Download Print this page
Central Machinery 67536 Owner's Manual & Safety Instructions

Central Machinery 67536 Owner's Manual & Safety Instructions

3-1/2 cubic ft. cement mixer

Advertisement

Quick Links

Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2013 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
NOTICE
FOR CEMENT AND
MORTAR ONLY.
Do not use with Epoxy
2-part resin mix.
20i

Advertisement

loading

Summary of Contents for Central Machinery 67536

  • Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
  • Page 2 Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. Page 2 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 3 These carry important safety information. heavy enough to carry the current your product If unreadable or missing, contact will draw. An undersized cord will cause a drop Harbor Freight Tools for a replacement. Item 67536 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4 4. When using more than one extension cord excessive heat, and damp or wet areas. to make up the total length, make sure each cord contains at least the minimum wire size required. (See table a.) Page 4 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 5 2. Do not smoke during use. Nicotine reduces ups to ensure medical problems are not being the blood supply to the hands and fingers, caused or worsened from use. Pregnant women increasing the risk of vibration-related injury. Item 67536 For technical questions, please call 1-888-866-5797. Page 5...
  • Page 6 Specifications Electrical Input 120 VAC / 60 Hz / 3.5 A Motor No Load Speed 1820 RPM Drum Speed 36 RPM Drum Capacity 3-1/2 Cubic Feet Drum Opening 15" Page 6 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 7 3. Insert Leg (79) into Stand so that bolt holes line up. 4. Fasten together using Hex Bolts (69, 70), Flat Washers (55) and Hex Flange Nuts (5). Tighten with a wrench until secure. Figure c 5. Place Stand upright. Item 67536 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8 (72) Motor cover (9) Motor cover (9) 13. Attach Control Handle to Arm shaft with a Hex Bolt (42), two Flat Washers (45), and a nut (44). Figure F Page 8 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 9 Screw on the side of the Pulley’s hub. in contact with any moving parts. 30. Check all connections to verify that all screws, nuts, and bolts are securely tightened. Item 67536 For technical questions, please call 1-888-866-5797. Page 9...
  • Page 10 Functions Motor assembly control upper Drum Handle Mixer Blade Handle control Stand plate Wheel Bracket Lower Drum Wheel Page 10 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 11 Handle. First, disengage the locking pins by pulling the Control Handle away from the drum and then pushing on the Handle until the desired angle is reached. Re-engage the locking pins. Item 67536 For technical questions, please call 1-888-866-5797. Page 11...
  • Page 12 Motor Bracket bolts and lift Bracket upward. Tighten Motor Bracket bolts and retest tension. 5. Replace Motor Cover. Page 12 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 13 See Extension Cords in GROUNDING section. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 67536 For technical questions, please call 1-888-866-5797. Page 13...
  • Page 14 Bearing 6002ZZ Hex Bolt M8×70 Ring Shield Ø38 Hex Bolt M14×30 Support Bracket Seat Spring Washer 14 Pinion Shaft Flat Washer Gear Flat Key 5×12 Stand Gear Cover Cross-Head Screw M4×30 Page 14 For technical questions, please call 1-888-866-5797. Item 67536...
  • Page 15 Some parts are listed and shown month and year of purchase instead. for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175329752 when ordering parts. Item 67536 For technical questions, please call 1-888-866-5797. Page 15...
  • Page 16 pLEaSE rEaD tHE FOLLOWinG carEFuLLy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.