SECTION 1 PRECAUTIONS SAFETY PRECAUTIONS Prior to shipment from the factory, JVC products are strictly can increase the high voltage value and cause X-ray emis- inspected to conform with the recognized product safety and sion from the cathode ray tube.
Page 3
1.1.2 Safety Check after Servicing Examine the area surrounding the repaired location for damage (4) Leakage current test or deterioration. Observe that screws, parts and wires have been Confirm specified or lower leakage current between earth returned to original positions, Afterwards, perform the following ground/power cord plug prongs and externally exposed tests and confirm the specified values in order to verify accessible parts (RF terminals, antenna terminals, video...
Page 17
Quality point When you assemble the unit, please check the following points for keeping the quality. Bottom As CIS (optical image stabilizer) makes heavy use of magnets, ensure that chips of steel metal, etc. are not attached. Do not touch the movable parts at the top and bottom of the CIS. (Place in bag until it is to attached.
Page 18
Make sure that the CMOS FPC is not caught between the boards. Pay attention to use the correct fastening screw for the junction board. (The shortest screw. Using a wrong screw will damage the OP.) As the tabs are located more inwards than past models, remove the Make sure that the FFC between TRIG PWB and MAIN PWB is on top of the TRIG PWB connector.
SECTION 4 ADJUSTMENT PREPARATION • 4.1.1 Precaution Torque Driver Be sure to use to fastening the mechanism and exterior parts This model is specially adjusted by using PC. However, if parts such as the following are replaced, an because those parts must strictly be controlled for tightening adjustment is required.
Page 20
JIG CONNECTOR CABLE CONNECTION Connection procedure Remove the COVER JIG. CN9019 EXTENSION CONNECTOR JIG CONNECTOR CABLE COVER JIG SERVICE SUPPORT SYSTEM (Software) MENU CABLE PERSONAL COMPUTER 1-20 (No.YF414<Rev.002>)
SECTION 5 TROUBLESHOOTING This service manual does not describe TROUBLESHOOTING. (No.YF414<Rev.002>)1-21...
Page 22
<BOARD INTERCONNECTIONS> O P E R A T I O N CMOS 053 PWB CMOS PWB B TU TERMINAL I N T M I C For IMX053 SNAPSHOT C I S O P B L O C K ( J 1 X ) CN401 QGF0321F1-33X To CONNECTOR...
Page 23
<MAIN(MAIN IF) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. M A I N P W B TELE,WIDE,PHOTO-KEY,TRIGGER,GND to OPERATION UNIT C N 9 0 1 4 QGF0534F5-06X EMZ6.8N-X D9021...
Page 24
<MAIN(SUB CPU) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. R1014 LIT_3.0V LIT_3.0V AL_2.8V R1063 AL_2.8V REG_2.8V_R1064 REG_2.8V R1064 REG_2.8V C1001 C1002 C1003 C1004 OPEN OPEN OPEN...
Page 25
<MAIN(FELIX) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. TL3039 TL3038 R3012 OPEN VDDE_2.8V R3015 OPEN CIS_GAIN_Y CIS_GAIN_Y OPEN C3079 CIS_GAIN_P CIS_GAIN_P R3018 CIS_OFFSET_Y OPEN CIS_OFFSET_Y SCL/TORCH...
Page 26
<MAIN(REG) SCHEMATIC DIAGRAM> MODEL MODEL Note : The parts numbers in the schematic diagram are for references only. WIFI NO-WIFI WIFI NO-WIFI SYMBOL NO. SYMBOL NO. R6505 NRSA6AD-224W NRSA6AD-364W C6301 NCJ20JM-226X-A OPEN C6303 OPEN When replacing the parts, refer to the PARTS LIST. R6506 NRSA6AD-562W NRSA6AD-153W...
Page 27
<MAIN(AUDIO) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. From REG Q2462 2SC5383/F/-X REG_5.0V REG_2.8V REG_1.8V L2461 R2462 4.7k To IF2 AU_SIG/R R2463 C2463 C2462 AU_SIG/L From Subcpu...
Page 28
<MAIN(eMMC) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. # C8011 OPEN # C8008 # C8003 # C8007 OPEN OPEN OPEN # C8009 OPEN Remember to OPEN back during ES1 AH11 MODEL...
Page 29
<MAIN(CIS HALL AMP) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. K7001 NQR0129-002X OPEN IC7004 XC6220B271MG-X VOUT REG_2.8V C7025 OPEN L7001 NQL382M-100X REG_5.0V C7009 C7006 R7026 R7030...
Page 30
<MAIN(CIS DRIVE) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. L7052 F7051 NQL382M-100X NMFZ007-R50X-K REG_5.0V_F7051 REG_5.0V_L7052 REG_5.0V C7059 L7051 NQL382M-100X REG_5.0V REG_5.0V_L7051 REG_5.0V R7064 R7059 R7053 R7061...
Page 31
<MAIN(WI FI BLOCK) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. ( F o r W I F I M o d e l o n l y ) WIFI_RST WIFI_RST MOD_3.3V_CTRL...
Page 32
<MAIN(SD IF) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. from/to JUNCTION to Trigger + GYRO QGF0543F3-30X CN9515 C N 9 5 2 1 QGF0543F3-20X C9506 C9507...
Page 33
<MAIN(ASST LED) SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. # IC5001 AAT1272IWO-X # L5001 NQLK25N-2R2X RSET # C5003 2.2u 0.082 FLOUTA FLEN FLGND AGND FLOUTB UNREG...
Page 34
<CMOS SCHEMATIC DIAGRAM> Notes : 1. The parts number in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. 2. The schematic diagram is only for reference. Avoid replacing individual parts. Replace the entire unit only. When CMOS BOARD ASSEMBLY needs replacement, replace the CMOS FRAME ASSEMBLY in whole because it cannot be replaced alone C M O S C M O S S E N S O R I M X 0 5 3...
Page 35
<JUNCITON SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. TO MIC CN203 QGF0543F3-08X J U N C T I O N To OP(J1X) CN201 from/to MAIN PWB QGF0321F1-25X CN205...
Page 36
<MONITOR SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. QGF0319F1-35X CN301 M O N I T O R From Main PWB REG_2.8V REG_LED D303 D304 OPEN REG_LED...
Page 37
<TRIGGER SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. 0 5 T R I G G E R TO SPEAKER C N 9 5 1 6 QGA1001F1-02X SPK+ SPK-...
Page 38
<FRONT SCHEMATIC DIAGRAM> Note : The parts numbers in the schematic diagram are for references only. When replacing the parts, refer to the PARTS LIST. 0 6 F R O N T MODEL FLASH TORCH SYMBOL NO CL690S2BWO1SD-X CL-690S-2WQSD-X D601 OPEN CN602 QGA1001F1-02X...
Page 39
<MAIN CIRCUIT BOARD> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) <01>MAIN CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH SAME TYPE AND RATED FUSE(S). LYB10327-001D ATTENTION : POUR UNE PROTECTION PERMANENTE CONTRE LES RISQUE D'INCENDE, REMPLACER LES FUSIBLES PAR UNAAUTRE DE MEME TYPE ET DE MEME TENSION.
Page 41
<CMOS CIRCUIT BOARD> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) <02>CMOS The Circuit board is only for reference. Avoid replacing individual parts. LYB30021-001A Replace the entire unit only. When CMOS BOARD ASSEMBLY needs replacement, replace the CMOS FRAME ASSEMBLY in whole because it cannot be replaced alone.
Page 42
<MONITOR CIRCUIT BOARD> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) <04>MONITOR LYB30016-001A FOIL SIDE(B) UL MARK COMPONENT SIDE(A) TP302 C345 D324 R350 R348 L323 R304 L301 C323 R303 C354 C355 C312 K301 K302 K303 K304...
Page 43
<FRONT CIRCUIT BOARD> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) <06>FRONT LYB30017-001A COMPONENT SIDE(A) FOIL SIDE(B) FRONT R607 R606...
Page 44
JVC KENWOOD Corporation Home & Mobile Electronics Business Group, Imaging Products Business Division 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-0022, Japan (No.YF414<Rev.002>) Printed in Japan...
Page 46
Title Line No.YF414<Rev.001> No.YF414<Rev.002> Description AC ADAPTER AC-V10M AC-V11U AC CORD YES(IRAM) PARTS LIST MODEL No. LIST Model No. No.YF414<Rev.002> GZ-V500BUA GZ-V505BTW FINAL ASSEMBLY [M1MM] Part No. Symbol Part Name Description Models <Rev.001> <Rev.002> M1MM 109 ------------ LY38050-002D FRONT UNIT (Addition) 1 01 M1MM 112...
Page 47
Part No. Symbol Part Name Description Models <Rev.001> <Rev.002> 04 C301 ------------ NCJA0JK-105W-A C CAPACITOR (Addition) 1 01 TRIGGER BOARD ASSEMBLY [05] Part No. Symbol Part Name Description Models <Rev.001> <Rev.002> 05 PW501 ------------ LYA30017-01A2 TRIGGER BOARD ASSY (Addition) 1 01 FRONT BOARD ASSEMBLY [06] Part No.
Page 48
JVC KENWOOD Corporation Home & Mobile Electronics Business Group, Imaging Products Business Division 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-0022, Japan (YF414-R002) Printed in Japan No.YF414<Rev.001>...
Page 49
PARTS LIST CAMCORDER GZ-V505BTW (No.YF414<Rev.001>)1/15...
Page 50
■ PRECAUTIONS ON SCHEMATIC DIAGRAMS Due to the improvement in performance, some part numbers shown in the circuit diagrams may not agree with those indicated in the Parts List. The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for reference only.
Page 51
FINAL ASSEMBLY<M1> The instruction manual to be provided with this product will differ according to the destination. No.YF414 created date:2012-03-16 (No.YF414<Rev.001>)3/15...
Page 52
FINAL ASSEMBLY<M1> The instruction manual to be provided with this product will differ according to the destination. FRONT ASSEMBLY FRONT BOARD ASSEMBLY <06> TRIGGER BOARD ASSEMBLY <05> No.YF414 created date:2012-03-16 (No.YF414<Rev.001>)4/15...
Page 53
FINAL ASSEMBLY<M1> The instruction manual to be provided with this product will differ according to the destination. MAIN BOARD ASSEMBLY <01> JUNCTION BOARD ASSEMBLY <03> No.YF414 created date:2012-03-16 (No.YF414<Rev.001>)5/15...
Page 54
FINAL ASSEMBLY<M1> The instruction manual to be provided with this product will differ according to the destination. UPPER ASSEMBLY MONITOR BOARD ASSEMBLY <04> No.YF414 created date:2012-03-16 (No.YF414<Rev.001>)6/15...
Page 55
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local FINAL ASSEMBLY <M1MM> QAL1374-001 JUNC FPC WJT0281-001A-E E-CARD WIRE TRIG FFC LY38106-001B HLDR(FLEX PWB) ------------ BKT JACK LY38173-001A L.FRAME ASSY WJA0049-001A-E E-S ID WIRE FLASH LED WIRE QAN0120-001 MICROPHONE UNIT LY38050-002C FRONT UNIT...
Page 56
PACKING AND ACCESSORY ASSEMBLY <M5> FINAL ASSEMBLY <M1> No.YF414 created date:2012-03-16 (No.YF414<Rev.001>)8/15...
Page 57
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local PACKING AND ACCESSORY ASSEMBLY <M5MM> QAM1308-001 A/V CABLE QAM1369-001 USB CABLE (TYPE A-MINI TYPE B) QAL1323-002 AC P ADAPTOR AC-V11U LY38215-001A BATTERY PACK BN-VG212U LY38306-001A STYLUS PEN QQR0491-002 FERRITE CORE AC P ADAPTER QAM1447-001...
Page 58
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local C3001 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C3002 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C3003 NCBA1CK-104W C CAPACITOR 0.1uF 16V K C3007 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C3008 NCBA1AK-104W C CAPACITOR...
Page 59
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local C7014 NCBA1CK-103W C CAPACITOR 0.01uF 16V K C7015 NCBA1CK-103W C CAPACITOR 0.01uF 16V K C7016 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C7017 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C7018 NCBA1AK-104W C CAPACITOR...
Page 60
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local R3043 NRSA6AJ-474W MG RESISTOR 470kΩ 1/16W J R3044 NRSA6AJ-474W MG RESISTOR 470kΩ 1/16W J R3045 NRSA6AJ-101W MG RESISTOR 100Ω 1/16W J R3046 NRSA6AJ-101W MG RESISTOR 100Ω 1/16W J R3047 NRSA6AJ-101W MG RESISTOR...
Page 61
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local R7022 NRSA6AJ-821W MG RESISTOR 820Ω 1/16W J R7023 NRSA6AJ-821W MG RESISTOR 820Ω 1/16W J R7024 NRSA6AJ-392W MG RESISTOR 3.9kΩ 1/16W J R7025 NRSA6AJ-392W MG RESISTOR 3.9kΩ 1/16W J R7026 NRSA6AJ-392W MG RESISTOR...
Page 62
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local CN9521 QGF0543F3-20X CONNECTOR FFC/FPC (1-20) CN9522 NNZ0239-001X SD CARD CONNE F6003 NMFZ007-R50X-K FUSE 0.5A 50V F7051 NMFZ007-R50X-K FUSE 0.5A 50V F9001 NMFZ028-2R5X-J1 FUSE 2.5A F9028 NMFZ028-2R5X-J1 FUSE 2.5A F9029 NMFZ028-2R5X-J1 FUSE...
Page 63
MODEL MARK GZ-V505BTW Safe Symbol No. Parts No. Parts Name Description Local K272 NQR0573-005X FERRITE BEADS K273 NQR0573-005X FERRITE BEADS MONITOR BOARD ASSEMBLY <04> PW301 LYA30016-01A MONITOR BOARD ASSY IC322 HGDESM031A-X Q341 DRA9143X-X DIGI TRANSISTOR Q341 LTA043EEB-X DIGI TRANSISTOR Q342 DRA9143X-X DIGI TRANSISTOR Q342...