symbols or pictographs.
NOTE: Advises you of information or instructions vital
to the operation or maintenance of the
equipment.
READ ALL INSTRUCTIONS
BEFORE OPERATING
WARNING: When using the unit, you must
follow the safety rules. Please read these
instructions before operating the unit in order
to ensure the safety of the operator and any
bystanders. Please keep these instructions for
later use.
• Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
• Do not operate this unit when tired, ill or under the
influence of alcohol, drugs or medication.
• Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
• Before each use, thoroughly inspect your unit for loose
or damaged parts. Do not use until adjustments or
repairs are made.
• All guards and safety attachments must be installed
properly before operating the unit.
• Inspect the area before starting the Blower/ Vacuum.
Remove all debris and hard or sharp objects such as
glass, wire, etc.
• Use the unit only in daylight or good artificial light.
• Keep all bystanders, especially children and pets, at
least 50 feet (15 m) away from the unit while operating.
ELECTRICAL SAFETY WARNINGS
DANGER: When using electric gardening
appliances, basic safety precautions should
always be followed to reduce the risk of fire,
electric shock and personal injury. Carefully
read and understand the entire operator's
manual before using your unit. Pay close
attention to the operating instructions and
safety warnings.

RULES FOR SAFE OPERATION

SYMBOL MEANING
DANGER : Failure to obey a safety warning
will result in serious injury to yourself or to
others. Always follow the safety
precautions to reduce the risk of fire,
electric shock and personal injury.
WAR NI NG : Failure to obey a safety
warning can result in injury to yourself and
others. Always follow the safety
precautions to reduce the risk of fire,
electric shock and personal injury.
CAUTION: Failure to obey a safety warning
may result in property damage or personal
injury to yourself or to others. Always follow
the safety precautions to reduce the risk of
fire, electric shock and personal injury.
• Since the tool is double-insulated, a 2-wire extension
cord (an extension cord without a ground) may be
used. A 3-wire extension cord (an extension cord with
a ground) that uses a NEMA type connector (parallel
blade, U ground) is recommended. Extension cords
are available from your local retailer. Use only round-
jacketed extension cords approved for outdoor use.
• This tool is double-insulated. Repair or replace
damaged cords.
• To reduce the risk of electrical shock, this unit has a
polarized plug (one blade is wider than the other). This
unit will fit with a polarized plug in one way only. If the
plug does not fit fully into the unit, reverse the plug. If
it still does not fit, use a cord with the correct
connection. Do not modify the unit in any way.
WARNING: To reduce the risk of electrical
shock, use only SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-W or
SJTOW-A cord types.
MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR
120 VOLT APPLIANCES USING 0-12 AMPS*
Cord length (ft.) 25
Wire size (AWG)* 16
*The wire size (AWG) for appliances using 12 to 16
amps is 14 AWG for 25 feet, 12 AWG for 50 feet, and
not recommended for 100 or 150 feet.
• CORD SETS: Make sure your cord set is in good
condition, with a cord that is heavy enough to carry
the current that your unit will draw. An undersized cord
set will cause a drop in line voltage resulting in a loss
of power, as well as overheating. The table shown
above illustrates the correct size to use depending on
the cord length and nameplate amperage rating. If in
doubt, use the next heavier size line gauge. The
smaller the gauge number, the heavier the cord. To
prevent the cord from disconnecting from the unit, use
the cord hook shown in the Operating Instructions.
50 100 150
16 16 14
3