Table of Contents
Advertisement
IV. OPERATION
IV. a - TOP DOOR LATCH
To adjust the latch on the top door turn the safety screw
on each side clockwise to tighten and counter-clockwise
to loosen.
000-60330-00
Turn Safety Screws
Clockwise To Tighten
TURN THE SAFETY SCREWS
CLOCKWISE TO TIGHTEN
THE LATCH
The Latch
DETAIL B
SCALE 2 : 1.5
Fig. 2
PROPRIETARY AND CONFIDENTIAL
THIS DOCUMENT CONTAINS PROPRIETARY AND CONFIDENTIAL DATA OF TRAULSEN & CO. INC.
NO DISCLOSURE, REPRODUCTION OR USE OF ANY PART THEREOF MAY BE MADE WITHOUT
WRITTEN PERMISSION OF TRAULSEN & CO. INC.
ANY VENDOR SUPPLYING PARTS UNDER THIS DRAWING AGREES NOT TO REVISE ANY PHYSICAL,
DIMENSIONAL, MATERIAL OR PERFORMANCE CHARACTERISTICS OF SUCH PARTS AFTER
APPROVAL BY TRAULSEN & CO. INC. GROUP OF VENDOR SAMPLES UNLESS AUTHORIZED IN
IV. b - OPERATION DISPLAY INDICATORS
WRITING BY TRAULSEN & CO. INC.
Milk Coolers do not require manual defrosting. However,
manual defrost option is available on the control, if required.
During normal operation, the display shows either the
temperature measured or one of the following indications:
IV. c - MILK COOLER OPERATION
During normal operation, a milk cooler continuously circulates
above-freezing cabinet air through the evaporator coil. An
Off-Cycle defrost occurs every 8 hours for a maximum length
of 50 minutes to melt any frost which may accumulate on
the coil during the compressor "ON" cycle. With standard
holding milk coolers, high relative humidity is also maintained
to prevent dehydration of stored product.
IV. d - REFRIGERATING PRODUCT
Milk Cooler models will satisfactorily refrigerate an assorted
load of food items. Allow space between articles to permit
free air circulation. Do not overload at any one time with
warm food products and expect immediate results. A certain
amount of time is required to remove heat from items before
operating temperatures can be attained. The system is
designed for storage of refrigerated product.
Opening the door will increase the temperature in the cabinet
and will require a certain amount of time to recover. Also,
after peak service periods or after warm product is loaded,
the milk cooler will require a certain amount of time for the
temperature to return to the normal operating range.
SCALE 1 : 2
NAME
DATE
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN
S.KUKOLJ 5/16/14
.XX
.03
FRACTIONS
1/32
CHECKED
.XXX
.015
ANGLES
1/2
ENG APPR.
HOLES
.005
MFG APPR.
PARTS ARE TO FREE OF BURRS AND SHARP EDGES
MATERIAL
Q.A.
INSTRUCTION DR. LATCH ADJUSTMENT
-
COMMENTS:
FINISH
--
SIZE
DWG. NO.
A
000-60330-00
DO NOT SCALE DRAWING
NO SCALE
WEIGHT: 0
SHEET 1 OF 1
V. CARE AND MAINTENANCE
V. a - CLEANING THE CONDENSER/FILTER
The most important thing you can do to insure a long,
reliable service life for your Traulsen is to regularly clean
the condenser coil and or filter.
WARNING: DISCONNECT ELECTRICAL POWER
SUPPLY BEFORE CLEANING ANY PARTS OF THE UNIT.
To clean the condenser/filter, first disconnect electrical power
to the cabinet and remove the system side cover.
Proceed to vacuum or brush any dirt, lint or dust from the
finned condenser coil/filter, the compressor and other cooling
system parts. If significant dirt is clogging the condenser fins
or filter, use compressed air to blow this clear. To replace
the system side cover reverse the process.
V. b - REPLACING THE DOOR GASKETS
To remove the gasket to be replaced, grasp it firmly by one
corner and pull it out. Before attempting to install a new
gasket, both the unit and the gasket itself must be at room
REV.
B
temperature. Insert the four corners first by using a rubber
mallet (or hammer with a block of wood).
After the corners are properly inserted, work your way
towards the center from both ends by gently hitting with a
mallet until the gasket is completely seated in place (see
figure below for proper gasket placement).
NOTE: The gasket may appear too large, but if it is installed
as indicated above it will slip into place.
NOTE: System gasket attached with screw.
-3-
Top Door
Gasket
Front Door
Gasket
Fig. 3
Advertisement
Table of Contents
