Page 1
A L L H I M N E Y E N T I L A T I O N O O D S NSTALLATION NSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS...
Page 2
® WOLF is a registered trademark of Wolf Appliance, Inc. WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite.
Use & Care Information prior to use. Any questions or problems about the installa- tion should be directed to your Wolf dealer or Wolf Appliance, Inc. at 800-332-9513. You can also visit our website at wolfappliance.com.
Page 4
Wolf internal, in-line and remote blower assemblies are available, refer to page 17. Use only a Wolf blower with the Pro wall chimney hood. IMPORTANT NOTE: Wolf recommends that the Pro wall chimney hood be installed 30"...
Page 5
WIDTH OF HOOD 30" 36" (762–914) TO COUNTERTOP NOTE: Pro wall chimney hoods have a vertical discharge. Dimensions in parentheses are in millimeters unless otherwise specified. OV E R A L L D I M E N S I O N S...
Page 6
P R O WA L L C H I M N E Y I N S TA L L AT I O N The illustration and chart below provides dimensions specific to each Pro wall chimney hood model. These dimensions are critical for proper installation.
Page 7
Wolf recommends the maximum linear duct run be no greater than 50' (15 m). Pro wall chimney hoods have a vertical discharge. IMPORTANT NOTE: There is a possibility of noise issues, if there is a short duct run coupled with a remote blower.
Page 8
W O L F P R O WA L L C H I M N E Y WA L L F R A M I N G IMPORTANT NOTE: There must be a minimum 10" (254) opening in the ceiling to accommodate the ductwork necessary for proper ventilation.
Page 9
I N S TA L L AT I O N I N S T R U C T I O N S H O O D P R E PA R AT I O N Follow these steps to prepare the wall chimney hood for installation: Remove the filters by pressing up at the angle the filters are placed in, then rotate...
Page 10
IMPORTANT NOTE: If an optional duct cover is to be used with the Pro wall chimney hood, follow these instructions before installing the hood: Attach the duct cover from the inside of the hood through the filter opening using the screws provided with the duct cover.
Page 11
I N S T A L L A T I O N IMPORTANT NOTE: If an optional duct cover is to be used with the Pro wall chimney hood, it must be installed before installing the hood— except for the 36" (914) and 42" (1067) wide hoods with an internal blower.
Page 12
W O L F P R O WA L L C H I M N E Y I N S T A L L W I R I N G Risk of electrical shock. This ventilation hood must be properly grounded. This unit should be installed by a qualified electrician in accordance with all applica- I M P O R TA N T...
Page 13
I N S TA L L AT I O N I N S T R U C T I O N S I N S T A L L W I R I N G I N - L I N E O R R E M O T E B L O W E R W I R I N G Remove the hood electrical box cover.
Page 14
F I LT E R I N S T A L L A T I O N Follow these instructions to install filters and grease cups for Wolf Pro wall chimney hoods: Reinstall the internal frame. Refer to Hood Preparation on page 9.
Page 15
Power Cords CTBLOWER-90INT A C C E S S O R I E S Optional acces- sories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance.com. Top of Hood Threaded...
Page 16
Locate the blower so that the length of the duct run and number of elbows and transitions are kept to a minimum. Wolf recommends the maximum linear duct run be no greater than 50' (15 m).
Page 17
I N S T R U C T I O N S B L OW E R A S S E M B L I E S Wolf Pro wall chimney ventilation hoods are shipped without the blower assembly. Wolf internal, in-line and remote blower assemblies are available as sales accessories through your Wolf dealer.
Page 18
P R O WA L L C H I M N E Y T R O U B L E S H O O T I N G IMPORTANT NOTE: If the Pro wall chimney ventilation hood does not operate properly, follow these troubleshooting steps: Verify that power is being supplied to the ventilation hood.