EINHELL TE-MS 18/210 Li Original Operating Instructions page 14

blade.
p) Let the blade reach full speed before
contacting the workpiece. This will reduce
the risk of the workpiece being thrown.
q) If the workpiece or blade becomes
jammed, turn the mitre saw off . Wait for
all moving parts to stop and disconnect
the plug from the power source and/
or remove the battery pack. Then work
to free the jammed material. Continued
sawing with a jammed workpiece could cause
loss of control or damage to the .mitre saw.
r) After fi nishing the cut, release the switch,
hold the saw head down and wait for the
blade to stop before removing the cut-
off piece. Reaching with your hand near the
coasting blade is dangerous.
s) Hold the handle fi rmly when making an
incomplete cut or when releasing the
switch before the saw head is completely
in the down position. The braking action
of the saw may cause the saw head to be
suddenly pulled downward, causing a risk of
injury.
Additional safety precautions:
•
Use saw blades which are designed for
the purpose and for the material being
cut.
•
Use only blades which are recommended
by the manufacturer and comply with EN
847-1.
•
Use only blades with diameters, hole
diameters and tooth pitches which
conform with the technical data set out in
the original operating instructions.
•
Use only blades with rotating speeds
shown on the blade which are equal to or
higher than the rotating speed shown on
the power tool.
•
Do not use saw blades that are blunt,
bent or damaged.
•
Check the direction of rotation whenever
you change the saw blade. There are
arrows marked on the machine and saw
blade to show the direction of rotation. They
must match.
•
Wear gloves to avoid getting cut when
you transport and change the saw blades.
Whenever practicable, saw blades must be
carried in a container.
•
Before use, check that the safety guard
for the saw blade is in proper working
order. If it does not close automatically or
is damaged, do not use the equipment any
Anl_TE_MS_18_210_Li_SPK7_USA.indb 14 Anl_TE_MS_18_210_Li_SPK7_USA.indb 14
EN
more. In this case, contact the manufacturer
or an authorized customer service outlet to
get it professionally repaired.
•
If a switch is damaged or defective,
arrange for it to be replaced by the
manufacturer or an authorized customer
service outlet.
•
Replace worn or damaged table inserts
in the saw table with a replacement part,
or arrange for them to be replaced by the
manufacturer or an authorized customer
service outlet.
•
Only allow repairs to the equipment to
be carried out by the manufacturer or an
authorized customer service outlet using
original parts, otherwise the user may
suffer an accident.
•
Connect a dust extractor to the extractor
adapter on the machine.
•
Make sure that there is adequate stability
by always securing the machine to a
workbench or a table. Use the holes in the
machine's base frame to secure the machine.
Bolt the base frame to a workbench or a table.
•
Secure long workpieces against falling
off, e.g. using standard roller stands.
•
The extensions to the workpiece support
must be fastened and used at all times
while work is in progress
•
The machine is designed for cutting wood
and wood-type materials. To prevent the
saw blade overheating, perform cuts quickly
using blades that are properly sharpened.
•
Do not use this saw to cut fire wood.
•
The clamping device for securing the
workpiece must be used at all times. Do
not cut workpieces which are too small to
clamp securely with the clamping device.
•
Transport the machine by the carry
handles and the machine's base frame
only.
•
If the machine is equipped with a laser,
this laser may not be replaced by a
different type of laser. Repairs to the laser
are only allowed to be carried out by the
manufacturer or an authorized customer
service outlet.
•
The saw blade must be stationary
whenever you carry out any tidying up or
cleaning work. Do not remove any cutting
residues or other parts of workpieces from
the cutting zone while the machine is running
and the saw unit is not at rest (at the top).
•
If you need to use an extension cable,
- 14 -
05.08.2019 14:05:51 05.08.2019 14:05:51