Sears Candy Cane Pathway Sculpture Instruction Sheet

2013 Standard / Sears
Outdoor 3pc Candy Cane Pathway Sculpture Instruction Sheet (English)
Date: 5/31/13
OUTDOOR 3PC CANDY CANE PATHWAY
SCULPTURE
If you should have any problems with this item, or if it does
not light in assembly, DO NOT RETURN IT to the place of
purchase. Please call our toll free number 1-888-831-6656,
and a trained representative will assist you. Our Customer
Service Center is open throughout the year:
Monday-Friday: 8:00am-4:30pm CST
Holiday weekends:
Last weekend of November: 8:00am-4:30pm CST
First weekend of December: 8:00am-4:30pm CST
ASSEMBLY INSTRUCTIONS:
NOTE: No tools required (Hammer optional).
NOTE: Retain carton for storage.
1. Carefully remove all parts from the carton. Your 3pc Candy
Cane Pathway should include the following (Fig 1):
3 Candy cane top sections
3 Candy cane bottom sections (one with plug attached)
3 Candy cane bases
6 Lawn stakes (2 Lawn stakes for each completed candy cane)
Replacement LED bulbs & covers
Top sections
Fig 1
Bottom sections
Lawn Bases
Replacement LED
stakes
bulbs and covers
2. Place a base on level ground (with eyelets on top) (Fig 2).
Fig 2
3. Connecting a bottom section to a base: Place the flat bottom of
a bottom section atop of the rectangular base.
Note: Be sure that the light string cord is not between bottom
section and the base.
4. Using the angled pegs from the base as a guide; slide the
bottom section on to the base until the two angled pegs of
bottom section insert into the two eyelets from the base (Fig 3).
11.5"
5. Connecting the top section to
LED13
the bottom section: Begin by
positioning the top section
above the bottom section.
Aligning the angles correctly;
lower the top section onto the
bottom section while inserting
the two wire posts from the
top section into the two
corresponding sleeves from
the bottom section (Fig 4).
6. Secure the top section onto
the bottom section by
inserting the side-arm hooks
from the top section into the
eyelets on the bottom section
(Fig 5).
7. Connect the light string of the
top section to the light string
of the bottom section by
aligning the flat ends of both
connectors as shown and
connect them together. Slide
the screw cover from the
"male" connector over the
"female" connector and
tighten (Fig 6).
Fig 6
8. Repeat Steps 2 to 7 to complete the assembly of the other 2
candy canes.
9. Once all 3 candy canes are assembled; they will now need to be
electrically connected.
Begin by extending and untangling the light string wiring,
which also contains the plug, and is already connected to 1 of
the 3 candy canes.
As shown in Fig 6; connect the "female" connectors from the
light string wiring to the "male" connectors, which are located
at the base of each candy cane (Fig 7).
Fig 7
NOTE: BE SURE THAT THE WIRING IS NOT TANGLED; AND THAT
ALL 3 CANDY CANES CAN BE EXTENDED TO THEIR FULL
POTENTIAL.
10. Push or gently hammer lawn stakes into the ground, securing
each candy cane's base. Angle each stake 45 degrees toward
Fig 3
the center (Fig 8).
Fig 4
11. Check the item for any loose, unlit or damaged bulbs. Although
it will still operate, the bulbs must be replaced promptly to
ensure the performance and life expectancy of the item.
LED replacement:
Before changing LEDs, make sure set is unplugged.
Step 1: Grasp plug and remove from the
receptacle or other outlet device.
Do not unplug by pulling cord.
Fig 5
Step 2: Unscrew plastic cover from LED socket.
Step 3: Hold LED lamp by the plastic base and
pull LED/base straight out of the socket.
Step 4: Replace LED with only 3 volt, 20 mA
LED type lamp (provided with product).
Step 5: Place the plastic cover over the LED
lamp and screw it back onto the socket.
Actual LED cover may vary depending on product purchased.
12. To illuminate, fully insert the plug into a working GFCI outlet or
an outdoor rated extension cord.
MAINTENANCE
This outdoor sculpture includes replacement bulbs and caps
for any replacements that you need to perform on your
sculpture. If extra parts are needed, contact the Customer
Service Team at 1-888-831-6656.
STORAGE INSTRUCTIONS
1. Leave assembled if storage room permits or disassemble,
placing all components in the original carton.
2. Store in cool, dry location away from sunlight.
TROUBLESHOOTING
1. Unplug the product and check to see that the GFCI outlet is
functioning.
2. Unplug the product and check all light string connections. This
product uses low voltage coaxial connections. To connect the
light strings, align the flat ends of both connectors as shown and
connect them together. Slide the screw cover from the "male"
connector over the "female" connector and tighten (Fig 6).
NOTE: DO NOT USE A DIMMER SWITCH OR INSTALL ANY
ADDITIONAL CHRISTMAS LIGHTING OR ORNAMENTATION
THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS MAY
RESULT IN DAMAGE TO THIS PRODUCT OR CAUSE PERSONAL
INJURY. THIS ACTION WILL RESULT IN A VOID OF THE LIMITED
WARRANTY OF THIS PRODUCT.
2 YEAR LIMITED WARRANTY
This product was pre-tested before shipment and date coded.
In keeping with the National Electric Code, this product is
intended for seasonal (90 days max.) installation and use. The 2
year limited warranty covers repair or replacement of this
product if it fails to light. This product is covered under
warranty only if it is used as intended for 2 holiday seasons (90
days max. per season). If product fails to light, please contact
our Customer Service Center toll free number 1-888-831-6656
for instructions on obtaining repair or replacement. Allow four
(4) to six (6) weeks for repair or replacement. This warranty is
void if the product is misused or damaged in any way.
Questions, call customer service toll free at 1-888-831-6656 or
visit us on the web at www.santasbest.com.
Made in China
Printed in China
This is not a toy, for decorative use only.
Distributed by Santa's Best®
Riverwoods, IL 60015 USA
www.santasbest.com
Fig 8
COVER COVER
COVER
COVER
BASE
BASE
SOCKET
LED
SOCKET
11.5"