SkyLink SW-100 Quick Start Manual

Skylink ® Control Module
1. INTRODUCTION
Control Module Model SW-100 is a wireless transceiver. It can receive
signal from the AAA+ TM control panel, and other transmitters to turn on /
off the plugged in device. Once the plugged in device is activated,
SW-100 will send a confirmation signal back to AAA+
Please follow the instructions below to set up the control module.
2. PROGRAM THE CONTROL MODULE TO THE
TM
AAA+ CONTROL PANEL
Both control panel and control module are transceivers, meaning they can
transmit and receive signals from each other. For home automation, the
user will initiate an action from the control panel, such as sending a signal
to turn on the light, then the control module will receive such signal and
respond. The control module will then send back a confirmation to the
control panel to indicate the light has been turned on.
Therefore, during programming, it is required to program 2 things:
1. Signal from control module to control panel (confirmation signal)
2. Signal from control panel to control module (command signal)
Turn on
(command
signal)
Control
Panel
Confirm on
(confirmation
signal)
Part 1 Learn signal from Control Module to Control Panel
Step Keys Function
[PROG] Enter
1
[MPIN] Programming
mode
[4] Select learn
2
control module
programming
[1] to [5]
Select control
3
module location
(Max. 5 control
modules)
Activate the
Send signal
4
control
from control
module by
module to
pressing its
control panel.
learn button
once quickly.
Model SW-100
TM control panel.
Control
Module
Control
Module
Description Note
Enter master 3 beeps for valid
password to password. 1 long beep for
programming invalid password.
mode
After [4] is entered, some
zone LEDs will flash or stay
off. The zone LEDs
represent whether that zone
is already occupied by
another control module.
**See Table A.
Select the location After you have selected the
[1], [2], [3], [4], or
control module location, that
[5]. zone LED will be on.
You will hear
Once the signal
is transmitted to [Device X Accepted],
where "X" is the control
the Control Panel,
module location.
that signal will be
stored.
2. PROGRAM THE CONTROL MODULE TO THE
TM
AAA+ CONTROL PANEL (CONT)
ZONE LED DESCRIPTION
O f f Zone is not occupied by any control module
Flashes once This zone is occupied by another control module.
Programming another remote to this zone will overwrite
the previous control module.
Flashes twice This zone is occupied by a remote. You can still
program a control module to this zone, and it will not
overwrite the remote you have in this zone.
This zone is occupied by a remote AND a control
Flashes once,
module. If you program another control module to this
then twice
zone, it will overwrite the previous control module, but
not the remote.
** Table A: Zone LED status for learning control module.
Control Module [1] is represented by zone LED 1
®
Part 2 Learn signal from Control Panel to Control Module
Step Keys Function
Press and Enter
1
hold the learn Programming
button on the mode
Control
Module until
its LED starts
to flash.
[6] to [0] Transmit an ON
2
signal for the
selected device
from the Control
Panel to the
Control Module.
CONTROL MODULE TRANSMIT
LOCA TION BUTTON [X]
1
2
3
4
5
This row :
Buttons for
Learning Control Module
Description Note
LED on the Control
Module will flash
indicating it is in
learn mode.
Refer to the chart After [X] is entered, you will
below to determine hear [Device X On]
indicating you have trans-
which button [6] to
[0] to press. mitted an ON signal for
device X, where X is the
You should transmit
the "ON" command Control Module Location.
for the selected The LED on the Control
Module should be off,
device.
indicating it has learned the
signal, you may now release
the learn button and the LED
will stay on again.
6
7
8
9
0