Trane GXAA Installation, Operation And Maintenance Manual page 8

G G e e n n e e r r a a l l S S a a f f e e t t y y R R e e q q u u i i r r e e m m e e n n t t s s
5. Follow installation instructions CAREFULLY to avoid creating unsafe conditions. All wiring
6. Use only the fuel for which the heater is designed (see nameplate). Using LP gas in a heater
7. Make certain that power source conforms to electrical requirements of heater. Disconnect
8. Special attention must be given to any grounding information pertaining to this heater. To
9. Do not insert fingers or foreign objects into the heater or its air moving device. Do not block
10. This heater is intended for general heating applications ONLY. It must NOT be used in
In cases in which property damage may result from malfunction of the heater, a backup system
or a temperature sensitive alarm should be used.
F F i i r r e e H H a a z z a a r r d d a a n n d d T T o o x x i i c c F F u u m m e e s s ! !
F F a a i i l l u u r r e e t t o o f f o o l l l l o o w w i i n n s s t t r r u u c c t t i i o o n n s s b b e e l l o o w w c c o o u u l l d d r r e e s s u u l l t t i i n n d d e e a a t t h h o o r r s s e e r r i i o o u u s s i i n n j j u u r r y y . .
T T h h e e o o p p e e n n e e n n d d o o f f p p i i p p i i n n g g s s y y s s t t e e m m s s b b e e i i n n g g p p u u r r g g e e d d m m u u s s t t N N O O T T d d i i s s c c h h a a r r g g e e i i n n t t o o a a r r e e a a s s w w h h e e r r e e
t t h h e e r r e e a a r r e e s s o o u u r r c c e e s s o o f f i i g g n n i i t t i i o o n n o o r r i i n n t t o o c c o o n n f f i i n n e e d d s s p p a a c c e e s s U U N N L L E E S S S S p p r r e e c c a a u u t t i i o o n n s s a a r r e e t t a a k k e e n n a a s s
f f o o l l l l o o w w s s : :
• •
• •
• •
Unless otherwise specified, the following conversions may be used for calculating SI unit
measurements:
•
•
•
•
•
•
•
•
•
•
•
8
should be done and checked by a qualified electrician, using copper wire only. All gas
connections should be made and leak-tested by a suitably qualified individual, per
instructions in this manual.
that requires natural gas, or vice versa, will create the risk of gas leaks, carbon monoxide
poisoning and explosion.
power before installing or servicing heater. If power disconnect is out of sight, lock it in open
position and tag it to prevent unexpected application of power. Failure to do so could result in
fatal electric shock.
prevent the risk of electrocution, the heater must be securely and adequately grounded. This
should be accomplished by connecting a grounded conductor from the service panel to the
conduit box of the heater. To ensure proper ground, the grounding means must be tested by
qualified field electrician.
or tamper with the heater in any manner while in operation or just after it has been turned off,
as some parts may be hot enough to cause injury.
potentially dangerous locations such as flammable explosive, chemical-laden or wet
atmospheres.
B B y y v v e e n n t t i i l l a a t t i i o o n n o o f f t t h h e e s s p p a a c c e e . .
B B y y c c o o n n t t r r o o l l l l i i n n g g t t h h e e p p u u r r g g i i n n g g r r a a t t e e . .
B B y y e e l l i i m m i i n n a a t t i i n n g g a a l l l l h h a a z z a a r r d d o o u u s s c c o o n n d d i i t t i i o o n n s s
1 inch = 25.4 mm
1 foot = 0.305 m
1 gallon = 3.785 L
1 pound = 0.454 kg
1 psig = 6.894 kPa
1 cubic foot = 0.028 m 3
1000 Btu/Cu. Ft. = 37.5 MJ/m
1000 Btu per hour = 0.293 kW
1 inch water column = 0.249 kPa
liter/second = CFM x 0.472
meter/second = FPM ÷ 196.8
W W A A R R N N I I N N G G
3
MUA-SVX006B-EN