Yamaha CBX-K1XG Mode D'emploi page 48

1.4.17 Effect1 Depth (Reverb Send Level)
Messages which adjust the send level for the Reverb effect.
CNTRL# PARAMETER
91 Effect1 Depth
1.4.18 Effect3 Depth (Chorus Send Level)
Messages which adjust the send level for the Chorus effect.
CNTRL# PARAMETER
93 Effect3 Depth
1.4.19 Effect4 Depth (Variation Effect Send Level)
Messages which adjust the send level for the Variation effect.
CNTRL# PARAMETER
94 Effect4 Depth
If Variation Connection (page App-13) = 1 (System), this message
sets the send level for the Variation effect.
If Variation Connection = 0 (Insertion), this has no effect.
1.4.20 Data Increment / Decrement (for RPN)
Messages which increase or decrease the MSB value of Pitch Bend
Sensitivity, Fine Tune, or Coarse Tune in steps of 1.
CNTRL# PARAMETER
96 RPN Increment
97 RPN Decrement
The data byte is ignored.
When the maximum value or minimum value is reached, the value
will not be incremented or decremented further.
(Incrementing the Fine Tune will not cause the Coarse Tune to be
incremented.)
1.4.21 NRPN (Non-Registered Parameter Number)
Messages which adjust a Voice's vibrato, filter, EG, drum setup or
other parameter settings.
CNTRL# PARAMETER
98 NRPN LSB
99 NRPN MSB
First send the NRPN MSB and NRPN LSB to specify the param-
eter which is to be controlled. Then use Data Entry to set the value
of the specified parameter.
* Note that once the NRPN has been set for a channel, subse-
quent data entry will be recognized as the same NRPN's value
change. Therefore, after you use the NRPN, you should set a
Null (7FH, 7FH) value to avoid an unexpected result.
The following NRPN numbers can be received.
NRPN DATA ENTRY
MSB LSB MSB PARAMETER NAME and VALUE RANGE
01H 08H mmH Vibrato Rate
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 09H mmH Vibrato Depth
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 0AH mmH Vibrato Delay
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 20H mmH Filter Cutoff Frequency
mm : 00H - 40H - 7FH (-64 - 0 - +63)
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
DATA RANGE
0...127
0...127
DATA RANGE
0...127
0...127
01H 21H mmH Filter Resonance
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 63H mmH EG Attack Time
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 64H mmH EG Decay Time
mm : 00H - 40H - 7FH (-64 - 0 - +63)
01H 66H mmH EG Release Time
mm : 00H - 40H - 7FH (-64 - 0 - +63)
14H rrH mmH Drum Filter Cutoff Frequency
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
15H rrH mmH Drum Filter Resonance
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
16H rrH mmH Drum EG Attack Rate
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
17H rrH mmH Drum EG Decay Rate
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
Applies to both Decay1 and 2.
18H rrH mmH Drum Instrument Pitch Coarse
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
19H rrH mmH Drum Instrument Pitch Fine
mm : 00H - 40H - 7FH (-64 - 0 - +63)
rr : drum instrument note number
1AH rrH mmH Drum Instrument Level
mm : 00 - 7F (0 - max)
rr : drum instrument note number
1CH rrH mmH Drum Instrument Pan
mm : 00H - 40H - 7FH
(random, left - center - right)
rr : drum instrument note number
1DH rrH mmH Drum Instrument Reverb Send Level
mm : 00H - 7FH (0 - max)
rr : drum instrument note number
1EH rrH mmH Drum Instrument Chorus Send Level
mm : 00H - 7FH (0 - max)
rr : drum instrument note number
1FH rrH mmH Drum Instrument Variation Send Level
mm : 00H - 7FH (0 - max)
rr : drum instrument note number
MSB 14H–1FH (for Drum) is valid only if the Multi Part param-
eter (page App-13) PART MODE = DRUMS 1 or DRUMS2 for
that channel. (If PART MODE = DRUM, no values will be changed.)
1.4.22 RPN (Registered Parameter Number)
Messages which offset, or add or subtract values from a Part's pitch
bend sensitivity, tuning, or other parameter settings.
CNTRL# PARAMETER
100 RPN LSB
101 RPN MSB
* Note that once the RPN has been set for a channel, subsequent
data entry will be recognized as the same RPN's value change.
Therefore after you use the RPN, you should set a Null (7FH,
7FH) value to avoid an unexpected result.
MIDI Data Format
DATA RANGE
0...127 (Default:7FH)
0...127 (Default:7FH)
App-7